Qasim T10 BA9S T5

Contents

Qasim 30 LED Bullbar Indicator Lights User Manual

Model: T10 BA9S T5

1. Introduction

Thank you for choosing the Qasim 30 LED Bullbar Indicator Lights. This manual provides essential information for the safe installation, operation, and maintenance of your new LED lights. Please read all instructions carefully before use.

For a downloadable version of this manual, please refer to the User Manual (PDF).

2. Safety Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture beyond its IP67 rating.
  • Handle with care to avoid cuts or injuries.

3. Package Contents

  • 2 x Front LED Indicator Park Lights
Two Qasim 30 LED Bullbar Indicator Lights
Figure 1: Included LED Bullbar Indicator Lights.

4. Setup and Installation

4.1 Wiring Instructions

The Qasim LED Bullbar Indicator Lights feature a simple 3-wire connection for each unit:

  • Black Wire: Connects to Negative / Ground.
  • White Wire: Connects to Front Clearance / Parking Light positive.
  • Yellow Wire: Connects to Indicator / Turn Signal positive.
Wiring diagram for Qasim LED lights
Figure 2: Wiring Diagram. Ensure correct polarity and connections.

4.2 Mounting

These lights are designed for easy installation. They are typically mounted on bullbars or other flat surfaces using the integrated mounting holes. Ensure the mounting surface is clean and secure.

Rear view of Qasim LED lights showing mounting points and wire exit
Figure 3: Rear view of the lights, showing the mounting tabs and wire routing.

4.3 Installation Steps

  1. Ensure the vehicle's power is off before beginning installation.
  2. Identify the desired mounting location and ensure it is flat and provides adequate space.
  3. Secure the lights using appropriate fasteners through the mounting holes.
  4. Connect the wires according to the wiring diagram (Section 4.1). Ensure all connections are secure and insulated.
  5. Test the lights by turning on the vehicle's power and activating the parking lights and turn signals.

The product is designed for "Plug and Play" installation, meaning no complex modifications are typically required if the wiring points are accessible.

5. Operating Instructions

The Qasim 30 LED Bullbar Indicator Lights provide dual functionality:

  • Front Clearance / Parking Light (White): When connected to your vehicle's parking light circuit, the white LEDs will illuminate, providing front clearance visibility.
  • Indicator / Turn Signal (Amber): When connected to your vehicle's turn signal circuit, the amber LEDs will flash, indicating your intended direction.
Qasim LED lights showing Front Clearance, Full On, and Indicator modes
Figure 4: Light modes: Front Clearance (White), Full On (both white and amber if wired for DRL/park), and Indicator (Amber).

6. Maintenance

These LED lights are designed for durability and minimal maintenance. They feature an IP67 waterproof and dustproof rating, ensuring reliable performance in various weather conditions.

Qasim LED light being splashed with water, illustrating IP67 waterproof feature
Figure 5: IP67 Waterproof & Dustproof rating ensures durability.
  • Cleaning: Periodically clean the lens with a soft, damp cloth to remove dirt and debris that may obstruct light output. Avoid abrasive cleaners.
  • Inspection: Occasionally check wiring connections for any signs of corrosion or damage.

7. Troubleshooting

ProblemPossible CauseSolution
Light does not illuminateNo power, incorrect wiring, faulty connection, blown fuse.Check power supply to the wires. Verify wiring connections (positive/negative). Inspect vehicle's fuse for the relevant circuit.
Light flickers or is dimLoose connection, insufficient voltage, corrosion on terminals.Ensure all wire connections are tight. Check vehicle's voltage supply. Clean any corroded terminals.
Only one function works (e.g., only white, no amber)Incorrect wiring for the non-working function.Re-check the wiring for the specific function against the diagram (Section 4.1).

8. Specifications

FeatureDetail
BrandQasim
ModelT10 BA9S T5
Item TypeParking Lights / Indicator Lights
Voltage12V
LED Quantity30 LEDs (15 White + 15 Amber)
Light ColourAmber, White
Protection RatingIP67 Waterproof and Dustproof
OriginMainland China
High-concerned chemicalNone
Package Length15 cm
Package Width8 cm
Package Height3 cm
Package Weight0.6 kg

9. User Tips

  • Verify Dimensions: Before purchasing or installing, it is recommended to measure the intended mounting area to ensure these lights (approx. 15cm length) will fit properly.
  • Secure Wiring: Use heat shrink tubing or electrical tape to properly insulate and secure all wire connections to prevent short circuits and corrosion, especially in outdoor environments.

10. Warranty and Support

For any questions, technical support, or warranty inquiries, please contact your seller directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.