1. Introduction
The eletechsup SMKYF34 is a high-precision Schumann wave signal generator designed to produce frequencies ranging from 0.01Hz to 500kHz. This compact device features a clever antenna design for effective signal radiation, four expansion outputs for external antennas, and dual USB interfaces for cascading multiple units. It is equipped with an OLED display and a timer function for versatile use.
2. Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
3. Specifications
| Feature | Specification |
|---|---|
| Working Voltage | DC 5V |
| Working Power | 10W |
| Power Interface | Dual TYPE-C (use either one) |
| Default Frequency | 7.83Hz |
| Adjustable Frequency Range | 0.01Hz - 500kHz (Pure Sine Wave) |
| Timer Range | 1 minute - 99 hours |
| Display | OLED |
| Signal Voltage Amplitude | 3V |
| Audio Outputs | 4x 3.5MM AUX (4 times output capacity) |
| Dimensions | 127mm * 84mm * 21mm |
| Weight | 107g |
4. Setup
- Unpacking: Carefully remove the SMKYF34 from its packaging.
- Protective Films: Remove any protective films from the device, especially from the OLED display and acrylic casing.
- Power Connection: Connect the device to a DC 5V power supply using a Type-C cable. The device has dual Type-C ports; either can be used. A mobile phone charger with a Type-C cable is suitable. Note: A Type-C cable is not included with the product.
- Power On: Once connected to power, the device will display a loading message on the OLED screen and then show the current frequency (default 7.83Hz) and timer status.
Video 1: Demonstration of powering on the SMKYF34 and initial display.
5. Operating Instructions
5.1. Adjusting the Frequency
- Enter the desired frequency value using the numeric keypad and press the "OK" button.
- To re-enter a frequency, first press the "SET" button, then repeat the above steps.
- For example, to set 14.3Hz, press "1", "4", ".", "3", then "OK" in sequence.
5.2. Setting the Timer
The SMKYF34 has an output timer with a range of 1 minute to 99 hours.
- Pressing the "Timer" button for the first time will start a countdown according to the set time.
- Pressing the "Timer" button again will increment the timer by 1 step. Quickly pressing the "Timer" button will increment the timer by 10 steps.
- To reset the timer, press and hold the "Timer" button to clear it.
- To stop the timer, press and hold the "Timer" button.
- For example, to set the timer to 30 minutes, continuously press the "Timer" button to adjust the "Timer(H:M:S)" value to 00:30:00.
6. Enhancing the Schumann Wave Effect
The SMKYF34 offers methods to enhance the signal's reach and intensity:
6.1. Using External Antennas
The device features four 3.5mm AUX audio outputs, allowing connection to external antennas for increased output capacity and effect. Each output provides 4 times the effect of the internal antenna.
6.2. Cascading Multiple Units
Multiple SMKYF34 units can be cascaded to extend the signal's reach. This is particularly useful for creating a more immersive environment, such as for meditation.
- Cascade multiple signal generators using a DC 5V mobile phone charger for each unit.
- Place the generators around the perimeter of the desired area.
- Connect to a power source and sit in the center for meditation.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
- Storage: After use, turn off the device and store it in a dry place, away from direct sunlight and extreme temperatures. Keep it out of reach of children.
- Inspection: Periodically inspect the device and its cables for any signs of damage. Do not use if damaged.
8. User Tips
- For optimal experience, ensure the device is placed in a suitable position where the Schumann Resonance signal can be effectively experienced.
- Experiment with different frequencies within the adjustable range to find what works best for your intended use.
- Consider using external antennas or cascading multiple units for a more pronounced effect, especially in larger spaces or for specific applications like meditation.
- Always refer to this manual for instructions to ensure proper usage and to avoid any confusion regarding its functionality.
9. Troubleshooting
- Device not powering on: Ensure the Type-C power cable is securely connected to both the device and a functional DC 5V power source. Try a different Type-C cable or power adapter.
- No signal output: Verify that the frequency is set correctly and the device is powered on. If using external antennas, ensure they are properly connected to the 3.5mm AUX outputs.
- Display issues: If the OLED display is not working or shows abnormal characters, try disconnecting and reconnecting the power. If the issue persists, contact support.
- Frequency adjustment not working: Ensure you are following the correct steps for frequency adjustment (press SET, enter value, press OK). Check if the keypad buttons are responsive.
10. Warranty & Support
For any technical assistance, warranty claims, or further inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.
A detailed user manual in PDF format is available for reference. The instructions provided in this document are derived from the official user manual.
11. Frequently Asked Questions (FAQ)
- Q: What is the default Schumann frequency?
- A: The default frequency is 7.83Hz.
- Q: Can I use a regular phone charger to power the device?
- A: Yes, any DC 5V power supply with a Type-C cable is suitable.
- Q: Is a Type-C cable included?
- A: No, a Type-C cable is not included and needs to be provided by the user.
- Q: How do I know if the device is working?
- A: The OLED display will show the current frequency and timer status. You can also use an oscilloscope probe on the signal test interface to measure the output.