JETTING AY16

Contents

Human Body Motion Sensor Spot LED Downlight Instruction Manual

Model: AY16

1. Product Overview

The AY16 Human Body Motion Sensor Spot LED Downlight is an energy-efficient lighting solution designed for various indoor spaces. It features an integrated motion sensor for automatic on/off functionality, providing convenience and energy savings. This downlight is available in 5W, 7W, and 9W power options, emitting a cold white light.

Three types of downlights: standard, motion sensor, and empty fixture

Figure 1: Product variations including the motion sensor model.

Three different sizes of motion sensor downlights

Figure 2: Available sizes of the motion sensor downlight.

2. Safety Information

  • Always ensure the power supply is turned off before installation or maintenance.
  • Consult a qualified electrician for installation if you are unsure.
  • Handle the downlight with care to avoid breakage, as it is fragile.
  • Keep the light dry and avoid exposure to moisture.
  • Do not use abrasive materials for cleaning.

3. Installation Guide

Quick Start Guide:

  1. Power Off: Ensure the main power supply to the installation area is turned off at the circuit breaker.
  2. Prepare Opening: Ensure the ceiling hole size is appropriate for the downlight model (refer to specifications).
  3. Connect Wiring: Connect the 2-pin wire from the downlight to your household electrical wiring. Typically, this involves connecting the live and neutral wires. If unsure, consult a qualified electrician.
  4. Secure Downlight: Gently push the spring clips on the sides of the downlight upwards and insert the fixture into the ceiling opening. Release the clips to secure the downlight in place.
  5. Test Functionality: Turn on the power supply to test the light functionality.
  6. Adjust Position: Adjust the position of the downlight for optimal lighting and motion detection coverage.
Back of the downlight showing wiring and spring clips for installation

Figure 3: Rear view of the downlight with wiring and mounting clips.

Warning: Installation should only be performed by qualified personnel if you are not familiar with electrical wiring.

4. Operating Instructions

This downlight features a built-in human body motion sensor for smart operation:

  • Automatic ON: The light will automatically turn on when motion is detected within its sensing range.
  • Automatic OFF: The light will automatically turn off approximately 20-40 seconds after the person leaves the sensing area or no motion is detected.
Child in a hallway with blue arcs indicating motion sensor activation

Figure 4: Illustration of motion sensor detection in a hallway.

Downlights installed in various room settings: living room, corner, and closet

Figure 5: Examples of downlight application in different indoor environments.

5. Maintenance

  • Cleaning: To clean the downlight, ensure the power is off. Wipe the surface with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or electronic components.
  • Moisture: Keep the light dry and avoid exposure to excessive moisture or direct water spray.
  • Bulb Replacement: This LED downlight has a long lifespan (up to 50,000 hours) and does not require frequent bulb replacement. The LED module is integrated and not user-replaceable.

6. Troubleshooting

If your downlight is not functioning as expected, consider the following:

  • No Light:
    • Check if the power supply is on.
    • Verify that the wiring connections are secure.
    • Ensure the circuit breaker has not tripped.
  • Light Stays On/Off:
    • Ensure there are no constant movements within the sensor's range that might keep it on.
    • Check if the sensor is obstructed or covered.

If problems persist after checking these points, please contact customer support.

7. Specifications

FeatureDetail
ModelAY16
Power Options5W, 7W, 9W
Light ColorCold White (6000-6500K)
Input VoltageAC220V
Beam Angle120 degrees
MaterialPlastic
LED Working Temperature-25°C to +70°C
Luminous Efficiency> 85
LifespanUp to 50,000 hours
Motion Sensor Delay20-40 seconds after no motion
Package Contents1x LED Downlight with 2-pin wire (No power plug included)

Dimensions (7W Model Example):

  • Hole Size: 93-110mm
  • Panel Diameter: 117mm
  • Height: 25mm
Diagram showing dimensions for the 7W model: hole size 93-110mm, panel diameter 117mm, height 25mm, color temperature 6500k

Figure 6: Detailed dimensions for the 7W downlight model.

8. User Tips

No specific user tips were available from reviews or Q&A for this product. General tips for motion sensor lights include:

  • Placement: Install in areas where motion is expected, such as hallways, closets, stairwells, or utility rooms, for optimal energy saving and convenience.
  • Clearance: Ensure the sensor is not obstructed by furniture or other objects to maintain effective motion detection.

9. Support

For any issues, questions, or technical support regarding your JETTING AY16 Human Body Motion Sensor Spot LED Downlight, please contact the store support where you purchased the product.

A detailed user manual in PDF format is also available for download from the product page.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.