Wireless Remote Control Switch RF Relay Module

Contents

433MHz Wireless Remote Control Switch User Manual

1. Introduction

This manual provides essential information for the safe and effective use of your 433MHz Wireless Remote Control Switch. This device is designed to provide convenient wireless control for various applications such as gates, garage doors, lights, and other electrical systems. Please read this manual thoroughly before installation and operation.

433MHz Wireless Remote Control Switch with 10A relay

Figure 1: 433MHz Wireless Remote Control Switch with 10A relay

2. Package Contents

Please check the package for the following items:

  • 1 x RF Receiver Module (in protective casing)
  • 1 or more x Wireless Remote Control(s) (quantity depends on purchased option)
Receiver module and two remote controls

Figure 2: Receiver module and remote controls

3. Safety Information

  • This device operates at low voltage (below 50Vac or 75Vdc). However, always exercise caution when working with electrical components.
  • Ensure power is disconnected before performing any wiring or installation.
  • Do not expose the device to moisture, extreme temperatures, or corrosive environments.
  • Keep out of reach of children.

4. Setup and Installation

4.1 Wiring the Receiver Module

The receiver module requires a DC 12V power input and connects to your load (e.g., light, motor) via its relay contacts. Refer to the wiring schematic below:

DC output wiring schematic for the receiver module

Figure 3: Control DC output wiring schematic

  • Connect the DC 12V Power Input: The blue terminal is for the negative (-) connection, and the red terminal is for the positive (+) connection.
  • Connect your Load: The load should be connected to the relay terminals (typically NO - Normally Open, COM - Common, NC - Normally Closed). The diagram shows the load connected across two terminals, indicating a common setup where the relay switches the positive or negative line to the load.
  • Ensure all connections are secure and insulated.

4.2 Pairing the Remote Control

The remote control uses a learning code system. The exact pairing procedure may vary slightly, but a common method is as follows:

  1. Apply power to the receiver module.
  2. Locate the learning button on the receiver board (often a small button labeled 'LEARN' or 'CODE').
  3. Press and hold the learning button for a few seconds until an indicator LED on the receiver lights up or flashes.
  4. While the LED is active, press any button on your remote control that you wish to pair.
  5. The LED on the receiver should flash or turn off, indicating successful pairing.
  6. Test the remote control to ensure it operates the relay.
  7. To clear all paired remotes, press and hold the learning button for a longer duration (e.g., 8 seconds) until the LED indicates a reset.

5. Operating Modes

The receiver module supports several operating modes, which determine how the relay responds to remote control commands. Mode selection is typically done via jumpers or a dedicated button on the receiver board (refer to specific markings on your board if available).

  • Momentary Mode: The relay is active only while the remote control button is pressed and held. It deactivates upon release.
  • Toggle Mode: Pressing the remote control button once activates the relay. Pressing the same button again deactivates the relay.
  • Latched Mode: (For single-channel, often means one button turns ON, another turns OFF, or for multi-channel, one button activates its relay while deactivating others). For a 2-button remote with a single relay, this might mean button A turns ON, button B turns OFF.
  • Time Delay Mode: Pressing the remote control button activates the relay for a preset duration (e.g., 5 seconds, 10 seconds, 15 seconds), after which it automatically deactivates.

6. Maintenance

6.1 Remote Control Battery Replacement

The remote control is powered by a 3V Coin Cell Button Battery. If the remote's range decreases or it stops responding, the battery may need replacement.

  • Carefully open the remote control casing.
  • Note the polarity of the existing battery.
  • Remove the old battery and insert a new 3V Coin Cell Button Battery (e.g., CR2032) with the correct polarity.
  • Close the remote control casing securely.

7. Troubleshooting

  • Remote not responding:
    • Check the remote control battery.
    • Ensure the remote is within the effective operating range.
    • Re-pair the remote control with the receiver module.
  • Receiver not activating the load:
    • Verify the DC 12V power supply to the receiver.
    • Check all wiring connections to the load and power supply.
    • Ensure the remote control is successfully paired.
    • Confirm the operating mode is set correctly.
  • Reduced remote control range:
    • Replace the remote control battery.
    • Ensure there are no significant obstructions (thick walls, metal structures) between the remote and receiver.
    • Avoid sources of strong RF interference.

8. Specifications

8.1 Transmitter (Remote Control)

FeatureSpecification
Operating Frequency433MHz
Power Source3V Coin Cell Button Battery (included)
MaterialPVC
Buttons2
Dimensions59mm x 28mm x 8mm
Operating Voltage3V
Operating Current12mA
Transmitting Power10mW
Modulation ModeASK (AM)
Encoding TypeLearning Code (1527)
Transfer Distance20-50 meters (open area)

8.2 Receiver Module

FeatureSpecification
RF Working ModeSuperheterodyne Reception
Modulation ModeASK
Working ModesMomentary, Toggle, Latched, Time Delay (5s, 10s, 15s)
Input VoltageDC 5V ~ 60V (Commonly DC 12V)
RF Frequency433MHz
Quiescent Current5mA
Receiving Sensitivity>97dbm
Remote Control Range>100m (Free Space)
Wired ConnectionFixed Wiring Pillar
Decoding ModeMCU Software Decoding
Max Current10A
CertificationCE, RoHS
Dimensions (approx.)40mm x 25mm (module in case)
Dimensions of the receiver module

Figure 4: Approximate dimensions of the receiver module

9. User Tips

  • Always test the remote control's range in your specific environment before final installation to ensure reliable operation.
  • Consider the placement of the receiver module to minimize interference and maximize signal reception.

10. Warranty and Support

For any issues, questions, or support needs regarding your 433MHz Wireless Remote Control Switch, please contact your seller or the point of purchase. Keep your purchase records for warranty claims.

11. Product Media

11.1 Product Overview Video

Video 1: Unboxing and overview of the receiver module and remote control.

11.2 Application Examples

Applications of the remote control switch including gates, lights, and air conditioners

Figure 5: Various applications for the wireless remote control switch.

Remote control applications for lighting, electric fans, door systems, and gates

Figure 6: Common uses for the remote control in home automation.

11.3 Wireless Features

Wireless RF Remote Control features: 360 degree omnidirectional, signal penetrates walls, manual and remote synchronous operation

Figure 7: Key features of the wireless RF remote control.

Remote control supports wide range up to 100 meters in open area

Figure 8: Wide operating range of the remote control.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.