BAOFENG UV6

Contents

BAOFENG UV6 Walkie Talkie User Manual

Model: UV6

BAOFENG UV6 Walkie Talkie with 8W power and 2000mAh battery
Figure 1: BAOFENG UV6 Walkie Talkie

1. Introduction

Thank you for purchasing the BAOFENG UV6 Walkie Talkie. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communication with peak efficiency. To ensure optimal performance and safe operation, please read this manual carefully before use.

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your UV6 Walkie Talkie.

2. Regulatory Information and Safety Warnings

2.1. EU Regulatory Conformance

This product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC (2014/53/EU), 2006/66/EC, 2011/65/EU, and 2012/19/EU. This information is applicable to EU countries only.

2.2. FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

2.3. FCC RF Exposure

WARNING: It is up to the user to properly operate this radio transmitter to ensure safe operation. Please adhere to the following:

  • Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result.
  • Contact your local dealer for a replacement antenna.

Hand-Held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.

Body-Worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. Any additional or optional accessories not approved by the manufacturer should be avoided as they might not comply with FCC RF exposure guidelines.

2.4. Precautions for Portable Terminals

Operating Prohibitions

To protect against property loss, bodily injury, or death, observe the following safety instructions:

  1. Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials. Only approved Ex-protection models are allowed in such locations, and assembly/disassembly is strictly prohibited.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where wireless communication equipment is completely prohibited.

Important Tips

To make better use of the product, observe the following instructions:

  • Do not use any unauthorized or damaged accessory.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Do not keep the product receiving at high volume for a long time.
  • For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Continuous transmission for a long time may lead to heat accumulation. Keep it in a proper location for cooling.
  • Handle the product with care.
  • Do not disassemble, modify, or repair the product and its accessories without authorization.

2.5. Precautions for Batteries

Charging Prohibitions

  • Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  • Do not charge a wet battery. Dry it with a soft, clean cloth prior to charging.
  • Do not charge a battery suffering from deformation, leakage, or overheating.
  • Do not charge your battery with an unauthorized charger.
  • Do not charge your battery in a location where strong radiation is present.
  • Overcharging is prohibited as it may shorten battery life.
  • Do not dispose of the battery in fire.
  • Do not expose the battery to direct sunlight for a long time or place it close to other heating sources.
  • Do not squeeze, penetrate, or remove the battery housing.

Transportation Instructions

  • Damaged batteries must not be transported.
  • To avoid short circuits, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  • The radio must be switched off and secured against switch-on if the battery is attached.
  • The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for local regulations and further information.

3. Setup

3.1. Items in the Package

Ensure all items are present in your package:

Components included in the BAOFENG UV6 package
Figure 2: Package Contents
Item Quantity (PCS) Item Quantity (PCS)
Radio Body 1 Power Adapter 1
Li-ion Battery (7.4V 1800mAh) 1 Lanyard 1
Antenna 1 User's Manual 1
Belt Clip 1 PPT Earpiece 1
Battery Charger (Desktop Charger) 1

*Charger and power adapter may vary based on dealer configuration. Charging instructions in this manual may not be appropriate if Type-C charging method is used.

3.2. Product Overview

Familiarize yourself with the main components of your BAOFENG UV6 Walkie Talkie:

Diagram of BAOFENG UV6 Walkie Talkie controls
Figure 3: BAOFENG UV6 Walkie Talkie Components
  1. Antenna
  2. SK1 - Customized Function Keys/Monitor button
  3. PTT-A Button
  4. OK/Menu button
  5. V/M-VFO/MR button
  6. PTT-B Button
  7. Numeric Keypad
  8. Flashlight
  9. Volume/Power Knob
  10. Screen
  11. Accessory Port
  12. Cancel/Back button
  13. Up button / Down button
  14. A/B button
  15. Microphone
  16. LED Indicator
  17. Battery Latch
  18. Type-C Charging indicator light
  19. Type-C Charging Port
  20. Search/Flashlight button

3.3. Attaching the Antenna

Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.

CAUTION: Do not hold the radio antenna in your hand during operation, as this will reduce performance and antenna life. Do not shake the radio by the antenna.

3.4. Attaching the Belt Clip

  1. Use a Phillips screwdriver to turn the screw on the back of the radio counter-clockwise and remove it.
  2. Align the screw holes on the belt clip with the screw holes on the back of the radio.
  3. Put the screws back in place and use a Phillips screwdriver to turn the screws clockwise until hand-tight.

3.5. Battery Installation and Charging

When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging. The battery's LEDs provide an indication of the current state of charge:

BAOFENG 7.4V 2000mAh Lithium Polymer battery and battery compartment
Figure 4: Battery and Charging
Indicator light Charging status
Red light is always on Charging
Green light is always on Charging complete

4. Operating Instructions

4.1. Basic Operations

Turning Your Radio On and Off

  • To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
  • To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.

Setting the Volume

  • Increase volume by turning the [Volume/Power] rotary knob clockwise.
  • Decrease volume by turning the [Volume/Power] rotary knob counterclockwise.

CAUTION: Do not hold the product close to your ear if the volume is set to an uncomfortable level, as it could cause hearing damage.

Locking or Unlocking Keypad

To avoid accidentally changing radio settings:

  1. Press and hold the [*] key to lock the keypad until the screen displays the "lock" icon.
  2. In lock mode, you can turn the intercom on and off, adjust volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
  3. To unlock, press and hold the [*] key again until the "lock" icon is no longer displayed.

Keypad Entry

You can enter radio aliases, channel aliases, numbers, etc., using the numeric keypad.

  • To switch between input methods, press the [#1] key.
  • Press '1' to enter a special character (except in numeric input mode).
  • Press '0' to enter a space (except in numeric input mode).

Select a Channel

The channel is the medium through which the signal is transmitted.

  • Press the [V/M] button to toggle between VFO (Frequency) and Channel mode.
  • In Channel mode, use the ▲/▼ buttons or the rotary encoder to select the desired channel.
  • Alternatively, enter the channel number directly using the keypad (e.g., '064' for channel 64).

Channel Memory

In Frequency and Standby mode, you can store frequencies and parameters.

  1. Press [MENU] [3] [MENU] [1] [5]. The screen will display "MEMCH".
  2. Press [MENU] to enter the function.
  3. Use the ▲/▼ buttons to select the desired channel slot.
  4. Press [MENU] to store the frequency. A sound tone will confirm success.
  5. Press [EXIT] to return to standby mode.

NOTE: If you want to set CTCSS tones, DCS codes, or frequency offset, do so before storing the channel. Stored channels are displayed as CH-.

Delete a Channel (DEL-CH)

In VFO mode and standby mode:

  1. Press [MENU] [3] [MENU] [1] [6]. The screen will display "DELCH".
  2. Press [MENU] to enter the function.
  3. Use the ▲/▼ buttons or rotate the encoder to select the channel you want to delete.
  4. Press [MENU] to confirm.
  5. Press [EXIT] to return to standby mode.

NOTE: Channel 1 cannot be deleted.

Main Band/Sub Band Switch

In standby mode, press the [A/B] key to toggle between the A and B bands. The highlighted band is the main band; the darker displayed band is the sub-band.

VFO/Channel Switch

Press the [V/M] button to switch between VFO (Frequency) and Channel display. VFO mode displays the 'VFO' icon, while MR mode displays the channel serial number.

Setting the VFO Frequency

Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.

  • Operation 1: Input the VFO frequency directly with the keypad.
  • Operation 2: Press the ▲/▼ button or rotary encoder to adjust the VFO frequency in the set frequency step.

Call Service (Transmitting and Receiving)

All radios in the group must be set to the same channel and sub-code to communicate. For optimal reception volume, keep the microphone 2.5 cm to 5 cm from your mouth when transmitting.

  • Initiate a call: Select a channel, then press and hold the [PTT-A] key (for segment A) or [PTT-B] key (for segment B). The red indicator light will be on. Speak into the microphone with a normal voice tone.
  • Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light will be on.

Note: In standby, press and hold the '8' key to toggle the transmission power.

Emergency Alarm

The emergency alarm function allows the terminal to initiate an alarm to seek help. In standby mode, press the preset [SOS] key to enable or disable the emergency alarm function.

Flashlight

In standby mode, press the preset 'flashlight' key to turn the flashlight on or off.

FM Radio Function

Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1.

Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen displays the tuning frequency. Operations:

  • Press ▲/▼ key to search for radio channels at the preset step frequency.
  • Press the [#1] key to automatically search for radio channels; the screen displays 'SEEK...'.
  • Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
  • Press SK1 key [FM Radio] to exit radio mode.

Monitor

Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals on the current channel. This also allows you to adjust the volume when not receiving. Release the [Monitor] key to exit monitor mode.

Press the pre-programmed [SEARCH] key or press and hold the 'search' key to enter frequency search state, displaying "SEARCH...". Press [#1] key to switch the searching band (VHF/UHF). The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.

Reverse Frequency Function

Short press the [*] key in relay mode to invert the receive and transmit frequencies. The screen shows an 'R' icon. This function is useful in repeater channels when there is a frequency difference between receive and transmit frequencies.

Talk Around Function

In repeater mode, press the [*] key to switch between Talkaround Mode and Repeater Mode. The screen displays 'T' and 'R' icons. In Talkaround mode, the receive frequency equals the transmit frequency.

Repeater Activation Tone

Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit 1750Hz audio to activate a repeater in hibernation.

Voice-activated transmit (VOX)

Enable VOX function to transmit automatically through voice without pressing the PTT key. Transmission stops automatically after speech ceases.

  1. From standby, press [MENU][2][MENU][4] to enter Vox Switch.
  2. Press [MENU][2][MENU][5] to enter Vox Level. Use ▲/▼ to select VOX level (1-9). A smaller value indicates higher sensitivity. The 'V' icon appears on the screen when VOX is active. Default is off.
  3. Press [MENU] to save the setting. Select OFF to turn off VOX.

Dual Watch

In Dual Watch mode, the radio can receive frequencies set for channel A or B.

  1. Press [MENU] [2] to enter Radio Set.
  2. Press [MENU] + ▲/▼ to select "15 Dual Watch".
  3. Press [MENU] to enter Dual Watch Setting. Use ▲/▼ to select "On".
  4. Press [MENU] to save. The 'D' icon will appear. To turn off, repeat steps and select "Off".

Stopwatch Function

Press and hold the [MENU] key to enable the stopwatch function.

  • Press [MENU] to start.
  • Press [MENU] again to stop.
  • Press [EXIT] to exit.

Weather Radio/Scan Weather Channel (NOAA)

Your radio has a NOAA Weather Radio function to receive weather reports and scan all 10 NOAA Weather Radio channels.

  1. To turn NOAA Weather Scan on, press and hold the [0] key for 3 seconds. A weather icon appears, and the radio enters Weather band mode.
  2. Press and hold the [#1] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Holding [#1] again stops the scan.
  3. After stopping the scan, you can manually select weather channels using the ▲/▼ keys.
  4. To exit Weather Radio broadcast mode, press the 'weather' key or [PTT] key.

NOTE: Weather Channels Wx 1 Thru 10 are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

4.2. Using Menu Functions

Basic Use with Arrow Keys

  1. Press [MENU] to enter the menu.
  2. Use ▲/▼ buttons or the encoder to navigate.
  3. Press [MENU] again to select a menu item.
  4. Use ▲/▼ buttons or the encoder to select the desired parameter.
  5. To confirm, press [MENU] (saves setting and returns to main menu). To cancel, press [EXIT] (resets and exits menu).
  6. To exit the menu at any time, press [EXIT].

Using Menu with Shortcuts

  1. Press [MENU] to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press [MENU].
  4. For parameters, use arrow buttons or numerical keypad for short-cut code.
  5. Confirm with [MENU] or cancel with [EXIT].
  6. Exit menu with [EXIT].

4.3. Wireless Program Radio

You can program the radio wirelessly using a dedicated APP. Before programming, install the APP on your Android or iOS device.

Download Radio APP:

After opening the APP, allow Bluetooth and location functions. Select the "5Rmini Series" walkie-talkie model, connect the radio, and click "Walkie-talkie". A connection success prompt will appear, and you can return to the home page.

  • Read radio data: After reading the frequency, click 'program' to enter program details. You can program channel information, frequency mode, and optional functions.
  • Save Profile: Save the programmed profile as a new profile.
  • Write data to radio: From the home page, select 'program', click 'Write' to enter write frequency. The radio will restart automatically after writing.

To enable Wireless CPS on the radio:

  1. Press [MENU] + [4] to enter Wireless CPS.
  2. Press [MENU] + ▲/▼ to select "On". The 'wireless' icon will be displayed on the first line of the screen.

4.4. Shortcut Menu Operations

The following table details the various menu options and their functions:

Menu No. Name Setting Description
Radio Setting
1 Freq Ranger NNNNnnn Input VFO range lower and upper frequency
2 Scan Mode Time Scanning resumes after a fixed time.
Carrier Scanning resumes after the signal disappears.
Search Scanning will not resume.
3 Scan Memory ALL RX_TX are saved (default is all, encoding and decoding are the same)
DECODER Save only in Transmitter CTCSS/DCS
ENCODER Save only in Receiver CTCSS/DCS
1 Step 2.5-100K Selects frequency change amount in VFO/Frequency mode.
2 Squelch OFF, LEVEL1-LEVEL5 Silences receiver when no signal. Setting to 0 opens squelch entirely.
3 Power Save OFF Turns off radio sleep (high battery consumption).
ON Turns on radio sleep (more power efficient, but may miss initial syllables).
4 VOX Switch OFF Turns off radio VOX.
ON Turns on radio VOX.
5 VOX Level LEVEL1-LEVEL9 Adjusts VOX sensitivity for smooth transmission without PTT.
6 VOX Delay 0.5......2.0s Extends transmission time to avoid stopping too early (0.1s steps).
7 TOT OFF Allows continuous launch (no time limit).
15;30;45...180 Maximum allowed transmission time while holding PTT key.
8 TOA OFF Disable TOA function.
1......10 Activate TOA function (0-10 seconds, 1-second steps).
9 Voice OFF Disable voice prompts.
ON Activate voice prompts.
10 Language Chinese Display menus and voice prompts in Chinese.
English Display menus and voice prompts in English.
11 ROGER OFF Disable ROGER function (no audio on PTT release).
BEEP Activates ROGER function (end-of-transmission tone).
TONE 1200 Activates ROGER function (DMC1200 transmission end tone).
12 Beep OFF Disable key confirmation tone.
ON Activation key to confirm tone (audible confirmation of key press).
13 BackLight ALWAYS ON Backlight is always on.
5......20 Set backlight off time in no-operation delay (5-20 seconds, step 5).
14 Power on PICTURE Show preset picture when radio is on.
VOLTAGE Display battery voltage when radio is on.
15 Dual Watch OFF Disable dual table, dual receive.
ON Monitor [A] and [B] at the same time. Display with most recent activity becomes selected.
16 AutoLock OFF Disable automatic keypad lock. Allow manual lock (press and hold * key).
ON Keypad locks if not used in 8 seconds. Pressing * for 2 seconds unlocks.
17 Alarm Mode On Site Sounds alarm through radio speaker only.
Send Sound Transmits a cycling tone over-the-air.
Send Code Transmits '119' (911 in reverse) followed by ANI code over-the-air.
18 Alarm Tone OFF Radio speaker blocks the alarm sound.
ON Radio speaker sounds an alarm.
19 ANI-Edit 100 View and change ANI ID.
20 Display ANI OFF Disable ANI code display function.
ON Enable ANI code display.
21 DTMF-ST OFF No DTMF Side Tones are heard.
DT-ST Side Tones heard only from manually keyed DTMF codes.
ANI-ST Side Tones heard only from automatically keyed DTMF codes.
DT+ANI All DTMF Side Tones are heard.
22 PTT-ID OFF No ID is sent.
BOT Selected S-CODE is sent at the beginning.
EOT Selected S-CODE is sent at the ending.
BOTH Selected S-CODE is sent at the beginning and ending.
23 PTT-DLY 100-3000ms Signal code sending delay (milliseconds).
24 ALERT 1000Hz PTT + SK1 = Transmits 1000Hz Tone Burst.
1450Hz PTT + SK1 = Transmits 1450Hz Tone Burst.
1750Hz PTT + SK1 = Transmits 1750Hz Tone Burst.
2100Hz PTT + SK1 = Transmits 2100Hz Tone Burst.
25 TAIL OFF Disable Squelch Tail Elimination.
ON Enable Squelch tail elimination to prevent squelch tails.
26 Press SK1 FM Radio FM Radio on/off.
SCAN SCA on/off.
SEARCH Search on/off.
VOX VOX on/off.
LAMP Flashlight on/off.
SOS SOS on/off.
27 Reset VFO MODE Reset radio's VFO menu to factory defaults (no bank/scan settings).
RESET ALL Resets radio to factory defaults, with some exceptions.
Program Channel
1 CH.NAME Channel 1 View/rename current channel. Use #z key for input.
2 RX Frequency View current channel Receiver frequency.
3 TX Frequency View current channel Transmitter frequency.
4 Trans Power High Selects HIGH transmitter power in VFO/Frequency mode.
Low Selects LOW transmitter power in VFO/Frequency mode.
5 Bandwidth Wide Wideband (25 kHz bandwidth).
Narrow Narrowband (12.5 kHz bandwidth).
6 RX CTCSS OFF;67-254.1 Mutes speaker in absence of specific sub-audible signal.
7 RX DCS OFF;023N-7541 Mutes speaker in absence of specific low-level digital signal.
8 TX CTCSS OFF;67-254 Transmits specific sub-audible signal to unlock distant receiver.
9 TX DCS OFF;023N-7541 Transmits specific low-level digital signal to unlock distant receiver.
10 Encryption OFF Disable encrypted mode (conversations not private).
ON Activates encryption mode (privacy). Other radios must also have encryption active and same DCS code.
11 Signaling 1-20 Selects one of 20 DTMF codes (up to 3 digits).
12 CH-MDF NAME MR/Channel mode displayed in NAME format.
FREQ MR/Channel mode displayed in frequency format.
CH MR/Channel mode displayed in CH format.
13 SP-Mute QT Monitor activated only when correct CTCSS/DCS is received.
QT+DTMF Monitor activated when correct CTCSS/DCS and DTMF code are received.
14 SCAN ADD OFF Forbid current channel to join scan group.
ON Add current channel to scan group.
15 Busy Lockout OFF PTT button on channel is always allowed.
ON Disables PTT button on busy channel; transceiver beeps and won't transmit.
*13 OffSet Specifies difference between TX and RX frequencies.
None TX = RX (simplex). Disable access to repeaters in VFO/Frequency mode.
Plus Plus frequency shift direction (TX shifted higher than RX).
*14 Direction Minus Minus frequency shift direction (TX shifted lower than RX).
16 CH_Memory CH001-CH999 Create/modify channels (1-999) for MR/Channel Mode.
17 CH_Delete CH001-CH999 Delete programmed channel information.
Wireless CPS
1 OFF Turn off Wireless CPS and disable programming.
ON Enable Wireless CPS to program radio via Wireless.
Radio Info
Radio ID\Firmware\Hardware Displays radio ID, firmware version, hardware version.

5. Maintenance

Your Two-Way Radio is an electronic product of precise design and should be treated with care. The following suggestions will help you fulfill warranty obligations and enjoy this product for many years.

  • Do not attempt to open the radio for any reason. Its precision mechanics and electronics require specialized equipment. Unauthorized opening voids the warranty.
  • Do not store the radio under direct sunlight or in hot areas. High temperatures can shorten the life of electronic devices and warp plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the radio dry. Rainwater or dampness will corrode electronic circuits.
  • If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
  • Do not transmit without an antenna.

5.1. Battery Maintenance Instructions

To help your battery work normally and prolong its life:

  • Clean accumulated dust on the charging connector regularly with a clean, dry cloth.
  • Charge the battery between 5°C and 40°C. Charging outside this range may reduce battery life or cause leakage.
  • To ensure a full charge when charging a battery attached to the product, turn the product off.
  • Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.

6. Troubleshooting

If you encounter issues with your BAOFENG UV6, try the following basic troubleshooting steps:

  • No Power: Ensure the battery is properly installed and charged. Turn the Volume/Power knob clockwise to power on.
  • Cannot Transmit/Receive: Check if the radio is on the correct channel and sub-code. Ensure the antenna is securely attached. Verify that the keypad is not locked. Check battery level.
  • Poor Audio Quality: Adjust the volume. Ensure the microphone is 2.5-5 cm from your mouth during transmission. Check for obstructions or damage to the microphone/speaker.
  • Keypad Unresponsive: The keypad might be locked. Press and hold the [*] key to unlock it.
  • Radio Overheating: Avoid continuous transmission for extended periods. Allow the radio to cool down in a well-ventilated area.
  • Charging Issues: Ensure the charger and battery are dry and free of dust. Use only authorized chargers. Check if the battery is deformed or leaking.

If problems persist, consult the full user manual PDF or contact customer support.

7. Specifications

7.1. Functional Features

  • 6-band scan receiver: FM 78-108MHz; AM 108-136MHz; VHF 136-174MHz, 220-260MHz; UHF 400-520MHz, 350-390MHz
  • Transmit frequency: VHF 144-148MHz; UHF 420-450MHz
  • 5W/2W RF output, dual PTT transmitter (Product title indicates 8W)
  • Wireless read/write frequency
  • 1.44" TFT large screen, full keyboard, full open menu operation
  • Local channel storage and deletion, 999 channel memory
  • Full keyboard manual frequency input
  • One-click frequency pairing, easy pairing and grouping
  • Relay function settings: frequency difference, frequency difference direction, relay activation audio settings
  • Alarm function (three types of alarm settings)
  • Built-in input method: supports local editing of channel name, receiving frequency, transmitting frequency
  • DTMF encoding and decoding function, 20 DTMF calls
  • Frequency hopping function
  • Side button function customization: radio, scan, sweep, voice control, flashlight, alarm
  • FM radio function (receive frequency 78~108MHz)
  • Automatic or manual keypad lock, backlight selection
  • 7.4V_2200mAh rechargeable lithium battery life
  • Support Type-C charge
  • PC Program
  • Voice Prompt
  • DTMF Side Tone
  • Chinese/English Switch
  • Battery Saving
  • VOX Function
  • Busy Channel Lock Function
  • Low Battery Warning
  • Over Voltage or Low Voltage Protection
  • 3 Scanning Ways (Time, Carrier wave, Search)
  • PTT-ID (Press PTT to transmit code, release PTT to transmit code, or both can transmit code)
  • Channel Monitor
  • TOT (Time-out Timer)
  • High & Low Power Switchover

7.2. General Specifications

Parameter Value
Unity Section
Frequency Range 136.00-174.00 MHz, 400.00-480.00MHz
Storage Channel 999 Groups
Step Frequency 2.5/5/6.25/10/12.5/20/25KHz
Rated Voltage DC 7.4V
Battery Capacity 7.4V 2200mAh (Li-ion Battery)
Battery Life About 10 Hours
Frequency Stability ±2.5ppm
Work Temperature -20℃ to +60℃
Frequency Combination PLL frequency synthesis
Antenna Impedance 50 Ω
Work Mode Same Frequency simplex Operation or Different Frequency simplex Operation
Dimensions 108mm × 52mm × 37mm (No antenna)
Weight 200g (Battery pack included)
Transmitter
Output Power 5W/1W (Also advertised as 8W)
Modulation Mode (W/N Band) FM (F3E)
Maximum Frequency Deviation (W/N Band) <5KHz(W), <2.5KHz(N)
Spurious Radiation ≤7.5 µW
Adjacent channel power ≦-65dB (W)/≦60dB (N)
Radiation <-60 dB
Audio Distortion <5 %
SNR 45dB(W), 42dB(N)
CTSCC/DCS Frequency Deviation (W/N Band) 0.7±0.1KHz (W), 0.4±0.1KHz (N)
Modulation Sensitivity 8-12mV
Transmitting Current ≤1600mA
Receiver
Sensitivity 0.25µV (12dB SINAD)
Audio Power 1 W
Inter modulation Interference Resistance ≧65dB (W), ≧55dB (N)
Adjacent channel Sensitivity (W/N Band) ≧65dB (W), ≧55dB (N)
Audio Distortion 5 %
Spurious Response ≧60dB
Receiving Current ≦380mA

NOTE: All specifications may be modified without prior notice or liability.

8. User Tips

  • Battery Life: To maximize battery life, utilize the "Power Save" function (Menu 3, ON). For critical communications, keep it OFF to avoid missing initial transmissions.
  • Clear Communication: Always ensure your microphone is 2.5-5 cm from your mouth when speaking. Use the "Squelch" setting (Menu 2) to filter out background noise; adjust it to a level that allows clear reception without excessive static.
  • Channel Management: Regularly delete unused channels (DEL-CH) to keep your radio organized. Remember that Channel 1 cannot be deleted.
  • Programming: For advanced programming, consider using the Wireless Program Radio feature with the dedicated app for easier configuration of channels and frequencies.
  • Emergency Preparedness: Familiarize yourself with the Emergency Alarm function and how to activate it quickly in case of need.

9. Warranty and Support

The accuracy and completeness of the contents of this manual are diligently sought. However, we do not bear responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without notice. No copy, modification, translation, or dissemination of this handbook may be made without prior written authorization.

For further assistance, technical support, or warranty inquiries, please contact your authorized dealer or the manufacturer's customer service department.

A user manual in PDF format is available for download at https://manuals.plus/m/a9cbd8e1c0c971b0bcf9812771fb781769f9ecd2c402e491f6be2afa391325e7.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.