1. Introduction
This manual provides essential information for the safe and effective use of your HJC FURION 3.0 BULLES MTB Road Cycling Helmet. Please read it thoroughly before using the helmet and retain it for future reference.
This helmet is designed for road and mountain biking, offering a blend of ultralight construction and aerodynamic performance for both men and women.
2. Safety & Warnings
WARNING:
- This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
- Always ensure the helmet is properly fitted and secured before riding.
- No helmet can protect the wearer against all foreseeable impacts.
- Replace your helmet after any significant impact, even if visible damage is not apparent.
- Do not modify or remove any original components of the helmet.
- Avoid exposing the helmet to extreme temperatures or corrosive substances.
This product complies with the essential health and safety requirements set out in Regulation (EU)2016/425 and meets the EN 1078:2012+A1:2012 standard.
3. Product Features
- Type: Integrally-molded Helmet
- Material: ABS
- Air Vents: 8 - 15 for optimal ventilation
- Design: Aerodynamic for reduced drag
- Weight: Ultralight construction (approx. 247g for M, 272g for L)
- Adjustable Fit System: Dial-based retention system for a secure and comfortable fit.
- Adjustable Straps: Chin straps with buckle for personalized adjustment.
4. Setup Instructions
Follow these steps to ensure a proper and safe fit for your helmet:
- Placement: Place the helmet squarely on your head, ensuring it covers your forehead. It should sit level, not tilted back or forward.
- Adjusting the Retention System: Locate the dial at the back of the helmet. Turn the dial clockwise to tighten the fit or counter-clockwise to loosen it until the helmet feels snug but comfortable, without excessive pressure points.
- Adjusting the Chin Straps:
- Slide the strap adjusters to position the straps so they form a 'V' shape just below your ears.
- Fasten the buckle securely under your chin.
- Tighten the chin strap until it is snug. You should be able to open your mouth wide, but the strap should not be loose enough to allow the helmet to shift significantly.
- Ensure the excess strap is secured to prevent flapping.
- Final Check: With the chin strap fastened, try to move the helmet from side to side and front to back. If it moves more than an inch in any direction, readjust the retention system and straps.
5. Operating Instructions
Once your helmet is properly fitted, you are ready to ride. Always wear your helmet when cycling to ensure maximum protection. The helmet is designed to absorb impact energy by partially destroying the shell and liner. Therefore, it is crucial to replace your helmet after any impact, even if it appears undamaged.
6. Maintenance
- Cleaning: Clean the helmet shell with a soft cloth, mild soap, and water. Avoid harsh chemicals, solvents, or abrasive cleaners, as these can damage the helmet's materials and compromise its protective capabilities.
- Liner Care: The internal padding can often be removed and hand-washed with mild soap and water. Allow it to air dry completely before reinserting.
- Storage: Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Do not store it near heat sources or in a car on a hot day, as this can damage the EPS foam liner.
- Inspection: Regularly inspect your helmet for any signs of wear, cracks, or damage to the shell, straps, or retention system. If any damage is found, replace the helmet immediately.
7. Troubleshooting
- Helmet feels loose or shifts during riding:
- Ensure the rear retention dial is tightened sufficiently and the chin straps are snug. Re-adjust both until the helmet is stable.
- Straps are uncomfortable or rub against ears:
- Adjust the strap dividers to ensure the 'V' shape sits comfortably below your ears, and the chin strap is centered.
- Helmet causes pressure points:
- Loosen the retention system slightly. If pressure persists, the helmet size or shape may not be suitable for your head. Consider trying a different size or model.
8. Specifications
| Attribute | Value |
|---|---|
| Brand Name | HJC |
| Model Number | Raceday Road mtb met red bull (002) |
| Type | Integrally-molded Helmet |
| Material | ABS |
| Air Vents | 8 - 15 |
| Weight (g) | 272 (for size L) |
| Age Group | (Adults) Men |
| Sizes Available | M (54-58cm), L (55-62cm) |
| Certification | EN 1078:2012+A1:2012 |
| Package Length | 32 cm |
| Package Width | 23 cm |
| Package Height | 23 cm |
| Package Weight | 0.41 kg |
| Origin | Mainland China |
9. User Tips
- The helmet offers a good fit and shape, and users have noted it pairs well with cycling glasses.
- Appreciated for its lightweight design and quality paint finish.
- Pay close attention to the fit of the rear tightening dial and the under-ear strap parts for optimal comfort and security.
- Ensure straps are properly adjusted to adapt to your face's morphology for a secure and comfortable fit.
- Note that this helmet does not explicitly state the inclusion of a MIPS (Multi-directional Impact Protection System) layer. Users prioritizing this feature should consider this.
10. Frequently Asked Questions (FAQ)
- Q: Are helmets with bull patterns available?
- A: Yes, helmets with bull patterns (e.g., Red Bull Racing) are available. Please refer to the product images for examples.
- Q: What are the available helmet sizes?
- A: The helmet is available in sizes M (54-58cm) and L (55-62cm).
- Q: Is there a user manual in PDF format?
- A: Yes, a user manual in PDF format is available. You can view it here.
11. Warranty & Support
For any inquiries or support regarding your HJC FURION 3.0 BULLES helmet, please contact the manufacturer or the authorized EU representative:
Manufacturer:
RUIAN LEI PENG WEI TRADING CO., LTD.
Address: FLOOR 2, NO.6, DOCK SOUTH ROAD, QIANBUVILLAGE, XINCHENG STREET, RUIAN CITY, ZHEJIANG, CHINA
E-mail: willing88@126.com
Phone: 18106757030
EU Representative:
SUCCESS COURIER SL
Address: CALLE RIO TQRMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, Spain, 28947.
Phone: +34910602659
E-mail: successservice2@hotmail.com