UKGF TB-350

Contents

UKGF TB-350 3.5-inch Coaxial Car Speakers User Manual

Model: TB-350

1. Introduction

Thank you for choosing the UKGF TB-350 3.5-inch Coaxial Car Speakers. This manual provides essential information for the safe and effective use of your new car audio speakers. Please read all instructions carefully before installation and operation to ensure optimal performance and prevent damage.

Video: Overview of the TB-350 coaxial car speakers and their packaging.

2. Safety & Warnings

WARNING:

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Professional installation is required. Securely fasten the speakers to designated vehicle mounting points (such as door panels or trunks) to prevent slipping, loosening, or damage from bumps and sudden braking, avoiding noise generation.
  • During installation, avoid key components such as vehicle airbags, steering systems, and fuel lines to avoid obstructing the path of airbag deployment and affecting vehicle safety performance.
  • The speaker wiring should be matched with the power of the car amplifier and the host to avoid burning the speaker due to high power, or affecting the sound effect due to low power, and causing component overheating.
  • Connect the wires strictly according to the markings (positive "+", negative "-"). Reversing the positive and negative poles can cause distortion of sound effects, abnormal diaphragm vibration, and long-term use may damage the speaker.
  • Ensure that the terminals are firmly connected during wiring, wrap the interface with insulating tape to avoid virtual connections and short circuits. The wiring harness should be organized in a standardized manner and kept away from high-temperature components of the vehicle (such as exhaust pipes) to prevent aging and damage to the wiring harness.
  • When the vehicle is parked for a long time, turn off the power of the car audio system to avoid the speaker being in standby mode for a long time. At the same time, take protective measures to prevent dust and debris from entering.

3. Specifications

Attribute Value
Model NumberTB-350
Brand NameUKGF
Item TypeSpeakers
Speakers TypesCoaxial speakers
Item Size3.5 Inch (8.6 CM Outside Diameter)
Out Power (Peak)MAX 80W
Rated Power (RMS)30W
Impedance4 Ω
Audio Sensitivity86dB/M/W
Signal To Noise Ratio86
Frequency Range (Hz)85HZ-4KHZ
Voltage12 V
MaterialMagnet
Item Weight0.61kg
Color NameBlack
CertificationCE
OriginMainland China
TB-350 Speaker Specifications

Image: Key specifications for the TB-350 speaker, including model, woofer size, max/RMS power, impedance, frequency response, dimension, and sensitivity.

TB-350 Speaker Dimensions

Image: Dimensional diagram of the TB-350 speaker, showing measurements in millimeters.

4. Package Contents

The package includes:

  • 1 Pair (2 units) of 3.5-inch Coaxial Car Speakers (Model TB-350)
  • Installation screws
  • Wiring terminals
  • Waterproof rings (if necessary for your installation)
TB-350 Speakers and Packaging

Image: The pair of TB-350 coaxial car speakers and their retail packaging.

TB-350 Speakers in Box

Image: The TB-350 speakers shown within their product box, highlighting the product and packaging details.

5. Setup & Installation

Before First Use:

  1. Accessory Inspection: Confirm that the speaker host, installation screws, wiring terminals, waterproof rings (if necessary) and other accessories are complete and undamaged.
  2. Installation Position: Select dedicated installation positions such as vehicle door panels and trunk to ensure space adaptation, ventilation and dryness, and avoid key components such as airbags and fuel lines.
  3. Tool Preparation: Gather screwdrivers, wire strippers, cable ties, electrical tape, and other necessary tools.

Installation Instructions:

  1. Disconnect Power Supply: Turn off the power supply of the onboard host and amplifier. Disconnect the negative terminal of the vehicle battery to avoid short circuits caused by live wiring.
  2. Fixed Speaker: Place the speaker smoothly into the installation position, firmly fix it with matching screws, and install a waterproof ring (if necessary) to ensure that it does not loosen or shake when the vehicle is bumpy.
  3. Wiring Operation: Connect the speaker to the host/amplifier according to the positive "+" and negative "-" markings of the speaker, ensuring that the positive and negative poles are consistent and the terminals are firm. Wrap the interface with insulating tape, organize the wiring harness in a standardized manner, and keep it away from high-temperature components.
TB-350 Speaker Internal Components Diagram

Image: Diagram illustrating the internal components of the TB-350 speaker, including thickened T iron, magnet, hat pressing, toilet rack, DuPont shockwave, voice coil, and drum paper.

TB-350 Speaker Construction Details

Image: Detailed view of the TB-350 speaker's construction, pointing out the high elasticity blend, high gloss basin made of refined iron, and Y35 Military Strong Magnetic components.

6. Operation

  1. Recovery and Debugging: After checking the wiring is correct, connect the negative terminal of the battery, turn on the host and amplifier, adjust the volume and sound effects, and confirm that the speaker is working properly and without noise.
  2. Power On and Off: Synchronize power on and off with the onboard host and amplifier, without the need for separate operation. It is recommended to turn off the host before turning off the engine to avoid battery depletion.
  3. Sound Effect Adjustment: Adjust the volume, high and low frequencies through the car host or amplifier to avoid prolonged high volume and high power output, prevent speaker overload damage, and not affect driving safety.

7. Maintenance

Daily Use:

  • Avoid touching the speaker diaphragm with sharp objects.
  • Prohibit foreign objects from entering the cavity.
  • Prevent sound quality distortion or component damage.

After Use:

  • Turn off the device and store it in a dry place. Keep away from children.
  • Regularly check whether the wiring terminals are secure, whether the wiring harness is damaged, whether there is no abnormal noise from the speaker, and whether the diaphragm is damaged. Any abnormalities should be dealt with in a timely manner.

8. Troubleshooting

If you experience noise or distortion from the speakers, consider the following:

  • Power Mismatch: The actual power of the speaker may not be sufficient for the volume level, causing distortion when played very loud. Ensure your amplifier's output matches the speaker's rated power.
  • Improper Connection: Check all wiring connections to ensure they are secure and correctly polarized (positive to positive, negative to negative). Incorrect wiring can lead to sound distortion and diaphragm vibration.
  • Insufficient Amplifier Power: If no power amplifier is installed, or if the host unit's power output is low, the speakers may sound loud but produce poor quality audio. An appropriate power amplifier is recommended for optimal sound.

9. User Tips

No specific user tips are available from provided user feedback or Q&A content at this time.

10. Compliance Information

This product complies with relevant electrical equipment standards as indicated by the CE certification.

Certificate of Compliance:

  • Certificate Number: KOT-2021063828C
  • Test Standard: EN 55032:2015+A11:2020, EN 55035:2017+A11:2020, EN 61000-3-2:2019, EN 61000-3-3:2013+A1:2019, EN 61000-4-2:2009, EN 61000-4-3:2020, EN 61000-4-4:2012, EN 61000-4-5:2014+A1:2017, EN 61000-4-6:2014, EN 61000-4-8:2010, EN 61000-4-11:2020

A detailed user manual (PDF) is available for download at the seller's site for further information regarding item guides and documents.

11. Manufacturer & EU Representative Information

Manufacturer:

  • Company Name: Guangzhou Kuer Automotive Supplies Co., Ltd.
  • Full Address: Yiyou (International) Auto Parts Commodities Trading Center, No. 155 HengFu Road
  • Email: 1033789983@qq.com

EU Authorized Representative:

  • AR Company Name: E-CrossStu GmbH
  • Full Address: Felix-Dahn-Str 4
  • Email: E-CrossStu@web.de

Importer:

  • Importer Name: Guangzhou Kuer Automotive Supplies Co., Ltd.
  • Full Address: Yiyou (International) Auto Parts Commodities Trading Center, No. 155 HengFu Road

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.