1. Product Overview
This complete set of HTBCCHB front and rear vented brake discs delivers reliable stopping power and efficient heat dissipation for small-displacement off-road vehicles. Designed for durability and performance, these brake discs are a direct replacement for your existing components.
Compatibility: Ideal for 47cc/49cc pocket bikes, 50cc-125cc ATVs, go-karts, and mini off-road vehicles with matching brake system dimensions.

Figure 1: Front and Rear Brake Discs
2. Safety & Warnings
Read all safety information before installation and use. Failure to follow these instructions may result in serious injury or property damage.
- Professional Installation Requirements: This product is a core safety component of the braking system and must only be installed by professional technicians qualified in motorcycle maintenance. Operation by untrained personnel poses fatal safety risks.
- Installation Inspection: Before installation, ensure the brake disc is free from deformation, cracks, and blowholes. After installation, verify that the brake disc is coaxial with the caliper, with no uneven wear or runout; failure to do so may result in brake judder or failure.
- Compatibility Requirements: Only suitable for hydraulic calipers and braking systems of corresponding specifications. Prohibited for use on incompatible vehicle models or modified overloaded applications to prevent brake failure.
- Children Warning: Keep this product out of reach of children to avoid pinching injuries and accidental operation risks.
- Load Limit: Do not use under overloaded conditions or perform prolonged braking on high-speed downhill sections, to prevent overheating and deformation of the brake disc and subsequent brake failure.
3. Setup & Installation
Proper installation is crucial for safe and effective braking. If you are unsure about any step, consult a professional mechanic.
3.1. Installation Preparation
- Completely disassemble the original front and rear brake discs.
- Clean the wheel hub mounting surfaces thoroughly, removing residual oil, impurities, and old gaskets.
- Inspect the wheel hubs for deformation and wear, ensuring the mounting holes are intact and meet installation requirements.
- Inspect the new brake discs for deformation and cracks, ensuring the mounting holes are intact and meet installation requirements.
3.2. Installation Steps
- Align the front and rear brake discs with their corresponding wheel hub mounting positions respectively.
- Tighten the fixing bolts evenly in a diagonal sequence to ensure no runout or deflection of the brake discs.
- Install the corresponding calipers and adjust the clearance between the calipers and the brake discs to ensure no uneven wear, no jamming, and smooth braking.
- Conduct a braking test to confirm sensitive front and rear braking, no shaking, and no abnormal noise, completing the installation.
4. Operating Instructions
Once installed, brake discs require minimal specific operating instructions beyond standard safe riding practices. Always ensure your braking system is in good working order before each ride.
- Apply brakes smoothly and progressively. Avoid sudden, harsh braking unless in an emergency.
- Be aware of brake fade during prolonged or heavy braking, especially on downhill sections. If you notice reduced braking performance, allow the brakes to cool.
- Always use both front and rear brakes appropriately for balanced stopping power.
5. Maintenance & Care
Regular maintenance ensures optimal performance and longevity of your brake discs.
5.1. Storage
- Uninstalled brake discs shall be stored in a dry and ventilated environment to prevent rust and deformation.
5.2. Regular Cleaning
- Regularly clean oil and sediment from the surface of the brake discs to maintain good braking performance and prevent overheating.
- Clean oil, grease, and sediment from the brake disc surface after each ride to prevent uneven caliper wear and brake judder.
5.3. Inspection and Replacement
- Regular Inspection: Inspect the brake disc for wear and deformation every 500 kilometers. Replace it immediately if excessive wear, deformation, or cracks are detected.
- Replacement Interval: Under normal use and maintenance, the service life of this brake disc is approximately 10,000 to 20,000 kilometers. Replace it promptly in case of severe wear or deformation.
5.4. Prohibited Operations
- Do not strike the brake disc with hard objects to avoid deformation.
- Do not drive with partial braking for a long time to prevent overheating and deformation of the brake disc.
6. Troubleshooting
If you experience issues with your brake discs, consider the following common problems and solutions:
- Brake Judder or Vibration:
- Cause: Uneven wear, disc runout, improper installation, or warped disc.
- Solution: Inspect discs for warpage or uneven wear. Re-check installation for proper alignment and bolt torque. Replace if warped or excessively worn.
- Reduced Braking Performance:
- Cause: Oil, grease, or sediment on disc surface; overheating (brake fade); worn brake pads or discs.
- Solution: Clean discs thoroughly with brake cleaner. Allow brakes to cool if overheated. Inspect and replace worn brake pads or discs.
- Brake Noise (Squealing/Grinding):
- Cause: Contamination on disc surface, worn brake pads, improper caliper alignment, or worn discs.
- Solution: Clean discs and pads. Inspect pads for wear and replace if necessary. Check caliper alignment. Replace discs if deeply scored or worn beyond limits.
7. Specifications
Detailed specifications for the HTBCCHB Front and Rear Brake Discs:
| Feature | Front Disc | Rear Disc |
|---|---|---|
| Outer Diameter | 110mm | 158mm |
| Inner Diameter | 40mm | 48mm |
| Mounting Hole Circle | 50mm | 68mm |
| Mounting Hole Diameter | Φ7mm | M8 |
| Weight (Approx.) | 0.22kg | 0.48kg |
| Material | Metal | |
| Item Type | Brake Disks | |
| External Testing Certification | ISO9001 | |

Figure 2: Front Brake Disc Dimensions

Figure 3: Rear Brake Disc Dimensions
8. User Tips
No specific user tips were available from customer reviews or Q&A for this product. Always ensure professional installation and follow all safety and maintenance guidelines for optimal performance and safety.
9. Warranty & Support
For warranty information, technical support, or any product-related inquiries, please contact your original seller or the manufacturer directly. Please have your purchase details ready when contacting support.
A detailed user manual in PDF format may also be available for download from the seller's product page: View PDF Manual