1. General Introduction
The X100MAX Auto Key Programmer is a professional key programming device, based on the Android operating system. It supports multi-language switching and is suitable for different countries and regions.
1.1 Tablet Components

Figure 1: XTOOL X100 MAX Tablet Components
- Type-C Port
- Reset Hole
- Power Button
- Microphone
- Camera
- Speaker
- Nameplate
- Tablet Holder
1.2 VCI Box Components

Figure 2: XTOOL X100 MAX VCI Box Components
- Screen
- DB15 Port
- Nameplate
- USB Type-B Port
2. Safety Precautions
Please read this user manual carefully before using the Auto Key Programmer, referred to as the "Programmer" throughout this document. When reading the manual, please pay attention to the words "Note" or "Caution", and read them carefully for appropriate operation.
2.1 Operation Instructions
For safe operation, please follow the instructions below:
- Keep the device away from heat or fumes when in use.
- If the vehicle battery contains acid, please keep your hands and skin or fire sources away from the battery during testing.
- The exhaust gas of the vehicle contains harmful chemicals. Please ensure adequate ventilation.
- Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to the high temperatures reached.
- Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle from moving when the engine starts.
- Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the Diagnostic Computer.
- Do not switch off the power or unplug the connectors during testing. Doing so may damage the ECU (Electronic Control Unit) and/or the Diagnostic Computer.
2.2 Cautions!
- Avoid shaking, dropping or dismantling the Programmer as it may damage the internal components.
- Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the Programmer.
- Do not use excessive force;
- Do not expose the screen to strong sunlight for a long period.
- Please keep the Programmer away from water and moisture.
- Store and use the Programmer only within the temperature ranges identified in the Technical Specifications section.
- Keep the unit away from strong magnetic fields.
2.3 Precautions for Diagnosis
- The voltage range on the car: +9~+36V DC;
- When testing some special functions, the operator must operate according to the prompts and meet the test conditions. For some models [special functions], the conditions that need to be met are: engine water temperature 80°C~105°C, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
- The electronic control systems of different models are very complicated. If you encounter situations where it is impossible to test or a large amount of test data is abnormal, you can search for the ECU of the vehicle and select the menu for the model on the ECU nameplate;
- If the vehicle type or electronic control system to be tested is not found in the diagnostic function, please upgrade the vehicle diagnostic software to the latest version using the Updates menu or consult the XTOOL technical service department;
- Only wiring harnesses provided by XTOOL and designed for the device are permitted to be used with this device to avoid damage to the vehicle or the device;
- When running a Diagnostics function, it is forbidden to shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.
3. Setup
3.1 Vehicle Connection

Figure 3: Vehicle Connection Steps
- Press and hold the Power button to turn on the tablet.
- Select App language and start the activation. Follow the hints to complete the activation.
- Connect the DB15 connector of the main cable to the VCI box.
- Plug the OBDII-16 connector of the main cable into the vehicle's DLC port.
- When the VCI box gets powered on, the tablet will automatically search for it and make a WiFi connection.
- Your tablet is now ready.
4. Operating Instructions
4.1 Vehicle Selection
The Programmer supports the following 3 ways to access the smart diagnostics system:
- AUTO SCAN: Supports automatic reading of vehicle VIN code. Tap "AUTO SCAN" on the diagnosis system entrance. Ensure the car and device are well connected.
- MANUAL INPUT: Supports manual input of car VIN code. Ensure the 17 characters are correct for accurate test results.
- SELECT VEHICLE BY AREA: Choose a car brand by selecting the appropriate region at the top of the screen, then select the vehicle model.
Note: If your model is not recognized, try the following steps:
- UPDATE all software, and check whether the APP is updated in [Settings].
- Click Diagnosis on the main menu to enter the selection menu, manually select the engine system to read the ECU information, and confirm whether the VIN can be read.
- Contact the XTOOL technical team to provide the VIN code to confirm whether the model supports automatic identification of VIN.
4.2 Diagnosis Functions
Diagnostics functions supported by the Programmer include:
- Read ECU Information: Reads ECU version information (software/hardware versions, models, production date, part numbers).
- Read/Clear Trouble Code: Reads and clears Diagnostic Trouble Codes (DTCs).
- Read Live Data: Displays real-time information from various sensors (PIDs). You can search for PIDs, graph data, and combine multiple graphs.
- Actuation Test (Bi-Directional Control): Sends and receives information between the device and vehicle control modules to test actuating components.
4.3 Special Functions (42+ Resets)
The X100 MAX supports over 42 special reset functions to quickly access vehicle systems for scheduled services and maintenance. Functions vary by vehicle; please check compatibility first.

Figure 4: Overview of 42+ Hottest Resets Functions
- ABS BLEEDING: Performs ABS bleeding to restore brake system sensitivity when air is present.
- OIL RESET: Resets the engine oil life system after an oil change.
- EPB (Electronic Parking Brake) Reset: Resets the electronic parking brake system and brake pads.
- SAS (Steering Angle Sensor) Calibration: Calibrates the steering angle sensor after replacement or repair.
- BMS RESET (Battery Management System): Evaluates battery charge state, monitors current, registers battery replacement, and activates rest state.
- INJECTOR CODING: Writes the identification code of the fuel injector into the ECU.
- DPF REGENERATION (Diesel Particulate Filter): Manages DPF regeneration and component teach-in.
- TPMS RESET (Tire Pressure Monitoring System): Performs learning, matching, and resetting functions for tire pressure sensors.
- Other functions include: A/C Relearn, Throttle Adaptation, EPS Adaptation, Water Pump Actuation, Power Balance, CPS Reset, Gearbox Adaptation, Write VIN, Tire Size Reset, Suspension Adaptation, ABS/ESP Adaptation, Clutch Adaptation, Control Unit Reset, ADAS, Speed Limit, HV Battery, Rain/Light Sensor, Seat Calibration, Transport Mode, Stop/Start Reset, NOx Reset, RGR Relearn, Turbo Relearn, FRM Reset, Headlight, Language Change, Windows Initialization, ECU Configurations, EEPROM, AFR Adaptation.
4.4 Key Programming
The X100 MAX app provides comprehensive key programming software to access vehicle immobilizer systems.

Figure 5: Key Programming Interface with KC501
4.4.1 KC501 Connection
- Turn on the device.
- Power up the VCI box with vehicle connection or 12V power input. Vehicle connection is necessary when programming keys.
- Connect the device and the KC501 using the USB cable.
4.4.2 Common Immobilizer Functions
- Read PIN Code/PIN Code Calculation: Used to retrieve PIN codes.
- Check Number of Keys: Displays the number of keys registered to the vehicle.
- Add Keys: Adds new keys to the vehicle's immobilizer system.
- All Key Lost: Clears all saved key passwords and programs new keys when all original keys are lost.
4.4.3 Advanced IMMO Expansion with Adapters

Figure 6: X100 MAX Compatible Accessories
- KC501: For VW 4th & 5th IMMO, Mercedes-Benz Infrared key Increase, Read & Write Chip.
- KC100: For VW/Audi/Skoda/Seat/Bentley, 4th & 5th, MQB IMMO.
- M822: For Mercedes-Benz All Key Lost, Toyota 8A All Key Lost.
- KS01: For Toyota Smart Key All Key Lost, 94 Chip Smart Key.
- SK1: For 2013-2022 Toyota/Lexus Models With 8A/4A Chip Smart Keys, Add Key/All Keys Lost, Emergency Start, Frequency & Key Type Reading.
4.5 Advanced Diagnostic Features
- AI-Assisted Repair Technology: Streamlines diagnostic efficiency by providing deep fault analysis, structured repair logic, and predictive repair paths after reading DTCs. (Note: AI repair steps are for reference only; always consult vehicle repair manuals and mechanics for final recommendations.)
- ECU Online & Offline Coding & Hidden Feature Activation: Performs online coding, component matching, adaptive data reset, and flashes hidden functions for VW/AUDI/SKODA. Activates higher-level car functions and disables annoying features for BMW/VW/AUDI/SKODA/TOYOTA/LEXUS/SCION/MAZDA/FORD/LINCOLN.
- Intelligent Module Topology: Scans all available car modules and displays their diagnostic status with color-coded visual mapping of the communication network.
- Full Bi-Directional Control: Commands car ECUs to perform various active tests (e.g., Injector Tests, Compression Test, A/C Clutch On/Off, ABS Motor Pump, Window/Door operation).
- FCA AutoAuth & Dual Protocol Support (CAN FD/DoIP): Supports FCA AutoAuth for Dodge/Jeep/Chrysler/Fiat and is compatible with newer vehicles using CAN FD (GM 2020+) and DoIP protocols (BMW E/F/G Chassis, Jaguar, Land Rover).
- Pre/Post-Scan Verification & Professional Reporting V2.0: Performs comprehensive pre-scans to identify issues before repairs and post-scans to verify resolution. Generates detailed professional reports.
4.6 Vehicle Coverage & Language Support

Figure 7: X100 MAX Worldwide Vehicle Coverage
The X100 MAX supports over 150 brands and 10,000+ vehicles globally, including local dealer models from Brazil, Russia, Europe, Malaysia, and the US. Functions vary by vehicle; please contact XTOOL support with your VIN to check compatibility before purchasing.

Figure 8: X100 MAX Language Support
The device supports 22+ languages including Arabic, French, Danish, German, Greek, English, Spanish, Finnish, Hungarian, Italian, Japanese, Korean, Dutch, Norwegian, Polish, Portuguese, Russian, Swedish, Thai, Turkish, Vietnamese, Traditional Chinese.
How to change the language:
- Swipe down from the top-right corner of the tablet, press and hold the Wi-Fi icon, then go to Wi-Fi settings and connect to a network.
- Open the Diagnostic App, navigate to Settings → About → App, and update to V5.7.58 or higher.
- Switch the language in the "Other Language" section.
Note: After changing the language, please return to the "Update" page to re-download the vehicle software package.
5. Maintenance
5.1 Software Update
After activating the device, please update the software modules identified in the "Updates" screen. The device will identify all currently available software packages, and you can download them as needed directly via the Internet. To access the update application, open the Diagnostic application and click Updates.
Caution: After contacting XTOOL Support to change the language configuration, you need to download all the software packages on the device again.
5.2 Factory Reset
To restore factory settings in the Android OS system, the device will automatically erase any custom settings and data, restart, and then enter the factory reset mode. A factory reset is triggered by clicking the Settings mode from the main home page, and then clicking on "Backup & reset". Follow onscreen prompts to initiate the factory reset process.
6. Troubleshooting
6.1 DTC Status Descriptions
| DTC Status | Descriptions | Suggestions |
|---|---|---|
| Current/Present | Current DTCs are trouble codes that are stored in the ECU when both continuous and non-continuous (2 trip) monitors fail. Current DTCs command the MIL on the instant they are stored in the ECU. | Current DTCs can be cleared using the Clear DTCs function of the Scantool, or when the ECU monitor (2 trip monitor) has run and completed 40 consecutive trips without a fault. |
| History/Stored | History DTCs are trouble codes stored in the ECU when continuous and non-continuous monitors (2nd trip) fail. History DTCs set in conjunction with Current DTCs and are not cleared by the ECU monitor. History DTCs can only be cleared using the Clear DTC function of the Scantool. | History DTCs set in conjunction with Current DTCs and are not cleared by the ECU monitor. History DTCs can only be cleared using the Clear DTC function of the Scantool. |
| Pending | Pending codes are codes that prep themselves when they determine a fault that engine cycle. They are basically a preliminary investigation for your engine. To simplify, a random malfunction can occur during the current drive cycle but only happen for a split second. This will cause the malfunction to throw a "pending code". | Typically pending codes are not severe but you shouldn't ignore them either, it can be cleared using the Clear DTCs function of the Scantool. |
| Permanent | Permanent DTCs are trouble codes that are stored in the ECU when continuous and non-continuous monitors fail. Permanent DTCs are set in conjunction with Current and History DTCs. | Permanent DTCs cannot be cleared using the Clear DTCs function on the Scantool. Instead, Permanent DTCs are cleared when the ECU monitor completes and passes three consecutive trips. |
| Active/static | Active/Static means that the fault is happening at the moment and can/should be take care of. | The fault cannot be cleared directly by using the Clear DTCs function of the diagnostic tool and the internal fault of the car must be eliminated manually. |
| Passive/sporadic | It is a fault that has occurred in the past and can be cleared by Scantool, and user should to check if the DTC will appear again. | / |
7. Specifications

Figure 9: X100 MAX Hardware Details
| Attribute | Value |
|---|---|
| Model Name | XTOOL X100MAX |
| Operating System | Android 10.0 |
| Display Size | 9.7 inches |
| Display Resolution | 1024*768 |
| Processor | 4-Core, 1.8GHz |
| Memory | 4GB RAM + 128GB Storage |
| Battery | 6400mAh, 7.3V |
| Camera | 8MP Rear |
| Wireless Function | Wifi |
| Communication Interface | OBD-II, Bluetooth, Wi-fi, USB |
| Charger | Type-C Fast Charging |
| Software Version | 2026 |
| Hardware Version | 2026 |
| External Testing Certification | CE |
| Material | Plastic |
| Item Type | Auto Key Programmer |
| Item Weight | 8kg |
| Item Height | 16cm |
| Item Width | 37cm |
| Item Length | 53cm |
| Is Batteries Included | Yes |
8. Warranty & Support
8.1 Aftersales Services
For technical assistance, please contact XTOOL support:
- E-Mail: supporting@xtooltech.com
- Tel: +86 755 21670995 or +86 755 86267858 (China)
- Official Website: www.xtooltech.com
8.2 Remote Assistance
The device supports remote assistance via TeamViewer QuickSupport. This allows XTOOL technical support to remotely control your tablet to help resolve issues.
- Turn on the power of the tablet.
- Click Remote in the Diagnostic application. The TeamViewer screen is displayed, and the device ID will be generated.
- Provide your ID to the partner or XTOOL technician, and then wait for them to send you a remote-control request.
- A pop-up window will be displayed, asking you to permit the remote-control program to control your device. Click Allow to accept, or click Reject to reject.
8.3 Warranty and Updates
- 2-Year Free Update: The device comes with 2 years of free software updates.
- 2-Year Warranty: All products have passed strict quality tests and come with a 2-year warranty.
- Lifetime Technical Support: XTOOL provides lifetime technical support.
- 24-hour Online Service: Professional technical support is available 24/7.
9. User Tips
- Vehicle Compatibility: Not all functions are available for all car models and years. It is recommended to contact XTOOL support with your specific car model and VIN to check compatibility before attempting advanced procedures.
- Language Change: After changing the device language, remember to return to the "Update" page to re-download the vehicle software packages for the new language.
- TPMS Relearn Timing: When performing TPMS static relearn, the first sensor must be learned within 2 minutes, otherwise, repeat the procedure from step 4.
- AI Assistant Guidance: The repair steps provided by the AI Assistant are for reference only. Always cross-reference with the vehicle's official repair manual and consult a professional mechanic for final recommendations.
- 24-Volt Vehicles: The device is specified to work with a voltage range of +9V to +36V DC, making it compatible with 24-volt vehicles.