TAIYEDQ DL9-40

Contents

TAIYEDQ DL9-40 Miniature Circuit Breaker User Manual

Model: DL9-40

1. Introduction

Thank you for choosing the TAIYEDQ DL9-40 Miniature Circuit Breaker. This device is designed to provide reliable overload and short-circuit protection for electrical circuits in residential, commercial, and industrial applications. Its ultra-thin design and robust construction ensure safety and longevity. Please read this manual carefully before installation and operation to ensure proper use and to prevent potential hazards.

2. Safety Information

WARNING: Electrical shock hazard. Installation and servicing should only be performed by qualified personnel.

  • Always disconnect power at the main supply before installing, servicing, or removing the circuit breaker.
  • Ensure that the circuit breaker's ratings (voltage, current, number of poles) match the requirements of the circuit it is protecting.
  • Do not use the circuit breaker in environments exceeding its specified operating conditions (temperature, humidity).
  • Never attempt to bypass or tamper with the circuit breaker's protective mechanisms.
  • Ensure all connections are tight and secure to prevent overheating and fire hazards.
  • This device is designed for protection against overcurrents due to overload and short-circuit; it does not protect against electric shock in all circumstances.

3. Product Overview

The TAIYEDQ DL9-40 series miniature circuit breakers are available in 1-pole (1P), 2-pole (2P), 3-pole (3P), and 4-pole (4P) configurations to suit various circuit requirements. They feature a flame-retardant material construction for enhanced safety and a long anti-aging life.

Front view of 1P, 2P, 3P, and 4P TAIYEDQ DL9-40 miniature circuit breakers.
Figure 1: TAIYEDQ DL9-40 Miniature Circuit Breakers (1P, 2P, 3P, 4P)

3.1 Status Indicator

Each circuit breaker is equipped with a color indicator bar to show its operational status:

  • Green Prompt Window: Indicates the circuit breaker is in the open state (OFF).
  • Red Prompt Window: Indicates the circuit breaker is in the closed position (ON) or has tripped due to a fault.
Close-up of two circuit breakers showing the green (open state) and red (closed position) prompt windows.
Figure 2: Status Indicator Windows (Green for Open, Red for Closed/Fault)

4. Setup and Installation

Installation must be carried out by a qualified electrician in accordance with national and local electrical codes.

  1. Power Disconnection: Before starting any work, ensure that the main power supply to the circuit is completely disconnected and locked out.
  2. Mounting: The DL9-40 circuit breaker is designed for DIN rail mounting. Snap the breaker onto the DIN rail securely.
  3. Wiring:
    • Connect the incoming live wire(s) to the top terminals and the outgoing live wire(s) to the bottom terminals.
    • For multi-pole breakers (2P, 3P, 4P), ensure correct phase sequence if applicable.
    • Tighten all terminal screws firmly to the specified torque to ensure good electrical contact and prevent loose connections.
  4. Verification: After wiring, double-check all connections for correctness and tightness.
  5. Power Restoration: Once installation is complete and verified, restore power to the main supply.

5. Operating Instructions

  1. Turning On: To energize the circuit, push the toggle switch upwards to the 'ON' position. The indicator window will show RED.
  2. Turning Off: To de-energize the circuit, push the toggle switch downwards to the 'OFF' position. The indicator window will show GREEN.
  3. Tripping: In the event of an overload or short-circuit, the circuit breaker will automatically trip to protect the circuit. The toggle switch will move to an intermediate or 'OFF' position, and the indicator window will show RED (if it was previously ON).
  4. Resetting After a Trip:
    1. First, identify and rectify the cause of the trip (e.g., unplug overloaded appliances, fix short circuits).
    2. Push the toggle switch fully to the 'OFF' position (downwards) until the indicator shows GREEN.
    3. Then, push the toggle switch upwards to the 'ON' position. The indicator will show RED.
    4. If the breaker trips again immediately, do not attempt to reset it repeatedly. There is a persistent fault that needs professional attention.

6. Maintenance

  • Periodic Inspection: Regularly inspect the circuit breaker for any signs of physical damage, discoloration, or loose connections.
  • Cleaning: Keep the circuit breaker clean and free from dust and debris. Use a dry, non-abrasive cloth for cleaning. Ensure power is off before cleaning.
  • No User-Serviceable Parts: The DL9-40 circuit breaker contains no user-serviceable parts. Do not attempt to open or repair the unit. If it is damaged or malfunctioning, it should be replaced by a qualified electrician.

7. Troubleshooting

ProblemPossible CauseSolution
Circuit breaker trips frequentlyOverload, short circuit, faulty appliance/wiringReduce load, check for short circuits, inspect appliances/wiring. Consult an electrician if problem persists.
Circuit breaker does not resetPersistent fault, internal damage to breakerEnsure fault is cleared. If it still won't reset, replace the breaker. Consult an electrician.
No power to circuit, breaker is ONLoose connection, faulty breaker, upstream power issueCheck connections, test breaker (by electrician), check main supply/upstream breakers.

8. Specifications

FeatureSpecification
Model NumberDL9-40
Brand NameTAIYEDQ
Rated Voltage220V
Rated Current Options6A, 10A, 16A, 20A, 25A, 32A, 40A
Poles Number Options1P, 2P, 3P, 4P
TypeMiniature Circuit Breaker
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
Smart DeviceNo
Wireless FunctionalityNo
Battery IncludedNo
OriginMainland China
Height81mm
Width (per pole)9mm (1P: 9mm, 2P: 18mm, 3P: 27mm, 4P: 36mm)
Diagram showing the dimensions of the circuit breakers: 81mm height, and widths of 9mm (1P), 18mm (2P), 27mm (3P), 36mm (4P).
Figure 3: DL9-40 Circuit Breaker Dimensions

9. User Tips

  • Always ensure the circuit breaker's rated current matches the circuit's design load to prevent nuisance tripping or inadequate protection.
  • Avoid overloading circuits by plugging too many high-power appliances into a single circuit.
  • If a circuit breaker trips repeatedly, it indicates a persistent issue. Do not ignore it; consult a qualified electrician to diagnose and resolve the problem.
  • For more detailed technical information and diagrams, please refer to the official user manual PDF provided by the manufacturer.

10. Frequently Asked Questions (FAQ)

Q: What does it mean if the indicator window is red?
A: A red indicator means the circuit breaker is either in the 'ON' (closed) position or it has tripped due to an overload or short-circuit. If it's tripped, the toggle switch will likely be in an intermediate or 'OFF' position.
Q: Can I install this circuit breaker myself?
A: For safety reasons and to ensure compliance with electrical codes, installation should always be performed by a qualified and licensed electrician.
Q: What should I do if the breaker keeps tripping?
A: Repeated tripping indicates a serious issue such as a persistent overload or a short circuit. Unplug all devices from the affected circuit and try resetting. If it still trips, do not use the circuit and contact an electrician immediately.

11. Warranty and Support

For any technical assistance, warranty claims, or support inquiries, please contact your seller or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.