Quansheng UV-K5(8)

Contents

Quansheng UV-K5(8) Dual Band Walkie Talkie User Manual

Model: UV-K5(8) / UV-K6

1. Introduction

Thank you for choosing the Quansheng UV-K5(8) Dual Band Walkie Talkie. This device is a high-performance, multi-functional two-way radio designed for reliable communication across various environments. This manual provides essential information for the safe and effective operation, setup, and maintenance of your radio.

Note: The UV-K6 and UV-K5(8) are the same product. Model number labels are assigned randomly during packaging. This version is the V3 standard version and does not support firmware flashing or expanded storage.

Quansheng UV-K5(8) Walkie Talkie

Figure 1: Quansheng UV-K5(8) Dual Band Walkie Talkie

2. Safety Information and Precautions

2.1. FCC Compliance Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device. If this equipment does cause harmful interference to radio or television reception, try to correct the interference by reorienting or relocating the receiving antenna, increasing separation between equipment and receiver, connecting equipment to a different circuit, or consulting a dealer.

This device complies with FCC radiation exposure limits for an uncontrolled environment. Hold this transmitter approximately 25 mm away from your face and speak normally with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration.

WARNING: Modification of this device to receive cellular radiotelephone service signals is prohibited under FCC rules and federal law.

2.2. CE Warning

Use the two-way radio in environments with temperatures between 0-40°C; otherwise, it may damage the radio. It can operate under 2000m. This radio equipment type complies with Directive 2014/53/EU.

2.3. General Precautions Before Using

  • Keep the radio and accessories out of reach of children.
  • Maintenance should only be performed by professional technicians.
  • Use only the standard battery pack and charger to avoid damaging the radio.
  • Use the standard antenna to ensure optimal communication distance.
  • Avoid prolonged exposure to direct sunlight or heat sources.
  • Do not expose the radio to extreme dust or wet environments.
  • Do not clean the radio with harsh chemical products, cleaning agents, or strong washing agents.
  • Do not transmit when the antenna is not installed.
  • If you detect unusual smells or smoke, immediately turn off the radio, remove the battery, and contact your agent.

3. Package Contents

Carefully unpack your portable radio and check the following items before discarding the packing materials:

ItemQuantity
Portable Radio1
Antenna1
Li-ion Battery1
Belt Clip1
Hand Strap1
Type-C Charger Cable1
Product Manual1
Box1
Standard Package Contents

Figure 2: Standard Package Contents (Radio, Antenna, Battery, Back Clip, Charger Cable, Lanyard, Manual, Box)

4. Product Diagram and Parts Identification

UV-K5(8) Parts Diagram

Figure 3: UV-K5(8) Walkie Talkie Parts Diagram

  1. Antenna: For transmitting and receiving radio signals.
  2. Jack Light: Indicator light.
  3. Power/Volume Switch: Rotate clockwise to power on and increase volume; rotate counter-clockwise to decrease volume and power off.
  4. LCD Screen: Displays operational status, frequency, channel, and other information.
  5. Indicator: LED status indicator.
  6. MENU (Confirm Key): Accesses and confirms menu selections.
  7. UP/Down Key: Navigates through menus and adjusts settings.
  8. Exit Key: Exits current menu or function.
  9. Speaker: Outputs audio.
  10. Keypad: For manual frequency input, channel selection, and function access.
  11. Microphone: For voice input during transmission.
  12. Microphone/Programming Jacks: Connects external microphone/headset or programming cable.
  13. Type-C Charging Port: For emergency charging.
  14. Transmitting Key (PTT): Press to transmit, release to receive.
  15. Side Key 1: Programmable function key.
  16. Side Key 2: Programmable function key.

5. Setup

5.1. Battery Installation and Charging

Your radio comes with a Li-ion battery. Battery packs are not fully charged when shipped; charge them before first use.

Battery Installation:

Align the battery pack with the grooves on the back of the radio and slide it upwards until it clicks into place. To remove, press the release latch and slide the battery downwards.

Charging Notes:

  • Initially charging the battery pack after purchase or extended storage (longer than 2 months) may not bring it to full capacity immediately. Full capacity is typically achieved after two or three charge/discharge cycles.
  • Do not operate the radio during charging, as this can affect normal charging and potentially damage the battery.
  • Once fully charged, remove the battery from the charger. Avoid recharging before the battery is completely depleted to prevent memory effect.
  • If the battery capacity or operating time significantly decreases, it indicates the battery is nearing its end of life and should be replaced.
  • Use only original factory battery packs and chargers.

Type-C Charging Instructions:

The Type-C port is primarily for emergency charging. For regular charging, use a dedicated charger base (if available for your model).

  • When charging via Type-C, a "" logo appears on the screen during startup.
  • Charging continues even if the radio is powered off.
  • A blue light indicates charging is in progress; a blinking blue light indicates charging is nearing completion. The blue light turns off when charging is complete.
  • Do not remove the battery during Type-C charging.
  • Important: Do not transmit while the radio is charging (via charger or Type-C) to prevent damage. Receiving performance may also be affected during charging.

5.2. Antenna Installation

Screw the antenna clockwise into the connector on the top of the radio until it is firmly seated. Do not overtighten.

6. Operating Instructions

6.1. Power On/Off and Volume Control

Rotate the Power/Volume Switch (3) clockwise to turn on the radio. Continue rotating clockwise to increase the volume. Rotate counter-clockwise to decrease the volume and turn off the radio.

6.2. LCD Display

The LCD screen (4) displays various symbols and information:

  • Signal Strength: Bars indicate signal strength.
  • HML: Transmitting Output Power Indicator (High, Medium, Low).
  • CT/DCS: Indicates CTCSS/DCS code is active.
  • VOX: Voice Operated Transmission function is active.
  • DTMF: DTMF signal decoding is active.
  • DW: Dual Watch function is active.
  • Battery Icon: Shows current battery level; blinks when low.
  • Keypad Lock: Indicates keypad is locked.
  • SCR: Voice encryption is active.
  • R: Reverse mode (receive and transmit frequencies are reversed).
  • WX: Cross-Band Receiving/Transmitting.
  • RX/TX: Receiving/Transmitting status.
  • Type-C Charging Mark: Indicates Type-C charging is active.
  • AM: AM receiving mode.
  • NS: NOAA channel automatic scan.

6.3. Keypad Functions

  • PTT Key (14): Press to transmit, release to receive.
  • MENU (6): Short press to enter menu, select item, and confirm. Long press to enter the last setting item.
  • UP/Down Keys (7): Navigate menu options, adjust values.
  • EXIT (8): Short press to exit current menu/status. Long press to return to main page.
  • * Key: Short press to enter manual dial/call page. Long press to start frequency or channel scanning.
  • # Key: Long press to lock/unlock the keypad.
  • F Key: Works with 0-9 and * to quickly access functions.
  • Side Keys (15, 16): Programmable via software. Default functions may include Monitor, Jacklight, Emergency Alarm, 1750Hz Tone.

6.4. Menu Navigation and Settings

Press the MENU key to enter the menu. Use the UP/Down keys to select menu items. Press MENU again to confirm your selection. Press EXIT to go back one level or long press EXIT to return to the main screen.

Key Menu Items:

  • SQL (Squelch Level): 0-9 (0=open, 9=tightest).
  • STEP (Step Frequency): 2.5K/5K/6.25K/10K/12.5K/25K.
  • TXP (Output Power): LOW/MID/HIGH.
  • R_DCS/R_CTCS (Receive DCS/CTCSS): Set receive codes.
  • T_DCS/T_CTCS (Transmit DCS/CTCSS): Set transmit codes.
  • SFT-D (Frequency Deviation Setting): OFF/TX/ADD/SUB.
  • OFFSET (Frequency Deviation): 0-999.9999M.
  • W/N (Channel Bandwidth): WIDE/NARROW.
  • SCR (Scrambler): 1-10 (10 groups).
  • BCL (Busy Channel Lock): ON/OFF.
  • MEM-CH (Channel Save): Save current frequency/settings to a channel.
  • SAVE (Battery Save): OFF/1:1/1:2/1:3/1:4.
  • VOX (VOX Setting): OFF/1-10.
  • ABR (Auto Backlight): 1-5 seconds.
  • TDR (Dual-watch): ON/OFF.
  • WX (Cross-Band): ON/OFF.
  • VOICE (Voice Prompt): CHI/ENG.
  • MDF (Channel Display Mode): FREQ/CH/NAME.
  • AUTOLK (Auto Keypad Lock): ON/OFF.
  • 1-CALL (One Key Call Channel): Set a quick access channel.
  • DEL_CH (Channel Delete): Delete a stored channel.
  • RESET: VFO (reset VFO parameters only) / ALL (reset all parameters).

6.5. Main Features and Operations

Power On Password Protection:

If enabled, the radio will display "LOCK" on startup. Enter the password to operate.

Switch Main Channel:

Press F+2 to switch between main channels. The solid arrow indicates the active main channel.

Dual Band Single-Watch/Dual-Watch:

Set via MENU→17. Allows monitoring two frequencies simultaneously.

Frequency/Channel Mode Switch:

Press F+3 to toggle between Frequency Mode (VFO) and Channel Mode (MR). In VFO mode, you can manually input frequencies. In MR mode, you select stored channels.

Cross-Band Receiving/Transmitting:

Set via MENU→18. Allows communication between different frequency bands.

Channel Save/Delete:

In VFO mode, set your desired frequency and parameters. Press MENU→13, select a channel number, and press MENU again to save. To delete, press MENU→50, select the channel, and press MENU again.

Receiving/Transmitting CTCSS/DCS:

Set via MENU→4 (R-DCS), MENU→5 (R-CTCS), MENU→6 (T-DCS), MENU→7 (T-CTCS). These codes filter out unwanted signals.

Fast Copy One Channel (Frequency Meter):

Press F+4. The radio enters frequency meter mode. Point it at another radio transmitting a strong signal. The LCD will display the carrier frequency and CTCSS/DCS. Press MENU to save.

Set the receiving frequency, then press F+* to start searching. The radio will display the found TX CTCSS/DCS signal. Press MENU to save.

DTMF Functions:

Supports individual, group, and all calls. Manual dialing: Press PTT and keypad numbers. Automatic dialing: Press *, enter 3 digits, then PTT.

Scanning:

Long press * key to start/stop scanning. You can scan frequencies or stored channels. Use UP/Down keys to change scan direction.

Emergency Alarm:

Programmable via software. Activates local audible alarm and/or remote alarm. Exit with any key.

FM Radio:

Press F+0 to enter FM radio mode. Use UP/Down keys to change frequency/channels. Press F+1 for VFO/MR, F+2 for auto scan, F+3 for manual scan.

NOAA Weather Alert:

Press F+5 to enter/exit NOAA Weather Alert. This radio can receive 10 NOAA channels.

Keypad Locking:

Long press the # key to lock/unlock the keypad. Side keys remain functional.

Wireless Radio Replication:

Hold PTT + Side Key 2 to enter. Both radios must be on the same frequency. Press EXIT on receiving radio, MENU on transmitting radio to start.

Wireless Copy Frequency:

Wireless Copy Frequency Feature

Figure 4: Wireless Copy Frequency - Automatically scans and copies other walkie-talkie frequencies.

Frequency Range:

Frequency Range 144-148MHz / 420-450MHz

Figure 5: Operating Frequency Range: 144-148MHz / 420-450MHz.

FM/AM Reception:

FM/AM Reception

Figure 6: Supports FM and AM reception for various communication needs.

10-Group Scrambler:

10-Group Scrambler

Figure 7: Enhances communication privacy with 10 scrambling groups.

DTMF Functionality:

DTMF Function

Figure 8: DTMF can be configured with an identification code, preventing unwanted interruptions (Individual, Group, All calls).

NOAA Weather Functions:

NOAA Weather Functions

Figure 9: Receives NOAA weather broadcasts (162.400-162.550MHz).

200 Channel Memory:

200 Channel Memory

Figure 10: Stores up to 200 channels for convenient and fast access.

LED Flashlight:

LED Flashlight

Figure 11: Built-in LED flashlight for low-light scenarios.

7. Maintenance

7.1. Battery Care

  • Always use the original battery and charger.
  • Avoid overcharging or fully discharging the battery frequently to prolong its lifespan.
  • Store batteries in a cool, dry place when not in use.

7.2. Cleaning

  • Clean the radio's surface with a soft, damp cloth.
  • Do not use harsh chemicals, solvents, or abrasive cleaners.
  • Ensure the radio is dry before use or storage.

8. Troubleshooting

  • No Power: Check if the battery is properly installed and charged. Ensure the power switch is turned on.
  • Cannot Transmit: Check if the antenna is properly attached. Ensure you are on a valid frequency/channel. Check battery level.
  • Poor Reception/Transmission: Check antenna connection. Ensure you are within range. Check for obstructions. Verify CTCSS/DCS settings match.
  • Keypad Unresponsive: Check if the keypad lock is activated (long press # key to unlock).
  • Radio Malfunction: Try performing a factory reset (MENU→51→RESET→ALL). If issues persist, contact customer support.

9. Specifications

General Specifications
Channels200
Frequency Stability±1ppm
Dimensions (H×W×D)115mm × 60mm × 37.5mm
Weight234g
Operating Temperature-20°C to +60°C
Antenna Impedance50Ω
NOAA Channels10
Battery Capacity1600mAh
Audio Power≥0.5W
Audio Distortion≤10%
Transmitting Specifications
Frequency Range (FCC)VHF: 144-148MHz, UHF: 420-450MHz
Output Power≤5W
Emission Current≤1.5A
Max Frequency Deviation≤5KHz (25KHz), ≤2.5KHz (12.5KHz)
Modulation Distortion≤5%
Stray Power≤7.5uW
Adjacent Channel Power70dB (25KHz), 60dB (12.5KHz)
Residual Modulation40dB
Receiving Specifications
Sensitivity (FM, 12dB SINAD)F1 (50-76MHz): -121dBm
F2 (108-135.9975MHz): -121dBm
F3 (136-173.9975MHz): -123dBm
F4 (174-349.9975MHz): -123dBm
F5 (350-399.9975MHz): -123dBm
F6 (400-469.9975MHz): -123dBm
F7 (470-599.9975MHz): -121dBm
WFM (20dB SINAD)WFM (76-108MHz): -110dBm
AM (10dB S/N)F2 (108-135.9975MHz): -113dBm

All stated specifications are subject to change without notice or obligation.

10. User Tips

  • The Quansheng UV-K5(8) (V3 version) is noted for its excellent performance.
  • Ensure the radio is fully charged before extended use, especially since it uses a Type-C cable for charging (a dock might not be included).
  • Always check the specific version (V3 standard) as it does not support firmware flashing or expanded storage.

11. Warranty and Support

For warranty claims, technical support, or service inquiries, please contact your original point of purchase or the authorized dealer. Keep your proof of purchase for warranty validation.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.