ANYFAR NBT (ID4) Retrofit Decoder Box

Contents

ANYFAR Wireless CarPlay & Android Auto Retrofit Decoder Box

User Manual for BMW NBT (ID4) Systems

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your ANYFAR Wireless CarPlay & Android Auto Retrofit Decoder Box. This device integrates wireless smartphone connectivity into your BMW's existing NBT (ID4) infotainment system, utilizing the original screen and iDrive controls.

Safety Information

  • Ensure the vehicle's ignition is off and the battery is disconnected before beginning installation to prevent electrical damage or injury.
  • Do not attempt to operate the device or adjust settings while driving. Always ensure full attention to the road.
  • If you are unsure about any installation steps, seek professional assistance.

Setup

Package Contents

Verify that all items are present in your package:

  • 1 x NBT System Decoder Box
  • 1 x Power Cable Harness
  • 1 x LVDS Cable
  • 1 x RCA/USB Cable
  • 1 x External Microphone (MIC Cable)
  • 1 x WiFi Antenna
NBT System Accessories

Figure 1: NBT System Accessories Included

Compatibility Check

This retrofit kit is exclusively designed for BMW vehicles equipped with the NBT (ID4) head unit. It is not compatible with CIC or EVO ID5/ID6 systems.

Step 1: Verify your original car radio homescreen menu picture.

BMW NBT System Verification

Figure 2: Confirm NBT System (Green Check) vs. Incompatible Systems (Red X)

Step 2: Check the LVDS port on the back of the OEM car screen.

  • The system requires a 6 PIN LVDS port. A 4 PIN port is not compatible.

Suitable Models and Years:

Suitable BMW Models

Figure 3: Compatible BMW Models and Years

SeriesChassisYears
1 SeriesF20/F212013-2015
2 SeriesF222013-2015
3 SeriesF30/F31/F34/F802012-2015
4 SeriesF32/F33/F362013-2015
5 SeriesF07/F10/F11/F182012-2015
6 SeriesF06/F12/F132013-2016
7 SeriesF01/F02/F032012-2014
X3F252013-2016
X4F262014-2016
X5F15/F852014-2016
X6F16/F862014-2016
MINIF562014-2016

Toggle Switch (DIP) Setup

The decoder box features toggle (DIP) switches to configure settings based on your car's screen size. The switches are located on the side of the decoder box, near the LVDS port.

DIP Switch Location

Figure 4: Location of Toggle (DIP) Switches

Set the toggle switch settings according to your car's screen size. For an 8.4 inch screen (640x480), use the following configuration:

DIP Switch Settings for 8.4 inch screen

Figure 5: DIP Switch Settings for 8.4 inch Screen (640x480)

Switch12345678
Setting (On/Off)OffOffOffOffOffOffOffOn

Wiring Diagram

Follow this diagram carefully for all connections. Ensure all cables are securely connected to their respective ports.

Cable Connection Chart

Figure 6: Detailed Cable Connection Chart

Key Connections:

  • MIC IN: Connect the external microphone.
  • GND: Ground connection.
  • 12V Reverse Camera out: Power supply for reverse camera.
  • 12V ACC out: Accessory power output.
  • Back/Reverse Detect: Reverse signal input.
  • 12V input reverse Detect: Input for reverse signal.
  • Front camera video input: RCA input for front camera.
  • Reverse camera video input: RCA input for reverse camera.
  • USB Port: Connect USB flash drives or mobile phones.
  • WiFi antenna: Connect the WiFi antenna (keep away from metal).
  • New power cable: Connect to the original power cable.
  • AUX: Connect to the vehicle's AUX input.
  • New LVDS cable: Connect between the decoder box and the OEM CD host/screen.
WiFi Antenna and USB-AV Cable Connection

Figure 7: WiFi Antenna and USB-AV Cable Connection to Decoder Box

Physical Installation

The CarPlay interface decoder box should be installed in an appropriate space near or on the OEM head unit. Ensure it is secured and does not interfere with other vehicle components.

Installation on OEM head unit

Figure 8: Installation on the OEM Head Unit

Installation beside OEM head unit

Figure 9: Installation Beside the OEM Head Unit

AUX Audio Connection

To enable audio output from the decoder box through your car's speakers, you must connect the AUX cable to your OEM AUX input and switch your car's audio source to AUX.

Car Audio Source Selection

Figure 10: Select AUX as Audio Source

AUX Input Location

Figure 11: Connect to OEM AUX Input

Operating Instructions

Switching Between Systems

After all cables are connected, you can switch between the original BMW system and the CarPlay/Android Auto interface by:

  • Long pressing the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.