IKSLED 7036-Touch

Contents

IKSLED AC-7036-T 400W Touch Sensor Switch User Manual

Model: AC-7036-T

1. Product Overview

The IKSLED AC-7036-T is a high-power detachable touch sensor switch designed for controlling lighting in various applications such as wardrobes, cabinets, display cases, and kitchen under-cabinet lights. This switch supports a maximum load of 400W, making it suitable for larger LED panels and multiple light strips. Its detachable design features a sleek stainless steel touch button connected by a cable, allowing the main control box to be discreetly hidden while the elegant touch panel remains visible for easy operation.

The switch operates on a simple touch logic: touch once to turn the light ON, and touch again to turn the light OFF. It is compatible with a wide voltage range of AC 100-240V (50/60Hz).

Touch Sensor Switch with hand touching the button
Figure 1: IKSLED AC-7036-T Touch Sensor Switch in operation.

2. Safety Precautions

Please read and understand all safety instructions before installation and use.

  1. High Voltage Warning: The sensor cable and internal circuit board carry high voltage. Always disconnect the main power supply before installation, removal, or maintenance to avoid electric shock.
  2. Do Not Disassemble: Never disassemble the sensor housing or touch the internal circuit board directly, as this may cause electric shock or device damage. Disassembling the unit will void the warranty.
  3. Load Limitation: Do not exceed the total power of 400W. Overloading will burn out the device.
  4. Environmental Requirements: Avoid installing the switch in damp, high-temperature, or strong electromagnetic interference environments to ensure stable operation and prevent damage.
Safety warning: Do not disassemble the sensor
Figure 2: Important safety warning against disassembling the sensor.

3. Specifications

FeatureSpecification
Brand NameIKSLED
Model Number7036-Touch (AC-7036-T)
Product NameAC7036T- Touch Sensor Control Switch
Switch TypeTouch On/Off Switch
FunctionTouch-light on. Touch again-light off. (No dimming)
TypeDetachable Probe Type
Input VoltageAC 100V-240V (50/60Hz)
Max Power Load400W
Rated Current~1.81A (at 220V) / ~1.82A (at 110V)
Main Controller Dimensions76mm (L) x 36mm (W) x 23mm (H)
Touch Probe Dimensions17mm (Diameter) x 11mm (Height)
MaterialPlastic (Controller), Brushed Stainless Steel (Probe)
CertificationSAA, RoHS, LVD, EMC, CE
OriginMainland China
ApplicationLED Cabinet Lights, Closet/Pantry Lighting, Under-Counter Kitchen Lights, Wardrobe/Cupboard Lights
Product Size diagram showing dimensions of the main module and touch button
Figure 3: Dimensions of the main controller unit and touch probe.

4. Setup

4.1. Wiring Instructions

Ensure the main power supply is OFF before proceeding with any wiring.

Terminal Definitions:

  • L (Lo): Live wire output (connect to load live wire)
  • Li: Live wire input (connect to mains live wire)
  • Ni: Neutral wire input (connect to mains neutral wire)
  • No (N out): Neutral wire output (connect to load neutral wire)

Typical Wiring Methods:

  1. Direct AC Load Drive (e.g., 100-240V lamps):
    • Connect mains live wire to Li.
    • Connect mains neutral wire to Ni.
    • Connect load live wire to Lo.
    • Connect load neutral wire to No.
  2. Low-Voltage Lamp Drive (e.g., 12V/24V LED strips):
    • First, connect the constant voltage power adapter to the mains.
    • Then, connect the adapter output to the LED strip.
    • Connect the controller to the adapter using the direct AC load drive method described above to achieve door-controlled on/off for the low-voltage strip.
Detailed Connection Diagram for LED and energy-saving lamps
Figure 4: Wiring diagram for various load types (100-240V lamps, 12V/24V lamps with adapter, AC1100V-240V load).

4.2. Installation Steps

  1. Power Off: Always turn off the main power supply at the circuit breaker before installation and confirm no voltage is present using a voltage tester.
  2. Install the Sensor Probe: Drill a 17mm diameter mounting hole in the desired location (e.g., cabinet door or body). Insert and secure the touch sensor probe into the hole.
  3. Mount the Controller: Install the main controller unit inside the cabinet or desired enclosure. Use screws through the reserved mounting holes. Ensure adequate ventilation around the controller to avoid blocking heat dissipation.
  4. Make Wiring Connections: Follow the wiring instructions in Section 4.1 to connect the mains and load to the corresponding terminals. Ensure all connections are secure, tight, and free of looseness. Organize cables neatly to avoid squeezing, tangling, or creating short circuits.
  5. Power On and Test: Restore power to the circuit. Touch the sensor to turn the light ON, and touch it again to turn the light OFF. Verify proper operation.
Example of drilling installation for the touch sensor in a kitchen cabinet
Figure 5: Example of drilling installation for the touch sensor.

5. Operating Instructions

The IKSLED AC-7036-T touch sensor switch operates with a simple ON/OFF function:

  • To Turn ON: Lightly touch the stainless steel sensor probe. The connected lights will illuminate.
  • To Turn OFF: Lightly touch the stainless steel sensor probe again. The connected lights will turn off.

This switch does not support dimming functions.

Touch Switch On/Off states
Figure 6: Visual representation of the touch switch in Off and On states.
Video 1: Demonstration of the touch on/off functionality of the switch.

6. Maintenance and Care

  • Connection Check: Regularly check that all wiring connections are secure to prevent poor contact or overheating due to looseness.
  • Cleaning: Keep the device surface clean to avoid dust accumulation that may affect heat dissipation and sensing sensitivity. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
  • Abnormal Operation: If the device shows abnormal heat, odor, or smoke, immediately disconnect the power supply, stop using it, and contact a qualified professional for inspection and repair.

7. Troubleshooting

  • Light does not turn on when touched:
    • Possible causes: Incorrect or loose wiring, load power exceeding 400W, or power supply not connected.
    • Solutions: Check and rewire all connections, ensure the total load power does not exceed 400W, and confirm the main power supply is active.
  • Light remains on continuously:
    • Possible causes: Sensor probe malfunction or controller malfunction.
    • Solutions: Disconnect power, check the sensor probe for any visible damage. If the issue persists, the controller may need replacement.
  • Light flickers:
    • Possible causes: Incompatible load type (e.g., some dimmable lamps are not compatible) or loose wiring connections.
    • Solutions: Replace with a compatible LED/energy-saving lamp (non-dimmable) or tighten all terminal connections.

8. User Tips

No specific user tips were available for this product. Always ensure proper installation and adhere to safety guidelines for optimal performance and longevity of your touch sensor switch.

9. Warranty and Support

This IKSLED Touch Sensor Switch comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For warranty claims, technical support, or any inquiries regarding your product, please contact your original retailer or the IKSLED customer service department with your purchase details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.