APC PW-65A001 / PW-0008 / LM E243073 / ACE-855A

Contents

User Manual

Replacement Power Board for APC AP5717

1. General Description

This document provides instructions for the 65W open-frame switching power board, compatible with models PW-65A001, PW-0008, E243073, and ACE-855A. It is primarily designed for APC AP5717 and similar industrial/equipment applications. The board delivers stable, regulated DC output from a universal AC input.

Overall view of the power board with various components and connectors.
Figure 1: Overall view of the power board.
Close-up of the power board showing the model number SCP050A-201F REV:01 and date 2016.10.15.
Figure 2: Close-up view of the power board's model identification.

2. Safety Precautions

  • Always disconnect AC power before installation, removal, or servicing the board.
  • Do not expose the board to water, moisture, or corrosive gases.
  • Operate within an ambient temperature range of 0°C to +40°C (non-condensing).
  • Ensure adequate ventilation. Do not block heat sinks or airflow around the board.
  • Avoid overloading output circuits.
  • Be aware of the risk of electric shock: internal high voltages can be present even when the unit is unplugged due to capacitor discharge.
  • Use only with properly grounded AC supplies.

3. Electrical Specifications

Power Board Specifications
Category Specification
Input Voltage 90-264 VAC (universal)
Input Frequency 47-63 Hz
Inrush Current < 80 A peak (cold start @ 230 VAC)
Max Input Current 2.0 A @ 115 VAC; 1.0 A @ 230 VAC
Power Rating 65 W max
Short-circuit Protection Auto-recovery
Overload Protection 110-160% rated, auto-recovery
Over-voltage Protection Yes
Over-temperature Protection Yes

4. Installation & Connection

Mounting

  • Secure the board using the designated mounting holes. Use appropriate screws and avoid over-tightening.
  • Maintain adequate clearance around the board for proper airflow and component access.

AC Input (Mains)

Connect to the AC input terminals, typically labeled L (Live), N (Neutral), and GND (Protective Earth):

  • L: Live (AC Line)
  • N: Neutral
  • GND: Protective Earth (ground)

DC Output

  • Connect loads to the DC output connector/pins. Verify the correct voltage rails for your specific model, which are typically +12V, +5V, +3.3V, and GND.
  • GND: Common ground.
  • Ensure correct polarity during connection to prevent damage to the board or connected devices.

5. Operation

  1. Double-check all wiring to ensure correct voltage, polarity, and tightness of connections.
  2. Apply AC power to the board.
  3. The power LED (if present on your model) will illuminate when the output is active.
  4. The board should operate silently under normal low-temperature conditions.
  5. If the board shuts down, follow these steps:
    • Remove AC power.
    • Check for any short circuits or overloads on the output.
    • Wait 1-2 minutes for the board to reset.
    • Reapply power.

6. Troubleshooting

No Output:

  • Verify the AC input voltage and connections are correct.
  • Check the input fuse (if replaceable) for continuity.
  • Inspect the DC output for any short circuits.

Output Drops / Cycles:

  • Check for an overload or short circuit on the output.
  • Ensure sufficient cooling and that the board is not experiencing over-temperature conditions.

Unstable Voltage:

  • Check for loose connections.
  • Inspect for a faulty load or external component connected to the board.

7. Maintenance

  • This power board contains no user-serviceable parts. Do not attempt to open or repair it yourself.
  • Keep the board clean and free of dust to ensure optimal performance and longevity.

8. Warranty & Support

This product comes with a 90-day warranty against manufacturing defects. For repair or replacement services, please contact your supplier directly.

For additional detailed instructions and diagrams, you may refer to the official user manual available in PDF format: View User Manual (PDF).

9. User Tips

This product is intended for professional maintenance personnel. Before purchasing or installing, carefully review the product's pictures, model numbers, board numbers, interface types, and voltage requirements to ensure compatibility with your equipment. Incorrect installation or misjudgment of machine problems can lead to unnecessary losses.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.