Winlinte 988F-9B989-BB

Contents

Winlinte TPS Throttle Position Sensor User Manual

Model: 988F-9B989-BB

Brand: Winlinte

1. Safety Instructions ⚠

Please read all safety instructions carefully before installation or operation to prevent injury or damage.

  1. Park the vehicle on a flat, stable ground, apply the parking brake, and turn off the engine completely.
  2. For all electrical parts, disconnect the vehicle battery negative terminal first to avoid short circuit or electric shock.
  3. Remove the original old or damaged part in reverse order of factory installation, using proper matching tools. Do not force dismantle to avoid damaging surrounding parts.
  4. Clean the installation area thoroughly, check for wear, rust or damage of mounting brackets and related parts, and ensure the mounting surface is flat and clean.
  5. Align the new auto part with the original mounting position, fix it firmly with standard fasteners (screws, bolts, clips), and ensure no looseness or deviation.
  6. Reconnect all wiring harnesses, hoses or connectors correctly. For electrical parts, reconnect the battery after confirming all connections are correct.
  7. Start the vehicle, test the function of the new part, check for abnormal noise, leakage or malfunction, and confirm normal operation before use.
  8. Tools Required: Standard wrench set, screwdriver, jack, safety gloves, voltage tester (for electrical parts).

2. Product Overview

This document provides detailed instructions for the installation and operation of the Winlinte TPS Throttle Position Sensor, model 988F-9B989-BB. This sensor is a direct replacement part designed to ensure accurate throttle response in compatible vehicles.

Product Images

Front view of the TPS sensor, showing part number 988F-9B989-BB.
Front view of the TPS sensor, showing part number 988F-9B989-BB.
Side view of the TPS sensor, showing the connector pins.
Side view of the TPS sensor, showing the connector pins.
Top view of the TPS sensor, showing the part number and connector.
Top view of the TPS sensor, showing the part number and connector.
Angled view of the TPS sensor, showing the rotating mechanism and blue O-ring.
Angled view of the TPS sensor, showing the rotating mechanism and blue O-ring.
Another angled view of the TPS sensor, highlighting the rotating mechanism.
Another angled view of the TPS sensor, highlighting the rotating mechanism.
Bottom view of the TPS sensor, showing the mounting holes and rotating mechanism.
Bottom view of the TPS sensor, showing the mounting holes and rotating mechanism.
Close-up of the sensor's rotating mechanism.
Close-up of the sensor's rotating mechanism.

Product Video

Product demonstration video showing different angles of the TPS sensor.

3. Specifications

AttributeValue
Part Number / OE Number988F-9B989-BB, 988F9B989BB
MaterialABS, OEM Standard
ConditionNew
Sensor TypePiezoelectric
Type (Product Name)TPS Throttle Position Sensor
Fitment TypeDirect Replacement
CertificationCE, E-Mark, RoHS Compliant
Package Weight0.1 kg
Package Dimensions (L x W x H)8 cm x 5 cm x 9 cm

Compatible Vehicle Models

  • Ford EcoSport: 2004-2005 (L4 2.0L Petrol DOHC)
  • Ford Escape: 2001-2004 (L4 2.0L Petrol DOHC), 2005-2008 (L4 2.3L Petrol DOHC)
  • Ford Focus: 2000-2007 (L4 2.0L Petrol DOHC Manual transmission), 2003-2007 (L4 2.3L Petrol DOHC Manual transmission)
  • Ford Ka: 2001 (L4 1.6L Petrol OHV), 2002-2004 (L4 1.6L Petrol SOHC)
  • Ford Mondeo: 2001-2006 (L4 2.0L Petrol DOHC)
  • Ford Ranger: 2002-2011 (L4 2.3L Petrol DOHC)
  • Mercury Mariner: 2005-2007 (L4 2.3L Petrol DOHC)
  • Peugeot 206: 1998-2013 (1.6 16V 1587ccm 109HP 80KW Petrol Hatchback)
  • Peugeot 307: 2000-2008 (1.6 16V 1587ccm 109HP 80KW Petrol Hatchback Estate)

4. Installation & Setup

Professional installation is highly recommended. Improper installation may cause vehicle damage or personal injury. Always follow the safety instructions in Section 1.

  1. Turn off the engine and disconnect the battery negative terminal.
  2. Locate the existing TPS (Throttle Position Sensor) on the throttle body.
  3. Unplug the electrical connector from the old sensor.
  4. Remove the mounting screws that secure the old sensor.
  5. Carefully remove the original TPS from the throttle body.
  6. Install the new Winlinte TPS, ensuring it aligns correctly with the mounting position.
  7. Tighten the mounting screws properly to secure the new sensor.
  8. Reconnect the electrical connector firmly to the new sensor.
  9. Reconnect the battery terminal.

5. Operating Instructions

After successful installation, perform the following steps to ensure proper operation:

  1. Clear any existing fault codes from the vehicle's ECU using an appropriate diagnostic tool. Calibrate the new sensor if required by your vehicle's manufacturer specifications.
  2. Start the engine.
  3. Test the throttle response smoothly. Check for any abnormal noise, leakage, or malfunction.
  4. Ensure the engine idles correctly and responds smoothly to accelerator pedal input.

6. Maintenance

The Winlinte TPS Throttle Position Sensor is designed for long-term reliability and typically requires no routine maintenance. However, it is recommended to:

  • Periodically inspect the sensor and its electrical connector for any signs of wear, corrosion, or damage.
  • Ensure the mounting screws remain tight.
  • Keep the area around the throttle body clean to prevent debris from affecting sensor operation.

7. Troubleshooting

If you experience issues after installing the TPS sensor, consider the following:

  • Check Connections: Ensure all electrical connectors are securely attached and free from corrosion.
  • Clear Fault Codes: Use an OBD-II scanner to check for and clear any diagnostic trouble codes (DTCs).
  • Calibration: Some vehicles may require a specific calibration procedure after TPS replacement. Consult your vehicle's service manual.
  • Inspect for Damage: Visually inspect the sensor and wiring for any physical damage.
  • Professional Diagnosis: If issues persist, it is recommended to seek diagnosis from a qualified mechanic.

8. User Tips

  • Always compare the original OE part number on your old sensor with the new one to ensure compatibility, as vehicle models can have variations.
  • When the original part number is unreadable, confirm compatibility by comparing the appearance of the part with product images or consulting a professional mechanic.
  • Wear personal protective equipment, such as safety gloves, during installation to prevent physical injury.

9. Warranty & Support

Warranty Terms

The product comes with a 12-month warranty covering manufacturing defects only. The warranty does NOT cover damage caused by improper installation, misuse, accident, normal wear, unauthorized modification, or failure to follow instructions.

For warranty claims, please contact customer service with your order number, product photos, and a detailed fault description.

Safety Warnings

  • Do not modify, disassemble, or reprocess this product without authorization, as this may lead to fire, electric shock, or part failure.
  • Do not install the product on flammable surfaces or cover it with heat insulation/flammable materials.
  • Confirm the product is fully compatible with your vehicle model before installation; incorrect fitment is not covered by warranty.

Additional Resources

A user manual in PDF format is available for download: View User Manual (PDF)

10. EU Compliance Information

This product complies with EU Regulation (EU) 2019/1020 and relevant automotive safety standards.

EU Responsible Person:

Name: Alter Agent S.R.L.

Address: Via Paolo Sarpi 11, 20154 Milano MI, Italy

Email: cqzk6653@hotmail.com

Phone: +39 3780423021

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.