1. Introduction
This manual provides detailed instructions for the YIHUA 110W 926LED-III Soldering Iron Kit. Please read it carefully before operation and keep it for future reference.
The company reserves the right to improve and upgrade products; product specifications and design are subject to change without notice.
This soldering station is suitable for soldering and desoldering operations on SMT (Surface-Mount Technology) and through-hole components such as SOP, DIP, SOIC, and other types of components.
2. Specifications
| Feature | Specification |
|---|---|
| Model Number | 926LED-III 110W Soldering Iron Kit |
| Maximum Power | 220W |
| Rated Power | 22W |
| Soldering Iron Power | 110W |
| Input Voltage | 110V/220V-240V (Plug type varies by region) |
| Output Temperature Range | 90℃ ~ 480℃ (194℉ ~ 896℉) |
| Temperature Stability | ± 3.6°F / 2.0°C (stable) |
| Operating Ambient Temperature | 0~40°C / 32~104°F |
| Tip to Ground Resistance | <2 ohms |
| Dimensions | L185*W72*H115mm±5mm |
| Display | LED Soldering Station |
| Certification | CE |
| Is Smart Device | No |
Key Functions:
- ESD Safe
- PID Temperature Control Technology
- °C / ℉ Switch
- Sleep Function
- Temperature Calibration Function
3. Package Contents
The YIHUA 926LED-III Soldering Iron Kit is available in different packages. Please check your specific package for included items.
Package 1:
- 1 x 926LED-III 110W Soldering Iron Station
Package 2 (Full Kit):
- 1 x 926LED-III 110W Soldering Iron Station
- 1 x Solder Wire
- 5 x Soldering Iron Tips (902-I/B/K/2.4D/3C)
- 1 x Suction Pen
- 1 x Anti-static Black Tweezers
- 1 x Cleaning Ball

4. Setup Instructions
- Place the Soldering Iron: Place the soldering iron in its holder correctly. If your station includes a solder roll holder, install it by placing it on the left side of the station, aligning the holes on the bracket with the installation holes on the station. Secure both the holder and the station to ensure they are level before tightening any screws.
- Connect Power: Connect the power cord and turn on the power switch. The heating element will begin heating. The heating indicator light will illuminate constantly during heating. Once the temperature stabilizes, the indicator light will blink. The indicator light will turn off when the station is cooling. Begin work once the temperature stabilizes.
- Initial Soldering Tip Preparation (First Use): Set the temperature to 250°C (482°F). Once the iron tip is hot enough to melt solder, coat the tip with a layer of solder (including flux). Then, adjust the temperature to your required working value.


5. Operation
Temperature Control and Display
The LED display shows the current temperature. Use the menu button/temperature adjustment dial to set your desired temperature. The indicator light (round dot on the bottom right of the display window) lights up when heating, blinks when stable, and turns off when cooling.

°F/°C Temperature Unit Display
This function allows users to select their preferred temperature unit on the display:
- Press and hold the menu dial button for 2 seconds; the station will display "C".
- Turn the dial button to select either Celsius (°C) or Fahrenheit (°F) display mode.
- Press the dial button 3 consecutive times to complete and exit the setting interface.

Sleep Mode Timer Configuration
The sleep function extends the lifespan of the soldering iron and conserves energy.
- Press and hold the dial button for 2 seconds, then press the dial button 1 time. The station will display "L10" (default 10 minutes sleep mode).
- Turn the dial button to set the sleep mode timing. Set the timer value to "L00" if sleep mode is not needed. Available settings: 0, 5, 10, 30 minutes.
- Press the dial button 2 consecutive times to complete and exit the setting interface.
To wake up the soldering station from sleep mode:
- Pick up the soldering iron and gently shake it.
- Press any button on the control panel.
- Turn OFF the power then turn ON the power.
When the temperature setting is ≥ 250°C (482°F), the temperature will drop to 200°C (392°F) in sleep mode. When the temperature setting is < 250°C (482°F), the temperature will drop to 90°C (194°F) in sleep mode.

Digital Temperature Calibration
Temperature discrepancies may occur due to changes in the operating environment, or replacement of the heating element, soldering tip, or other parts. This function helps improve work efficiency and extends the lifespan of the soldering iron.
- After the temperature of the soldering iron has stabilized, press and hold the dial button for 2 seconds, then press the dial button 2 consecutive times. The station will display "CAL".
- Turn the dial button to enter the calibrated temperature, confirm your entry by pressing the dial button once.
- Press the dial button one time to complete and exit the setting interface. Repeat the above steps if temperature differentials remain.

Soldering Process

6. Maintenance & Precautions
- Oxidized Soldering Tip: If the soldering iron tip develops an oxidized layer, it may appear unable to melt solder or tin properly, even if the heating element and tip are hot. Do not blindly increase the temperature. Instead, use a metal wool ball to remove the oxidation:
- Set the temperature to 300°C (572°F).
- Once stable, gently rub the tip inside the metal wool ball.
- When partially removed, apply solder onto the tip while rubbing until it is completely coated. If severely oxidized beyond cleaning, replace it.
- Avoid Metal Files: Do NOT use metal files to remove oxidation from the soldering iron tip. If the tip deforms or rusts, replace it with a new one.
- Avoid Excessive Force: Do NOT apply excessive force on the soldering iron tip when soldering. This will not improve heat transfer and may damage the tip.
- Idle Temperature: When placing the soldering iron back in the holder to idle after high-temperature operation, adjust the temperature to 250°C (482°F) or below. Failing to do so will accelerate the aging of the heating element and shorten its lifespan.
- Post-Operation Cleaning: After every operation, clean the soldering iron tip, then tin it with a new layer of solder to prevent oxidation. When finished, turn OFF the power switch and disconnect the power cord.
7. Troubleshooting
| Display/Issue | Description | Solution |
|---|---|---|
| "S-E" | Soldering iron sensor module error. | Replace the heating element (which includes the sensor module). |
| "SLP" | The station is in sleep mode. | Wake up the station by shaking the iron, pressing any button, or cycling the power. |
| Heating element replacement | Ensure correct wiring order and colors. | When replacing the heating element, pay attention to the original connecting order and colors of the wires, which MUST NOT be connected incorrectly. |
8. Compatible Soldering Tips
The YIHUA 926LED-III Soldering Iron Kit is compatible with 900M series and 902 series tips with an outer diameter of 6.5mm.
Examples of Compatible Tips:
- 900M Series: 900M-T-0.8D, 900M-T-LB, 900M-T-K, 900M-T-1.2D, 900M-T-1.6D, 900M-T-2.4D, 900M-T-3.2D, 900M-T-0.5C, 900M-T-0.8C, 900M-T-1C, 900M-T-1.5CF, 900M-T-2C, 900M-T-3C, 900M-T-4C, 900M-T-1, 900M-T-H, 900M-T-1.8H, 900M-T-54, 900M-T-R, 900M-T-RT, 900M-T-SI, 900M-T-SB, 900M-T-B, 900M-T-1.2LD
- 902 Series: 902-B, 902-I, 902-K, 902-3.2D, 902-3C

9. User Tips
- Always tin your iron tip before and after each use to prevent oxidation and ensure efficient heat transfer.
- Use a damp sponge or brass wool to clean the tip regularly during soldering to remove excess solder and flux residue.
- Avoid applying excessive pressure on the soldering tip; let the heat do the work.
- Ensure adequate ventilation in your workspace to disperse fumes when soldering.
10. Support & Documentation
For more detailed information and comprehensive diagrams, please refer to the official user manual (PDF) available at: YIHUA 926LED-III User Manual (PDF).