BRIGHTWIN BRT 420SG-D2

Contents

BRIGHTWIN BRT 420SG-D2 Current Signal Generator User Manual

Model: BRT 420SG-D2

1. Introduction

The BRIGHTWIN BRT 420SG-D2 is a versatile current signal generator and display meter designed for industrial control applications. It supports both manual operation and RS485 remote control, making it suitable for various uses such as valve control, inverter control, and constant pressure control systems.

Main Features:

  • Current signal generator and display meter all in one.
  • Standard 35mm DIN Rail-mounting shell for easy installation.
  • Supports 24VDC power supply.
  • Manual operation and output accuracy calibration.
  • Adjustable 6-level LED display luminance.
  • Equipped with MODBUS RS485 communication for remote control.
  • Default 4-20mA output, adjustable to 0-20mA, 0-22mA, or 0-24mA via button.
Front view of the BRIGHTWIN BRT 420SG-D2 signal generator with a red digital display showing '20.0' and a rotary knob.
Figure 1: Front view of the BRT 420SG-D2 Signal Generator.

2. Safety Warnings

  • This signal generator requires a high voltage power supply. Always remove power supply first before performing any wiring connections.
  • DO NOT connect input/output wires without removing power supply to avoid high voltage injury.
  • Always operate the device according to this user manual. Do not exceed the rated limited values, as this may cause permanent damage to the device.

3. Product Overview and Dimensions

The BRT 420SG-D2 is housed in a compact DIN rail-mountable enclosure, designed for easy integration into control panels.

Side view of the BRIGHTWIN BRT 420SG-D2 signal generator, highlighting the DIN rail mounting clips.
Figure 2: Side view showing DIN rail mounting clips.
Dimensional drawing of the BRIGHTWIN BRT 420SG-D2 signal generator with measurements in millimeters.
Figure 3: External shell dimensions (L x W x H): 87.50 x 36.50 x 58.70 mm.

4. Technical Specifications

Parameter Specification
Power Supply 24VDC (±10%)
Power Consumption <2W
Current Signal Output Default 4-20mA (adjustable to 0-20mA, Max 0-22mA)
Output Error Grade <0.05mA, load sampling resistance <500 Ω
Output Adjusting Accuracy 0.1mA
Input Feedback Accuracy <0.05mA, internal sampling resistance 10 Ω
Display Mode Actual current value (4.0-20.0mA), 0.0-100 (%), 0.0-50.0(Hz)
RS485 Communication Standard MODBUS-RTU
External Shell Size (L x W x H) 87.50 x 36.50 x 58.70mm
Operating Temperature 0-40°C, <80% R.H.
Battery Included No
Certification CE, RoHS

5. Installation and Wiring

Proper wiring is crucial for the safe and correct operation of the signal generator. Refer to the diagrams below for terminal descriptions and wiring configurations.

Wiring Terminals Description:

  • GND (Signal output GND-): Signal output negative.
  • OUT (Signal output +): Signal output positive.
  • VCC (24VDC power supply +): Positive terminal for 24VDC power supply.
  • GND (Power supply GND-): Negative terminal for power supply, common ground with signal input GND.
  • ACL (220VAC power supply L): Live wire for optional 220VAC power supply.
  • ACN (220VAC power supply N): Neutral wire for optional 220VAC power supply.
  • B-/A+ (RS485 communication B-/A+): Terminals for RS485 communication.
Detailed wiring diagrams for 4-20mA output, DC24V power, RS485 communication, and AC220V power supply options.
Figure 4: Wiring diagrams for various configurations.

6. Operation Instructions

6.1. Knob Functions Definition

  • [Confirm/OK]: Press the knob.
  • [+/Add]: Rotate the knob in a clockwise direction to increase values.
  • [-/Subtract]: Rotate the knob in a counter-clockwise direction to decrease values.

6.2. Parameters Setting

  1. In normal operating status, long press the knob for 2 seconds to enter parameter setting mode. The LED screen will display "F01".
  2. Rotate the knob to navigate through referential parameter setting codes from F01 to Fnd.
  3. Press down the knob to enter the parameter setting status for the selected code. Then, rotate the knob to change the parameter value to your desired setting. Refer to Table 1.1 for parameter definitions.
  4. After selecting the value, press the knob again to save the parameter setting.

6.3. Referential Code Definition (Table 1.1)

Referential Code Parameters Setting Value Description Default Setting
F01Fine or rough adjustment0: Rough adjustment (F02 changes add/sub value times.)
1: Fine adjustment (F03 changes add/sub value times.)
1
F02Add or subtract value in rough adjustment per pulse1 to 50: output value changing step per pulse. No decimal points. Rotating knob one turn (360 degrees) equals 20 pulses. Can be ten times 10 x (1 to 50).1
F03Add or subtract value in fine adjustment per pulse1 to 50: output value changing step per pulse. No decimal points. Rotating knob one turn (360 degrees) equals 20 pulses.1
F04Pressing knob functions0: Manually save output value (fixed startup value)
1: Quickly switch between fine/coarse adjust (saves automatically in 3s)
2: Output ON/OFF (saves automatically in 3s)
3: Quickly reset to min. value (saves automatically in 3s)
1
F05Output range0: 0-20mA, 1: 4-20mA, 2: 0-22mA, 3: 0-24mA, -1: User-defined output0
F06Customized min. output0-24.0mA0
F07Customized max. output0-24.0mA10.0
F08Display mode0: Actual current value display
1: 0-100.0 percentage display
2: 0-50Hz display
3: 0-90° display
4: 0-130 display
5: 0-150 display
6: 0-250 display
7: 0-400 display
8: 0-600 display
-1: User-defined output
0
F09Customized min. display value-199 to 999, decimal point setting in F110
F10Customized max. display value-199 to 999, decimal point setting in F11200
F11Decimal point setting0-3 (0/1: None, 2: 99.9, 3: 9.99)2
F12Slave Device ID1-1271
F13Baud rate value0: 2400, 1: 4800, 2: 9600, 3: 19200, 4: 38400, 5: 576002
F14Check-sum0: 8-N-1, 1: 8-N-2, 2: 8-ODD-1, 3: 8-EVEN-12
F15LED luminance adjustment0 to 7 (7 max. luminance level)1
F164mA output calibration-999 to +999. Not recommended if output accuracy is normal. For professionals only.--
F1712mA output calibrationFor professionals only.--
F1820mA output calibrationFor professionals only.--

6.4. Fine/Coarse Adjustment Setting Examples

The encoder knob rotates 20 grids per turn. F02 and F03 define the step size for rough and fine adjustments.

Example Settings F01 F02 F03 Explanation
0-20mA display 0-20.0, knob adjustment 1 turn0X1Set fine tuning, with a change of 1mA per grid
0-20mA display 0-20.0, knob adjustment 5 turns1X2Set fine-tuning 2, one grid change of 0.2mA
4-20mA display 0-100, knob adjustment 1 turn1X5Set fine adjustment 5, with a change of 0.5mA in one grid

6.5. Example of Setting Output Range and Display Scale

The following table provides examples for configuring output range and display scale using parameters F05 to F11. 'X' indicates that the parameter does not need to be set or its setting does not affect the outcome for that specific example.

Example Settings F05 F06 F07 F08 F09 F10 F11
0-20mA display 0-20.0 (current value)0XX0XXX
0-20mA display 0-100 (% percentage)0XX1XXX
4-20mA display 0-100 (% percentage)1XX1XXX
4-20mA display 0-50 (HZ)1XX2XXX
4-20mA display 0-90 (° angle)1XX3XXX
4-20mA display 0-500 (speed)1XX-105000
4-20mA display 0-1.60 (MPa pressure)1XX-101603
4-20mA display -40 to 80 (°C temperature)1XX-1-40800
3-21mA display 3-21.0-13.021.00XXX
0.5-21.5mA display -20 to 200-10.510.5-1-202000

Note: Due to the inability to display 1000 with 3 digital tubes, A00 is used instead of displaying it.

Signal generator connected to an LB02 process calibrator, showing a 20.000mA output.
Figure 5: Signal generator outputting 20.000mA, verified by a process calibrator.
Signal generator connected to an LB02 process calibrator, showing a 12.000mA output.
Figure 6: Signal generator outputting 12.000mA, verified by a process calibrator.
Signal generator connected to an LB02 process calibrator, showing a 0.000mA output.
Figure 7: Signal generator outputting 0.000mA, verified by a process calibrator.

7. MODBUS RS485 Communication

The BRT 420SG-D2 supports standard MODBUS RTU protocol for remote control and data acquisition.

  • The signal generator's meter address is 1-127 (factory default setting is 1).
  • Baud rates supported: 2400-115200 (factory default setting is 9600).
  • Checksum: None.
  • 120Ω terminal resistance is NOT embedded in RS485 ports. For long-distance transmission, users need to add external terminal resistance for stable data transmission.
  • It is recommended to use high-quality shielded twisted pair cable to enhance data communication anti-interference capability.

7.1. MODBUS Command Format

Field Size Description
RS485 slave address1 byte
Functional code1 byte03 or 06
DataN byte
CRC check2 byteStandard CRC16, initial value 0xFFFF

7.2. 03 Inquire Multiple Register Command Example

Example: Inquire 3 registers starting with address 0.

  • Send: 01 03 00 00 00 06 C5 CB
  • Return: 01 03 0C 00 00 00 00 00 00 00 21 75

7.3. 06 Set a Single Register Command Example

Example: Set register 1 value to 100, return command directly.

  • Send: 01 06 00 01 00 64 D9 E1
  • Return: 01 06 00 01 00 64 D9 E1

7.4. Register Table

Register Address Description Read/Write Notes
0None--Some PLC data address starts from 1
1Current value displayR/WNo decimal point, E.g: 10=0.1mA, 1000=20.00mA
3None--

Note: Receiving one packet of data successfully will cause the communication LED indicator to flash once.

Table detailing MODBUS command format and register table for RS485 communication.
Figure 8: MODBUS Command Format and Register Table.

8. Calibration

8.1. 4mA Accuracy Calibration (F16)

  1. First, adjust the BRT 420SG-D2 signal generator to 4mA display mode.
  2. Connect a precision mV measuring multimeter to the BRT 420SG-D2 signal generator's output (+ and -) terminals.
  3. Adjust the BRT 420SG-D2 signal generator knob until the precision multimeter accurately displays 4.0mA.
  4. Finally, press down the BRT 420SG-D2 signal generator knob to save the parameter setting.

Important: When performing F16, F17, or F18 output precision calibration, a high-precision multimeter is required, connected to the signal generator's output terminals. For F16, F17, F18, adjust the output to make the signal generator display 4mA, 12mA, and 20mA respectively, then proceed with calibration.

9. Maintenance

  • Keep the device clean and free from dust and moisture.
  • Avoid exposing the device to extreme temperatures or direct sunlight.
  • Do not use harsh chemicals or abrasive cleaners on the device. Use a soft, dry cloth for cleaning.
  • Ensure all wiring connections are secure and free from corrosion.

10. Troubleshooting

  • No Display/No Power: Check the 24VDC power supply connection and ensure it is within the specified voltage range (24VDC ±10%). Verify wiring according to the installation section.
  • Incorrect Output: Verify the parameter settings (F01-F11) are correct for your desired output range and display scale. Perform calibration (F16, F17, F18) if necessary, using a precision multimeter.
  • Unstable Output: Check for loose wiring connections. Ensure the load sampling resistance is within the specified range (<500 Ω).
  • RS485 Communication Issues: Verify the slave device ID (F12) and baud rate (F13) settings. Ensure high-quality shielded twisted pair cable is used. For long-distance communication, add external 120Ω terminal resistance.
  • Device Damage: If the device shows signs of physical damage or malfunction not covered by basic troubleshooting, discontinue use and contact technical support.

11. User Tips

  • For critical applications, always double-check the output with a calibrated multimeter after setting parameters.
  • When integrating with PLC systems, ensure the MODBUS register addresses align with your PLC's configuration, noting that some PLC data addresses start from 1.
  • Utilize the adjustable LED luminance (F15) to optimize visibility in different lighting conditions.

12. Support and Resources

For further technical assistance or inquiries, please contact:

The specifications are subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.