Honda 17620-GE2-931

Contents

Motorcycle Fuel Tank Cap Instruction Manual

Model: 17620-GE2-931

For Honda NSR 50, NSR75, MSX 125, CBR 125R, CBF 125 150, FX650, NX650, XRV750, XL1000, CBR1000

1. Introduction

This manual provides essential information for the safe installation, operation, and maintenance of your new motorcycle fuel tank cap. Please read all instructions carefully before proceeding.

Top view of the fuel tank cap with two keys, showing 'PUSH LOCK', 'LIFT OPEN', and 'FRONT' indicators.

Figure 1: Fuel Tank Cap (Top View) with Keys

Bottom view of the fuel tank cap with two keys, showing the rubber seal and the internal locking mechanism.

Figure 2: Fuel Tank Cap (Bottom View) with Keys

2. Safety Information (Read First)

IMPORTANT: This manual contains essential safety information compliant with the EU General Product Safety Regulation (GPSR). Fuel system components involve highly flammable liquids and pressurized systems. Failure to follow these instructions correctly can lead to fire, explosion, severe burns, or death.

WARNING

Gasoline is extremely flammable and explosive under certain conditions. Work in a well-ventilated area, away from open flames, sparks, pilot lights, or any other ignition sources (including cigarettes, cell phones, and power tools that can produce sparks). Have a Class B fire extinguisher (dry chemical) readily accessible before beginning any work.

If you are not trained in fuel system service, do not attempt this installation. Have the work performed by a certified motorcycle mechanic. Pressurized fuel systems can spray fuel when disconnected, causing severe injury and fire hazard.

General Requirements & Compliance

  • Vehicle Fitment: Verify that this component is specifically designed for your motorcycle make, model, and year. Using incorrect fuel system parts can cause improper air/fuel mixture, leading to engine damage or fire.
  • Pressure Ratings: All fuel hoses and clamps must be rated for the operating pressure of your fuel system (low-pressure for carbureted systems typically 3-7 PSI; high-pressure for fuel injection typically 35-65 PSI). Never use standard rubber hose on high-pressure fuel injection systems.
  • Service Manual: Refer to the official service manual for your motorcycle for specific routing diagrams, pressure specifications, and torque values.
  • EU Regulatory Note: This product complies with applicable EU directives. Fuel system components may be subject to Type Approval (EU Regulation 168/2013) for vehicle components. At end of life, dispose of components according to local environmental regulations (see Section 7).

Critical Safety Preparations

WARNING: Relieve fuel system pressure before disconnecting any fuel line on fuel-injected models. Failure to do so can result in high-pressure fuel spray causing fire or injury.

Risk Warnings (Specific Hazards)

Fire and Explosion Risks

  • Static Electricity: Fuel flowing through hoses and filters can generate static electricity. In dry environments, ensure proper grounding of the fuel system components. Wipe up any spills immediately.
  • Hot Surfaces: Never operate the engine with fuel leaks present. Fuel contacting the exhaust system can cause instantaneous fire.
  • Electrical Arcing: All electrical connections in the fuel system must be weather-tight and corrosion-free. A loose connection can create a spark capable of igniting fuel vapors.

Pressure System Risks

  • Fuel Injection Pressure: Fuel injection systems operate at extremely high pressure (up to 5 bar/70 PSI). Never use pliers or tools to clamp fuel lines to check for leaks—this can damage the hose internally, creating a latent failure.
  • Leak Testing: After installation, the system must be pressurized and inspected for leaks before starting the engine (see Section 5).

Health Risks

  • Inhalation: Prolonged breathing of fuel vapors can cause serious health issues. Always work in well-ventilated areas.
  • Skin Contact: Repeated or prolonged skin contact with fuel can cause dermatitis and other skin conditions. Wash thoroughly with soap and water after any contact.

Mechanical Risks

  • Debris Contamination: Even microscopic debris entering a fuel injector can cause blockage, leading to engine misfire and potential catalytic converter damage. Keep all ports capped until the moment of connection.
  • Vacuum Leaks (Carburetor): An improperly seated carburetor or cracked intake boot creates a vacuum leak, causing lean air/fuel mixture. Lean mixtures cause overheating, pre-ignition, and severe engine damage.

3. Setup and Installation

Pre-Installation: Tools & Preparation

For Fuel-Injected Systems (Pressure Relief):

  1. Remove the fuel pump fuse or relay.
  2. Start the engine and allow it to run until it stalls from fuel starvation.
  3. Crank the engine for 3-5 seconds to verify pressure is relieved.
  4. Turn ignition OFF and reinstall the fuse/relay.

For All Systems:

  1. Disconnect Battery: Disconnect the negative (-) battery terminal to prevent accidental electrical sparks.
  2. Cool Engine: Ensure the engine and exhaust system are completely cool to prevent fuel ignition on hot surfaces.
  3. Work Area: Ensure adequate ventilation to prevent accumulation of fuel vapors.
  4. Protective Equipment: Wear chemical-resistant gloves and safety glasses. Fuel can irritate skin and eyes.

Installation Procedure

A. Removal of Old Components

Fuel Lines:

  1. For Quick-Connect Fittings: Release the locking mechanism according to manufacturer instructions (push-button, pull-tab, or special tool required). Be prepared for residual fuel drainage.
  2. For Clamp-Type Hoses: Loosen clamps and twist the hose to break the seal before pulling. Never use excessive force.
  3. Plug Openings: Immediately cap or plug all open fuel lines and ports to prevent debris entry and minimize fuel spillage.

Fuel Pump (In-Tank or External):

  1. Note the orientation and routing of all electrical connections and fuel lines before removal. Take photos for reference.
  2. Carefully extract the pump assembly, avoiding damage to the fuel level sender arm.
  3. Inspect and replace the fuel pump gasket/seal and filter (if applicable).

Carburetor/Fuel Injector:

  1. Remove the air cleaner assembly to access the component.
  2. Disconnect throttle cables, choke cables (for carburetor), and electrical connectors (for injectors).
  3. Cap the intake manifold openings immediately to prevent debris from entering the engine.

B. Installation of New Components

General Rules (For ALL Fuel Components):

WARNING: Use only approved fuel-resistant components. Standard rubber vacuum hose will deteriorate rapidly when exposed to modern ethanol-blended fuels, leading to leaks and fire.

Fuel Lines Installation:

  1. Cut Cleanly: Cut fuel hose squarely using a sharp knife or hose cutter. Do not use scissors or dull tools that can deform the hose.
  2. Insert Fully: Push the hose onto the barbed fitting until it seats against the hose end. For push-to-connect fittings, push until you hear an audible "click" and the locking tabs engage.
  3. Verify Connection: Gently pull on the connection to confirm it is securely locked.
  4. Clamp Properly: Position clamps 3-5 mm from the hose end. Use only fuel-injected grade clamps (constant tension or EFI-specific worm gear clamps).

Fuel Pump Installation:

  1. Clean Sealing Surfaces: Ensure the tank mounting surface is clean and free of old gasket material.
  2. New Gasket/O-Ring: Always install the new gasket or O-ring provided with the kit. Lubricate the O-ring with clean engine oil or assembly lubricant to prevent rolling during installation.
  3. Torque: Tighten mounting fasteners evenly in a cross pattern to manufacturer specification (typically 8-12 N-m for pump covers). Overtightening can distort the flange and cause leaks.
  4. Electrical Connections: Ensure connectors click securely into place. Verify wiring is routed away from sharp edges.

Carburetor/Fuel Injector Installation:

  1. New Gaskets/O-Rings: Always use new intake manifold gaskets or injector O-rings. Lubricate O-rings lightly with clean engine oil or assembly lubricant.
  2. Fuel Injector Seating: Push the injector into the fuel rail and intake manifold until fully seated. The retaining clip should lock into position with an audible click.
  3. Carburetor Installation: Ensure the carburetor seats squarely in the intake boots. Tighten clamp bolts evenly but do not overtighten—just enough to prevent air leaks and secure the carburetor.

Fuel Tank Installation (If Removed):

  1. Isolators/Pads: Apply soapy water or rubber lubricant to tank isolators to ease installation. Ensure the tank is fully seated on the isolators.
  2. Line Routing: Verify all lines (fuel supply, return, vent) are routed away from exhaust, sharp edges, and moving parts. Ensure no wires or hoses are pinched under the tank.
  3. Fasteners: Torque tank mounting bolts to specification (typically 20-25 N-m for rear tank bolts).

4. Operation

Your fuel tank cap is designed for secure and easy access to your motorcycle's fuel tank.

Top view of the fuel tank cap in a closed position, showing the keyhole.

Figure 3: Cap in Closed Position

Angled view of the fuel tank cap with a key inserted into the lock.

Figure 4: Key Inserted

Top view of the fuel tank cap in an open position, revealing the keyhole and hinge mechanism.

Figure 5: Cap in Open Position

Opening the Fuel Tank Cap:

  1. Insert the key into the keyhole on the cap.
  2. Turn the key clockwise (or counter-clockwise, depending on the lock mechanism) to unlock the cap.
  3. Locate the
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.