Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your iManAuto AHD720P Car Rear View Camera. This camera is designed to be compatible with BMW's original car screen upgrade CarPlay module and other systems that require a camera installation.
Compatibility: Please verify your vehicle's OEM trunk handle dimensions to ensure compatibility. This camera is suitable for various BMW models, including:
- BMW 3 Series: F30 (2012-2015), F34, F35, F80 (2012-2017)
- BMW 5 Series: F10, F11 (2010-2015), F18 (2012-2017)
- BMW X Series: X3 F25 (2011-2017), X4 F26 (2013-2017), X5 F15 (2013-2017)
- Specific models: 318i, 320i, 530i, 330i, 328i, 535i, 520i, 525i, 320Li, 535Li (various years within the ranges above)
Package Contents
Please ensure all items are present in the package before proceeding with installation:
- Rear Camera x1
- Package Box x1
- 6M RCA Video Cable x1
- 1.4M Power Cable x1
Setup and Installation
Careful installation is crucial for optimal performance. It is recommended to have this installed by a professional if you are not familiar with car electronics.
1. Physical Installation
The camera is designed to replace your car's original trunk handle. Ensure the dimensions match your vehicle's existing handle before installation.
2. Wiring Diagram (General)
Follow the general wiring diagram for connecting the camera to your monitor and power source:
- A: Monitor (Not Included) - This refers to your car's display unit or an aftermarket monitor.
- B: Camera Power Source - The camera requires a 12V DC power supply.
- C: Rear View Camera - The camera unit itself.
Tip: If connecting to an Android DVD head unit, you will need to connect the 6-meter RCA cable's red trigger wire (labeled "A" in the diagram) to the reverse lights power (DC 12-24V+). The other end of this trigger wire (labeled "B") connects to the DVD's reverse trigger wire input.
3. Wiring for Automatic Transmission Cars
For automatic transmission vehicles, refer to the specific wiring instructions below:
- The brown line does not require a connection.
- Connect the REAR CAM signal wire to the CAM 12V input on your display unit.
- Ensure the red cable from the camera power harness is connected to a corresponding red power cable from your vehicle's reverse light circuit.
- The red and black wire pair (likely for ground and an alternative power source) does not require a connection in this setup.
Operating Instructions
Once installed, the camera will automatically activate when the vehicle is shifted into reverse gear, displaying the rear view on your connected screen.
Dynamic Trajectory
The camera features dynamic trajectory lines that adjust with your steering wheel, providing intuitive guidance for parking and maneuvering.
Night Vision
Equipped with top starlight night vision technology, the camera provides a clear view even in low-light conditions, allowing you to park with confidence day or night.
Maintenance
The iManAuto AHD720P camera is designed for durability and minimal maintenance.
- Cleaning: Periodically clean the camera lens with a soft, damp cloth to ensure a clear view. Avoid abrasive cleaners.
- Waterproofing: The camera boasts an IP68 waterproof rating, meaning it is sealed tightly and designed to work reliably in all weather conditions, including rain and car washes.
Integrated Step-down Module
The camera features an integrated step-down module that supports DC 12-24V input. This module ensures low power consumption and prevents overheating, reducing the risk of fire.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No image/signal on screen | Loose cable connections, incorrect wiring, faulty power supply, incompatible display unit. | Check all video and power cable connections. Ensure the camera is receiving 12V DC power. Verify your display unit supports the camera's signal type (AHD720P). |
| Distorted or flickering image | Poor cable connection, electrical interference, damaged cable. | Secure all connections. Ensure video cables are not routed near high-voltage wires. Inspect cables for damage. |
| Night vision not working effectively | Dirty lens, insufficient ambient light for starlight sensor. | Clean the camera lens. While starlight night vision is excellent, extreme darkness may still limit visibility. |
| Dynamic trajectory lines not appearing or incorrect | Feature not supported by the display unit, incorrect settings in the display unit. | Ensure your CarPlay module or display unit supports dynamic trajectory lines. Check the settings of your display unit for camera guidelines options. |
Specifications
| Feature | Detail |
|---|---|
| Brand Name | iManAuto |
| Model | AHD720P Car Rear View Camera (Variant: BMW 8006) |
| Voltage | 12 V (Supports DC 12-24V via integrated module) |
| Item Weight | 0.3 kg |
| Origin | Mainland China |
| Certification | CE |
| Wide Angle | 170° (Golden Fisheye lens) |
| Night Vision | Top Starlight Night Vision (10m visible distance at night) |
| Waterproof Rating | IP68 |
| Dimensions (Approx.) | Length: 164mm, Height: 48mm, Mounting Width: 100mm |
User Tips
- Always double-check the dimensions of your car's original trunk handle against the camera's dimensions before purchasing and installing to ensure a perfect fit.
- For the best image quality, keep the camera lens clean from dirt, dust, and water spots.
- If you experience any issues, first verify all cable connections are secure and correctly wired according to the diagrams.
Warranty and Support
For further details and comprehensive instructions, you may refer to the official user manual PDF:
If you encounter any issues not covered in this manual or require technical assistance, please contact the seller or manufacturer's support channel for expert help.