Introduction
This 3-in-1 soil moisture meter is designed to help you understand the condition of your plants' environment. It detects soil moisture, measures the pH value of the soil, and determines the light intensity, enabling you to cultivate healthier plants.
Key Features
- 3-in-1 Functionality: Measures soil humidity, pH level, and light intensity.
- Battery-Free Operation: No batteries required, simply plug and use.
- Accurate Readings: Features a double probe design for more precise measurements.
- Easy to Use: Simple, intuitive operation for quick environmental checks.


Specifications
| Feature | Detail |
|---|---|
| Model Number | TR-01 |
| Display Type | Analog (Dial) |
| Battery Required | No |
| Humidity Range | 1-10 (1-3 Dry, 4-7 Moist, 8-10 Wet) |
| pH Range | 3.5-8 (3.5-6.5 Acidic, 7-8 Alkaline) |
| Light Intensity Range | 0-2000 Lux (0-200 Low, 200-500 Low+, 500-1000 Normal, 1000-2000 High) |
| Dimensions (Length) | 265mm / 10.43 inches |
| Origin | Mainland China |


Setup
- Unpack: Carefully remove the soil meter from its packaging.
- Inspect: Ensure the probes are clean and free from any debris.
- No Battery Needed: This device operates without batteries. It is ready for use immediately after unpacking.
Operating Instructions
The meter features a "THREE-WAY" switch to select between Humidity (MOIST), pH, and Light (LIGHT) measurements.

1. Measuring Soil Moisture (MOIST)
- Set the switch on the meter to the "MOIST" position.
- Insert the probes into the soil to a depth of 2 to 3 inches (5-7.5 cm), ensuring full contact with the soil.
- Wait for a few minutes (typically 1-2 minutes) for the needle to stabilize.
- Read the humidity value on the dial.
- 1-3 (Red): Dry, requires watering.
- 4-7 (Green): Moist, ideal.
- 8-10 (Blue): Wet, reduce watering.
2. Measuring Soil pH (pH)
- Set the switch on the meter to the "pH" position.
- Insert the probes into the soil to a depth of 2 to 3 inches (5-7.5 cm).
- Wait for a few minutes (typically 1-2 minutes) for the needle to stabilize.
- Read the pH value on the dial.
- 3.5-6.5: Acidic soil.
- 7: Neutral soil.
- 7-8: Alkaline soil.
3. Measuring Light Intensity (LIGHT)
- Set the switch on the meter to the "LIGHT" position.
- Point the light sensor (located at the top of the meter) towards the light source.
- The meter will instantly display the light intensity.
- 0-200: Low light.
- 200-500: Low+ light.
- 500-1000: Normal light.
- 1000-2000: High light.

Maintenance
- Clean Probes: After each use, wipe the probes clean with a cloth to remove any soil residue.
- Storage: Do not leave the meter inserted in soil for extended periods. Store it in a dry place.
- Intended Use: This meter is designed for testing soil only. Never use it to test water or other liquids.
- Avoid Hard Soil: Do not force the probes into very hard soil, as this may damage them.
Troubleshooting
- No Reading/Erratic Reading:
- Ensure probes are clean.
- Make sure probes are fully inserted into moist soil (2-3 inches deep).
- If soil is too dry, readings may be inaccurate. Water the soil and retest after 20-30 minutes.
- Difficulty Inserting Probes:
- The soil may be too hard or compacted. Loosen the soil gently before inserting the probes.
- Do not force the probes, as this can cause damage.
User Tips
- Optimal Watering: Use the moisture readings to water plants scientifically and rationally. If the meter reads above the recommended range, it's too early to water. If it reads at or below the range, watering is needed.
- Consistent Testing: For best results, test the soil in several spots around the plant.
- Soil Preparation for pH: For accurate pH readings, ensure the soil is slightly moist. Dry soil can lead to inaccurate results.
Additional Resources
A comprehensive user manual in PDF format is available for download:
Warranty and Support
This product is covered by a standard manufacturer's warranty. For specific warranty details, technical support, or any inquiries, please contact your retailer or the point of purchase. Please retain your proof of purchase for warranty claims.