1. Introduction
The MYOSLIM CO2 Fractional Laser System is a cutting-edge skincare tool designed to rejuvenate and improve skin with advanced laser technology. It utilizes a unique dot matrix system to stimulate collagen production for smoother, firmer skin and treats a variety of skin concerns. This device is suitable for both professional and at-home use, offering a non-surgical solution to enhance skin quality.
It is ideal for addressing fine lines, wrinkles, pigmentation, acne scars, enlarged pores, stretch marks, and for skin resurfacing, scar revision, syringomas, and blepharoplasty. The system features an imported laser arm with three working modes: Fractional, Normal, and Vaginal, ensuring a 360° treatment with the highest energy output and minimal energy loss.
2. Safety Information
WARNING: This device is not intended for medical supervision. Always consult with a qualified professional before use, especially for sensitive areas or pre-existing skin conditions.
- Ensure the device is properly grounded before use.
- Do not operate the device if any part is damaged or malfunctioning.
- Keep the device away from water and other liquids.
- Wear appropriate protective eyewear during operation to prevent eye injury from laser exposure.
- Keep out of reach of children.
- Do not use on irritated, broken, or infected skin.
- Avoid direct eye contact with the laser beam.
- Ensure adequate ventilation during operation.
3. Package Contents
Please check the package carefully to ensure all items are present and undamaged.
CO2 Main Unit: The primary control and power unit of the laser system.
Guide Light Arm: Articulated arm for precise laser delivery.
Fractional Laser Head: For skin resurfacing and scar treatment.
Vaginal Tightening Head: Specialized head for vaginal rejuvenation treatments.
Pulse Head: For specific pulse mode treatments.- Key: For turning the device on/off and security.
- Foot Switch: For hands-free operation during treatment.
- Power Cord: To connect the device to a power source.
4. Specifications
| Feature | Specification |
|---|---|
| Wavelength | 10600nm |
| Laser Apparatus | Sealed off laser device simulated by direct current |
| Optical Beam Quality | TEMOO |
| Output Power | 40W |
| Spot Size | 0.02~0.05mm² |
| Aiming Beam | Red semiconductor laser (635nm, less than 5mw) |
| Beam Transport Device | Articulated arm with 7-joint and balance weight |
| Working Mode | Continuous operation |
| Output Mode | Continuous, single pulse, interval pulse and super pulse |
| Scan Scope | Max 20mmx20mm |
| Scan Graphics | Circle, triangle, square, rectangle, hexagon, ellipse, line |
| Scanning Mode | Random, Normal and Midsplit scan |
| Scanning Speed | More than 10m/s |
| Energy | 1-40W |
| Distance | 0.1-2.6mm |
| Cooling System | Air circulation |
| Power Input | 220V/110V |
| Maximum Power Consumption | 2.3kVA |
| Output Power | 6500W |
| Material | Metal |
| Certification | CE, ROHS |
| Treatment Area | Buttocks, thighs, hips, arms, ABS (and face, vaginal, vulva) |
| Effect | Reduced fat by 21%, Increased muscle mass by 16% (Note: These effects are typically associated with body contouring, not CO2 laser. Please verify with manufacturer.) |
| Contraction (30 min) | More than 20000 times |
| Application | For Commercial |
5. Setup Instructions
5.1 Initial Assembly
- Install the Arm: Carefully install the guide light arm into the base unit.
- Connect Scan Head: Connect the desired scan head (e.g., fractional laser head) to the guide light arm.
- Connect Power & Foot Switch: Connect the power cord to the main unit and a suitable power outlet. Connect the foot switch to its designated port on the main unit.
5.2 Water Filling
Before first use, or if the water level is low, add distilled water to the cooling system.
- Locate the water inlet port on the back of the main unit.
- Using a funnel, slowly add approximately 5 liters of distilled water into the system until the water level indicator shows full.
- Ensure no water spills onto the device.
6. Operating Instructions
6.1 Power On and Main Screen
- Turn On: Insert the key into the key switch and turn it to the ON position.
- Main Screen: The main screen will appear on the display. From here, you can select the desired treatment mode.
6.2 Face Treatment (Lattice Mode)
This mode is used for general facial skin concerns like fine lines, wrinkles, and acne scars.
- From the main screen, select the