WINLINTE 1J0927807D

Contents

WINLINTE ABS Wheel Speed Sensor User Manual

Model: 1J0927807D

Brand: WINLINTE

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your WINLINTE ABS Wheel Speed Sensor. Please read these instructions carefully before proceeding with installation or use. Proper installation is crucial for the correct functioning of your vehicle's Anti-lock Braking System (ABS).

2. Safety Instructions

WARNING: Improper installation may cause traffic accidents, vehicle damage, or personal injury. Professional installation is highly recommended.

  1. Vehicle Preparation: Park the vehicle on a flat, stable ground, apply the parking brake, and turn off the engine completely. For all electrical parts, disconnect the vehicle battery negative terminal first to avoid short circuit or electric shock.
  2. Part Removal: Remove the original old or damaged part in reverse order of factory installation, using proper matching tools. Do not force dismantle to avoid damaging surrounding parts.
  3. Area Cleaning: Clean the installation area thoroughly, check for wear, rust or damage of mounting brackets and related parts, and ensure the mounting surface is flat and clean.
  4. Part Alignment: Align the new auto part with the original mounting position, fix it firmly with standard fasteners (screws, bolts, clips), and ensure no looseness or deviation.
  5. Electrical Connections: Reconnect all wiring harnesses, hoses or connectors correctly. For electrical parts, reconnect the battery after confirming all connections are correct.
  6. Function Test: Start the vehicle, test the function of the new part, check for abnormal noise, leakage or malfunction, and confirm normal operation before use.
  7. Required Tools: Standard wrench set, screwdriver, jack, safety gloves, voltage tester (for electrical parts).
  8. Modifications: Do not modify, disassemble or reprocess this product without authorization, which may lead to fire, electric shock or part failure.
  9. Flammable Materials: Do not install the product on flammable surfaces, or cover it with heat insulation, flammable materials.
  10. Compatibility: Confirm the product is fully compatible with your vehicle model before installation. Incorrect fitment is not covered by warranty.
  11. Personal Protection: Wear personal protective equipment during installation to prevent physical injury.

3. Product Overview

The WINLINTE ABS Wheel Speed Sensor is a critical component for your vehicle's Anti-lock Braking System, designed to accurately measure wheel rotation speed and transmit this data to the ABS control unit. This ensures optimal braking performance and vehicle stability.

WINLINTE ABS Wheel Speed Sensor
Figure 3.1: WINLINTE ABS Wheel Speed Sensor
Close-up of sensor connector pins
Figure 3.2: Close-up view of the sensor's electrical connector pins.
Video 3.1: Product demonstration of the ABS Wheel Speed Sensor.

4. Specifications

FeatureDetail
Product NameABS Wheel Speed Sensor
Part Numbers (OEM NO.)1J0927807D, ALS418, 5S10501
Product ColorBlack
MaterialHigh-Grade Metal & Plastic Composite
CertificationCE, E-Mark, RoHS Compliant
OriginMainland China
High-concerned chemicalNone
Warranty1 year

Compatible Vehicle Information:

  • AUDI: TT (Years: 2001-2006)
  • SEAT: LEON (Years: 2004-2006)
  • VOLKSWAGEN: JETTA (Year: 1998)

Note: Vehicle compatibility is for reference only. Always verify the OE part number on your existing sensor and compare with product images before purchase. The same vehicle model may use different parts depending on region, year, or specific configuration.

5. Installation Instructions

Follow these steps carefully for proper installation of the ABS Wheel Speed Sensor. Refer to the Safety Instructions section before beginning.

  1. Prepare Vehicle: Raise the vehicle safely using a jack and remove the corresponding wheel where the sensor is to be installed.
  2. Locate and Disconnect: Locate the old ABS sensor. Carefully unplug its wiring connector.
  3. Release Wiring: Release any wire retainers securing the sensor cable from the chassis and suspension components.
  4. Remove Old Sensor: Remove the mounting bolt that secures the old sensor and carefully take off the faulty sensor.
  5. Clean Mounting Area: Clean the mounting hole and surrounding contact surface thoroughly to ensure a proper fit and connection for the new sensor.
  6. Install New Sensor: Install the new WINLINTE ABS Wheel Speed Sensor (Part Number 1J0927807D, ALS418, 5S10501) into its position.
  7. Tighten Bolt: Tighten the mounting bolt to the vehicle manufacturer's specified torque.
  8. Secure Wiring: Secure the new sensor wire using the original retainers to prevent damage from movement or contact with other components.
  9. Reconnect Electrical: Reconnect the electrical connector firmly to the new sensor.
  10. Reassemble: Refit the wheel and carefully lower the vehicle.
  11. Final Test: Clear any existing ABS fault codes using a diagnostic tool and perform a test drive to confirm proper operation of the ABS system.

6. Operating Instructions

Once installed, the ABS Wheel Speed Sensor operates automatically as part of your vehicle's ABS system. No manual operation is required. The sensor continuously monitors wheel speed and transmits data to the ABS control module. Ensure that after installation, you perform a test drive and clear any fault codes to confirm the system is functioning correctly.

7. Maintenance

The WINLINTE ABS Wheel Speed Sensor is designed for durability and minimal maintenance. However, regular inspection can help ensure its longevity and proper function:

  • Visual Inspection: Periodically inspect the sensor and its wiring for any signs of physical damage, corrosion, or loose connections.
  • Cleanliness: Keep the sensor area free from excessive dirt, debris, or road grime, which could interfere with its operation.
  • Wiring Integrity: Ensure the wiring harness is securely fastened and not rubbing against any moving parts or sharp edges.
  • Professional Check: If your vehicle's ABS warning light illuminates, or if you suspect a malfunction, have the system professionally diagnosed.

8. Troubleshooting

If you experience issues after installing the ABS Wheel Speed Sensor, consider the following common troubleshooting steps:

  • ABS Warning Light: If the ABS warning light remains on after installation, ensure all electrical connections are secure and properly seated. A diagnostic scan tool may be required to read and clear fault codes.
  • Incorrect Readings: Check for any debris or damage to the sensor tip or the tone ring (reluctor ring) on the wheel hub, as this can affect sensor accuracy.
  • Loose Connections: Verify that the sensor is firmly mounted and its electrical connector is fully engaged.
  • Wiring Damage: Inspect the entire length of the sensor wire for any cuts, pinches, or corrosion.
  • Professional Diagnosis: If basic troubleshooting does not resolve the issue, it is recommended to seek assistance from a qualified automotive technician for a thorough diagnosis.

9. User Tips

  • Always double-check the OE part number on your old sensor against the new one to ensure perfect compatibility, especially for vehicles with varying specifications.
  • When disconnecting electrical connectors, be gentle to avoid damaging the locking tabs or pins.
  • After installation, a diagnostic scan tool is often necessary to clear old fault codes from the vehicle's computer, even if the new sensor is working correctly.
  • Consider applying a small amount of dielectric grease to electrical connections to prevent corrosion and ensure a good contact.

10. Warranty and Support

10.1. Warranty Terms

This product comes with a 12-month warranty covering manufacturing defects only. The warranty does NOT cover damage caused by:

  • Improper installation
  • Misuse
  • Accident
  • Normal wear and tear
  • Unauthorized modification
  • Failure to follow instructions provided in this manual

For warranty claims, please contact customer service with your order number, product photos, and a detailed fault description.

10.2. Customer Support

For any questions or assistance, please contact our customer support team:

  • WhatsApp: +86 13600173478 (24 Hours Full-time Customer Support)
  • You can also contact us via the AliExpress order chat.

When contacting support, please provide your order number, car model, and product photos/videos to help us resolve your issue quickly.

10.3. EU Responsible Person

This product complies with EU Regulation (EU) 2019/1020 and relevant automotive safety standards. The designated EU Responsible Person is:

Company Name: Alter Agent S.R.L.

Full Address: Via Paolo Sarpi 11, 20154 Milano MI, Italy

Contact Email: cqzk6653@hotmail.com

Contact Phone: +39 3780423021

A PDF version of this user manual is available for download. Please refer to the product page for the link.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.