OPEL LED Car Door Welcome Light

Contents

LED Car Door Welcome Light User Manual

Model: LED Car Door Welcome Light

1. Product Overview

The LED Car Door Welcome Light is a wireless, battery-powered projector designed to display your car's logo on the ground when the car door is opened. It enhances the aesthetic appeal of your vehicle and provides a welcoming light feature.

Two LED Car Door Welcome Lights projecting Opel logos on the ground next to a car.
The LED Car Door Welcome Light projects your car's logo onto the ground.
Close-up of the LED Car Door Welcome Light projector unit with an Opel logo keyfob.
The compact projector unit.

2. Specifications

Feature Detail
Material ABS
Power Output 7W
Dimensions (L x W) 6.6cm x 6.4cm
Working Voltage 4.5V
Lamp Type High Brightness LED
Item Color Black
Power Supply 3 x AAA Batteries (not included)
LED Color Temperature 6000 K
Package Dimensions (L x W x H) 17cm x 17cm x 3cm
Package Weight 0.076 kg
Diagram showing the dimensions of the projector unit as 6.6cm by 6.4cm.
Product dimensions.

3. Setup and Installation

This device is designed for easy, non-destructive installation without the need for drilling. Follow these steps for proper setup:

  1. Prepare the Device: Open the battery compartment and insert 3 AAA batteries (not included) into each projector unit, ensuring correct polarity.
  2. Clean the Installation Area: Thoroughly clean the area on the car door where the projector will be attached. Ensure it is dry and free of dust or grease for optimal adhesive performance.
    A hand cleaning the car door panel where the welcome light will be installed.
    Step 1: Clean the installation area.
  3. Attach the Projector Unit: Peel off the adhesive backing from the projector unit. Stick the projector unit firmly to the lower part of the car door panel. Position it as low as possible without interfering with the door's opening or closing mechanism.
    A hand peeling off the adhesive backing from the projector unit.
    Step 2: Peel off adhesive backing.
    A hand pressing the projector unit onto the car door panel.
    Step 3: Stick the projector unit to the car door.
  4. Install the Magnet: Attach the small magnet to the car door sill, directly below the projector unit. Ensure the magnet is aligned with the sensor on the projector unit. This alignment is crucial for the automatic on/off function.
    A hand installing the magnet on the car door sill, aligning it with the projector.
    Step 4: Install the magnet on the door sill.
    Diagram showing the correct alignment of the projector unit and the magnet.
    Ensure proper alignment between the projector and the magnet.
  5. Test Functionality: Open and close the car door to verify that the logo projects when the door is open and turns off when the door is closed.
    Image showing the completed installation of the welcome light on a car door.
    Installation complete.

For a visual guide, please watch the installation video:

Product demonstration and installation guide.

4. Operating Instructions

The LED Car Door Welcome Light operates automatically based on the proximity of the magnet installed on the door sill.

  • When the car door is opened, the projector unit moves away from the magnet, activating the sensor and illuminating the projected logo on the ground.
  • When the car door is closed, the projector unit moves closer to the magnet, deactivating the sensor and turning off the projected logo.
  • The device is designed for high efficiency and energy saving, producing no noise or electronic interference.
  • Some upgraded versions may feature intelligent sensing that automatically turns off the light in strong sunlight to conserve battery life.
Comparison image showing a car door before and after installation of the welcome light, highlighting the projected logo.
Before and After: The projected logo provides a welcoming light.

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the surface of the projector unit and the lens. Avoid using abrasive cleaners or solvents that could damage the device.
  • Battery Replacement: When the projected light appears dim or stops working, it's time to replace the batteries. Open the battery compartment, remove the old AAA batteries, and insert new ones, ensuring correct polarity.
  • Adhesive Check: Periodically check the adhesive to ensure the projector and magnet remain securely attached to the car door and sill. Reapply or replace adhesive if necessary.

6. Troubleshooting

  • Light does not turn on:
    • Check if batteries are inserted correctly and are not depleted.
    • Ensure the magnet is properly aligned with the sensor on the projector unit. The gap between the magnet and the sensor should be minimal when the door is closed.
    • Verify that the power switch on the projector is in the 'ON' position.
  • Light is dim:
    • Replace the AAA batteries with new ones.
  • Light does not turn off when door is closed:
    • Check the alignment of the magnet and the projector's sensor. They must be close enough for the sensor to detect the magnet.
    • Ensure no obstructions are preventing the magnet from coming into close contact with the sensor.
  • Projector falls off:
    • Ensure the installation surface was clean and dry before applying the adhesive.
    • Reapply with stronger automotive-grade double-sided adhesive tape if needed.

7. User Tips

  • Check Compatibility: Before purchasing or installing, verify that your car door's interior panel and sill have a flat enough surface for proper adhesion and alignment of both the projector and the magnet. Some car models, like the Opel Corsa D, may have door curvatures that prevent proper installation.
  • Battery Quality: Use high-quality alkaline AAA batteries for longer performance and consistent light output.
  • Optimal Placement: Experiment with the exact placement of the projector and magnet to find the best balance between projection clarity and reliable automatic on/off functionality.

8. Warranty and Support

For detailed warranty information or further assistance, please refer to the official user manual PDF provided by the seller, or contact the seller directly through the platform where the product was purchased.

A digital version of the user manual can be found here: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.