RACBOX E24 Mini LED Turn Signal Light

Contents

RACBOX E24 Mini LED Turn Signal Light User Manual

Universal Blinker Indicator for Motorcycles

1. Introduction

Thank you for choosing the RACBOX E24 Mini LED Turn Signal Light. This product is designed to provide clear and effective turn indication for a wide range of motorcycles, including Cafe Racers, Choppers, Bobbers, and models from manufacturers like Honda and Yamaha. Its compact design and durable aluminum construction ensure reliable performance. This manual provides essential information for the safe installation, operation, and maintenance of your new turn signal lights.

2. Safety Information

  • Always disconnect the motorcycle's battery before performing any electrical work.
  • Ensure all wiring connections are secure and properly insulated to prevent short circuits.
  • Verify that the turn signals are functioning correctly after installation before riding.
  • Consult a professional mechanic if you are unsure about any installation steps.
  • These lights are designed for 12V systems only. Do not connect to other voltage sources.

3. Package Contents

Your package should contain the following items:

  • E24 Mini LED Turn Signal Lights (quantity as ordered, typically 2 or 4 units)
  • Mounting nuts and washers
  • Pre-attached wiring (red and black)
Two sets of E24 Mini LED Turn Signal Lights packaged in clear plastic bags.
Figure 1: E24 Mini LED Turn Signal Lights as packaged.

4. Specifications

Feature Detail
Condition 100% Brand New
Voltage 12V
Material Aluminium + PC Smoke Lens
Bulb Type LED
Mounting Bolt Thread M8 (8mm)
Housing Color Black
Light Color Amber
Wiring Two Wire System
Battery Included No
High-concerned chemical None
Origin Mainland China
Item Type Turn Signal Light
Dimensions (Approx.) Length: 38mm (1.5in), Height: 26mm (1.02in), Width: 15mm (0.59in)
Technical diagram showing the dimensions of the E24 Mini LED Turn Signal Light: 38mm (1.5in) length, 26mm (1.02in) height, and 15mm (0.59in) width.
Figure 2: Approximate dimensions of the E24 Mini LED Turn Signal Light.

5. Setup and Installation

These turn signal lights are designed for universal fitment on most motorcycles with an M8 mounting point and a 12V electrical system. Follow these general steps for installation:

  1. **Preparation:** Ensure the motorcycle is turned off and the battery is disconnected. Identify the desired mounting location for the turn signals.
  2. **Mounting:** Insert the M8 threaded bolt of the turn signal into the mounting hole. Secure it with the provided washer and nut. Tighten firmly but do not overtighten.
  3. **Wiring:**
    • Connect the Red wire from the turn signal to the motorcycle's positive (+) turn signal wire.
    • Connect the Black wire from the turn signal to the motorcycle's negative (-) or ground wire.
    Close-up of the two-wire connection (red and black) with spade connectors for the E24 Mini LED Turn Signal Light.
    Figure 3: Wiring connections (Red for positive, Black for negative).
  4. **Insulation:** After making connections, ensure all exposed wires are properly insulated using electrical tape or heat shrink tubing to prevent short circuits and corrosion.
  5. **Testing:** Reconnect the motorcycle's battery. Turn on the ignition and test the turn signals to ensure they illuminate correctly and flash at the appropriate rate. If the flash rate is too fast, a load resistor or LED flasher relay may be required (not included).

Note: Due to the universal nature of this product, specific motorcycle wiring diagrams are not provided. Please refer to your motorcycle's service manual for detailed wiring information.

6. Operating Instructions

Once properly installed, the RACBOX E24 Mini LED Turn Signal Lights operate like standard motorcycle turn signals. Activate them using your motorcycle's turn signal switch to indicate turns or lane changes. The amber LED light will illuminate to provide clear visibility to other road users.

Two E24 Mini LED Turn Signal Lights illuminated with amber light, casting a patterned glow.
Figure 4: E24 Mini LED Turn Signal Lights in operation.

Video 1: Product demonstration showing the E24 Mini LED Turn Signal Light's appearance and amber illumination.

7. Maintenance

  • Cleaning: Clean the lights periodically with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the lens or housing.
  • Inspection: Regularly check the mounting bolts for tightness and the wiring for any signs of wear, fraying, or corrosion.
  • LED Lifespan: LED lights have a long lifespan and typically do not require bulb replacement. If a light fails, inspect the wiring connections first.

8. Troubleshooting

Problem Possible Cause Solution
Light does not illuminate Loose or incorrect wiring connection, blown fuse, faulty light unit. Check all wiring connections (red to positive, black to negative). Inspect motorcycle's fuse box. If connections are correct and fuse is good, the light unit may be faulty.
Light flickers or is dim Poor electrical connection, insufficient power, corrosion. Ensure connections are clean and tight. Check for corrosion on terminals. Verify 12V power supply.
Turn signals flash too fast (hyper-flashing) LED lights draw less power than incandescent bulbs, causing the flasher relay to misinterpret the load. Install an LED flasher relay or load resistors (not included) to correct the flash rate.

9. User Tips

Based on general user experiences with similar products:

  • Consider using thread locker on the mounting bolt to prevent loosening due to vibration.
  • For a cleaner installation, use waterproof heat shrink connectors for wiring.
  • If replacing incandescent bulbs with these LEDs, you might need an LED-compatible flasher relay or load resistors to maintain the correct flash speed.

Note: No specific user tips were available from the provided customer reviews or Q&A data for this product.

10. Warranty and Support

For any questions, technical assistance, or support regarding your RACBOX E24 Mini LED Turn Signal Lights, please contact the seller directly. As per the general product information, if you cannot find the manual or are unsure how to use the product, contacting the seller is recommended.

Specific warranty details are not provided in the available product information. Please inquire with the seller for warranty terms and conditions.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.