TiESFONG A99UB

Contents

TiESFONG A99UB 4-Channel GPS Dash Cam User Manual

Please read before using and keep it for future use.

1. Safety Information and Precautions

1.1 General Security Guidelines

  1. Read this user manual carefully before using the dash cam. It contains important safety, operating, and maintenance instructions.
  2. Follow all safety precautions to prevent damage due to improper use.
  3. Avoid extended exposure to direct sunlight or extreme temperatures (high or low) to prevent degradation or damage to the unit and its functionality.
  4. Do not attempt to open the cover or repair the device yourself. For accessory issues, contact the seller.
  5. Use the dash cam only as intended. Do not use it in any way that is illegal, physically damaging, or poses a danger to vehicle operation or occupants.
  6. Do not operate or install the dash cam while driving, or attempt to change settings.
  7. Do not connect the uninterruptible power supply without authorization; this may cause vehicle or product failure. Consult a professional for installation.
  8. Stop using or remove the dash cam when cleaning or repairing the car.
  9. Do not install the dash cam in a location that obstructs or reduces the driver's view. Ensure usage complies with local vehicle codes.

1.2 Precautions on Usage

  1. Before installation, check all accessories to ensure the product and accessories are correct and complete.
  2. To ensure optimal performance, format the micro SD card before first use.
  3. During installation, do not insert the car key into the power supply, and do not insert or remove any accessories (like micro SD card or rear cam) while the dash cam is powered on. Perform these actions only when power is turned off.
  4. The dash cam screen provides a preview, not the original views. For best viewing, plug the memory card into a computer. Turn off the dash cam before removing the memory card.
  5. Examine, check, and verify the dash cam and memory card at least every 3 months to ensure proper video reception and recording. Verify that the unit, visible lights, and audible sounds are working normally before each use.
  6. If the TsCam APP cannot connect for preview on some mobile phone models, turn on airplane mode on your mobile phone and try again.

2. Setup Guide

2.1 What's in the Box

The package contents are as follows:

Package Contents: A99UB Dash Cam, S20U Rear Cam, GPS Cable, P7 Hardwire Kit, User Manual, Fuse Connecting Cable, Memory Card (Optional), Electrostatic Sticker, Accessories.
Figure 2.1: Package Contents
  1. A99UB Dash Cam: Main recording unit.
  2. S20U Rear Camera: With 18 ft cable.
  3. TIESFONG P7 Hardwire Kit: 8.53 ft cable for power connection.
  4. Fuse Connecting Cable: 0.98 ft.
  5. Type-C USB Backup Cable: 1.97 ft.
  6. Micro SD Card (Optional): For storage.
  7. User Manual: This document.
  8. Accessories: Including electrostatic stickers and installation tools.

2.2 Product Overview

Familiarize yourself with the dash cam components:

Diagram of the A99UB Dash Cam with numbered parts indicating various ports, buttons, and cameras.
Figure 2.2: Dash Cam Components
No.NameDescription
1POWERType-C USB port for power on
2TF Card SlotFor inserting TF Card (Micro SD Card)
3RESETReset the recorder
4REARJack slot for 2.5mm round hole for connecting Rear Cam
5Screen3.16 inch Screen (tear off protective film before use)
6Indicator LightBlue light always bright: powered on (not recording). Blue light blinking: recording in progress.
7Power ButtonFunction varies by page; see 'Functional Explanation'.
8M ButtonFunction varies by page; see 'Functional Explanation'.
9Up ButtonFunction varies by page; see 'Functional Explanation'.
10Down ButtonFunction varies by page; see 'Functional Explanation'.
11OK ButtonFunction varies by page; see 'Functional Explanation'.
12Radar Switch & Working LightControls radar and indicates status.
13Radar SensorSenses moving objects after car power off.
14Radar Sensor LightIndicates radar sensing activity.
15Left/Right CamLeft/Right Cameras (tear off protective film before use)
16Infrared LED Light4 IR LED lights enhance night vision in car.
17Front CamFront Facing Camera for video recording road events (tear off protective film before use)

2.3 Memory Card Installation

  1. Insert a new Micro SD card into the card slot and power on the dash cam.
  2. On the dash cam, navigate to the 'Format' option in the menu and confirm to format the card.
  3. A blue frame will appear with "please wait...". Be patient during formatting.
  4. Once formatting is complete, a '√' icon will be displayed.
  5. Press the M button to return to the recording interface; the dash cam will automatically start recording.

Memory Card Requirements:

  • Use a genuine Micro SD card (64GB-256GB MAX) of Class 10, U3 Speed or above.
  • Recommended: LEXAR High Endurance TF cards.
  • Insert or remove the Micro SD card only when the dash cam is turned off.
  • Do not remove the card while recording to prevent loss of important video files.

2.4 Dash Cam and Bracket Installation

  1. Align the mount with the dash cam mount interface and push it from right to left until it clicks into place.
  2. Tear off the red protective film on the 3M Stick Bracket.
  3. Attach the bracket to an Electrostatic Sticker, press firmly for 10-20 seconds to ensure a secure fit.
  4. Verify the installation by looking through the outside glass of the car to confirm it is fully fitted.

Electrostatic Stickers:

  • Function: Protects the car windshield or window film.
  • Paste Method:
    1. Confirm the installation position and wipe the area with screen cleaning paper.
    2. Tear off the protective film and stick it on the selected position.
    3. Use a scraper to remove air bubbles between the sticker and the glass.
  • Important: Stick it on a flat surface without air bubbles for firm adhesion.

2.5 Power Cord Installation

Connecting the Hardwire Kit:

The P7 Hardwire Kit can be connected to either the Fuse Box or via an OBD connector (OBD connector not included in package).

Diagram showing the hidden installation of the dash cam and wiring route along the windshield edge.
Figure 2.3: Hidden Installation Diagram
  1. Connect the Type-C USB port of the P7 Hardwire Kit to the power port of the dash cam.
  2. Tape the black box of the hardwire kit to the top of the car's front windshield.
  3. Use a pry bar to carefully run the power cord along the slit on the edge of the windshield and hide it inside the car's trim.
  4. Start your car; the dash cam will automatically power on and begin recording.

Fuse Box Connection:

  1. Ensure the 3-core Fuse Connecting Cable is fully connected to the P7 Hardwire Kit.
  2. Connect the fuse wire to the corresponding connector in your car's fuse box. (Refer to your car's owner's manual to locate the fuse box).
  3. Important: Connect to a fuse slot under 15A.
Diagram showing the fuse box connection for the hardwire kit.
Figure 2.4: Fuse Box Wiring
  • For ACC Box (Connect with Red Wire): Connect the red wire of the hardwire kit to the positive pole of an ACC fuse slot. ACC fuse slots energize only when the ignition is on. Test with a tester bulb: it lights when the engine is on and turns off when the engine is off.
  • For BAT+ Box (Connect with Yellow Wire): Connect the yellow wire of the hardwire kit to the positive pole (BAT+) of a constant fuse slot. Select a constant current interface below 15A with no other equipment using electricity. Test with a voltage tester to ensure it has electricity even when the car engine is off.

Rear Camera Power Cable:

  1. Confirm the BMW 4/5-pin connector between the Rear Cam Cable and Power Cable is fully connected.
  2. Insert the 2.5mm round hole interface of the Rear Cam into the 'Rear' jack slot of the dash cam.
  3. Use a pry bar to run the power cord along the gap in the roof and hide it up to the rear windshield inside the car.
  4. Confirm the position of the Rear Cam, then tear off the protective film from its bracket and stick it on.

Recommendation: Select a position close to the center of the rear windshield, avoiding the defogging line, to prevent affecting video quality.

Note: The rear cam is non-waterproof and must be mounted inside the car.

2.6 Test Your Installation

  1. Connect the power cable to the Dash Cam to ensure the device powers on and works normally.
  2. Finally, hide any extra cables for a neat installation.

3. Operating Instructions

3.1 Power ON/OFF

  • Manually: Long press the power button to turn it ON or OFF.
  • Automatically: The dash cam will power off if the power cable is disconnected or the vehicle is turned off.

3.2 Main Page Details (Icons and Functions)

The upper and lower information columns on the main page will automatically hide after 6 seconds of inactivity. Press any key to activate them.

Main page display of the dash cam showing various icons and information like GPS, WiFi, recording status, and speed.
Figure 3.1: Main Page Interface

Icon Explanation:

  • Memory Card: Green icon indicates card inserted/correct; Red icon indicates no card/error.
  • Loop Record Time: Icons indicate 1, 2, or 3 minutes loop recording.
  • G-Sensor: Icons indicate OFF, ON (Low), ON (Medium), ON (High).
  • GPS Tracking: Icons indicate OFF, ON but not connected, ON and connected.
  • IR LED Light: Icons indicate OFF, always-ON, or automatic-ON.
  • Emergency Lock: Icon indicates lockout not triggered or triggered. If triggered, the locked icon appears in the center, and the video is saved in the event folder.
  • Lens Resolution Mode: Shows the selected lens combination mode.
  • Voice Recording Sign: Icon indicates ON or OFF.
  • WiFi: Icons indicate OFF, ON but not connected, ON and connected.
  • Recording Sign: Red dot means recording. Time display (e.g., 00:01:00) is recording time. White font (00:00:00) means not recording.

3.3 Key Function Board on Main Page

Each button has two functions: a short press (left function) and a long press (about 3 seconds, right function).

  • Power Button:
    - Short press: Open/Close the screen.
    - Long press: Power ON/OFF.
  • M Button:
    - Short press: Enter the Menu page (stops recording).
    - Long press: Enter the Playback page (stops recording).
  • Up Button:
    - Short press: Trigger emergency lock (locks current 20-second video clip).
    - Long press: Enter the Playback page.
  • Down Button:
    - Short press: Switching Lens Screen.
    - Long press: Take a photo.
  • OK Button:
    - Short press: Start/Stop Recording.
    - Long press: Turn WiFi ON/OFF.

3.4 WiFi Function

3.4.1 WiFi Function Instructions

  1. Scan the QR code on your mobile phone to download the Viidure APP or search for "viidure" in your app store.
  2. WiFi Name (SSID): Tiesfong_Cam_XXXX (WIFI Serial Number)
  3. WiFi Password (PWD): 12345678 (Initial Unified Password)

3.4.2 WiFi Connection Steps

  1. Turn on the WiFi function of the dash cam (long press OK button for 3 seconds on Recording page).
  2. On your phone, go to WLAN settings and find "Tiesfong_Cam_XXXX".
  3. Enter the password to connect to the dash cam's WiFi.
  4. Open the 'Viidure' APP and connect to the WiFi account.

Note: It is not recommended to modify the WiFi Name. If you need to modify the WiFi password, connect to the APP and change it in settings. If the SSID is not found, restart WLAN on your phone and swipe the 'NETWORKS' list.

Screenshot of the Viidure App interface showing WiFi connection and app features.
Figure 3.2: Viidure App Interface

3.5 Menu Page Details

From the main page, short press the M button to enter the Menu page.

Menu page of the dash cam showing options like Video playback, Settings, Quick Set, and Format.
Figure 3.3: Menu Page

Function Board on the Setting Page:

On the setting page, each button has a function only on a short press.

  • Short press Home icon: Back to Main page.
  • Short press Left/Right arrow icons: Switch to previous/next selection.
  • Short press OK icon: Confirm function.

3.6 Video Playback Page

From the Menu page, select "Video playback" to view recorded files.

Video playback screen showing recorded files, recording time, and camera ID.
Figure 3.4: Video Playback Interface

Function Explanation:

  • Lens & Select / Switch Lens: Select and switch lenses; the display will change to the corresponding lens.
  • Camera ID: F (Front Cam) / I (Inside Left+Right Cam) / B (Rear Cam).
  • Video Number: Videos are counted from 0.
  • Video (Normal) File: Videos recorded when the car is started. These are automatically overwritten in a cyclical loop.
  • Parking File: Videos recorded when the car is completely turned off. These are automatically overwritten in a cyclical loop.
  • Lock File: Videos triggered by emergency lockout or manually protected. These are NOT automatically overwritten and must be deleted manually or by formatting the card.
  • Photo File: Photos captured by the photo function. These are automatically overwritten in a cyclical loop.

Playing a Video:

  1. On the playback page, use the Up/Down buttons to switch between lens folders.
  2. Use the Up/Down buttons to switch between file types (Normal, Parking, Lock, Photo).
  3. Press OK to enter the folder.
  4. Use the Up/Down buttons to select the video you want to check.
  5. Press OK to play the selected video.
  6. While a video is selected, long press the M button to set protection or delete the current video.

3.7 Settings Page

The settings page contains 'Video Settings' and 'System Settings'.

Settings page of the dash cam showing various configuration options.
Figure 3.5: Settings Page

Video Settings Module:

  • Recording Mode: 2K+3*1080P (default) / 4K+1080P / 4K. Select based on your needs.
  • IR LED: Off / On / Auto (default & recommend). Auto mode opens in dark scenes, closes in bright scenes.
  • Loop Time: 1 min / 2 min / 3 min (default). Recorder cuts video into segments of this duration.
  • Mic: Off / On (default). Controls voice recording.
  • G-sensor: Off / Low (default & recommend) / Medium / High. Triggers emergency lock on vibration.
  • Video Watermarks: Date+time / Latitude and longitude / License plate / Speed. Tick to display on recorded videos (all ticked by default).
  • Light Frequency: 50Hz / 60Hz (default). Screen update frequency.

System Settings Module:

  • Format: YES / NO. Erases all files on the Micro SD card.
  • WiFi: Off / On (default). Turns WiFi on/off.
  • Screen Save: Off (default) / 30 seconds / 60 seconds / Off-screen recording. Controls when the screen turns off.
  • Language: Select your preferred language.
  • Device Tones: Key Beep / Voice Prompt / Power on/off sound. Tick to enable.
  • Time Settings: Year / Month / Day / Hour / Minutes / Seconds. Set local time.
  • License Plate: Off / On. If On, you can enter your license plate number.
  • GPS: Off / On (default). Enables GPS tracking.
  • GPS Status: Red/Orange icon means not connected or no signal. Green icon means connected or has signal.
  • Speed Unit: km/h (default) / mph.
  • Speed Calibration: -10km/h to 10km/h (default 0km/h). Fine-tunes speed display.
  • Timezone: GMT-12:00 to GMT+12:00 (default GMT-5:00). Set based on your country. Important for correct time display.
  • Daylight Saving Time: Off (default) / On.
  • Reset: YES / NO. Restores dash cam to initial default state.
  • Version: Displays Version INFO / WiFi Account / WiFi Password / APP Name / APP QR Code.

3.8 Quick Setup

This page allows quick settings for Resolution, IR LED, Mic, and Reset without navigating through the full settings menu.

Quick Setup menu showing Resolution, IR LED, Mic, and Reset options.
Figure 3.6: Quick Setup Menu
  • On the selected function, a blue box appears.
  • Press the Up/Down buttons to switch between functions.
  • Press OK to enter and set them.

3.9 GPS Tracking

3.9.1 GPS Data Display

  • After successful GPS positioning, speed will be displayed in the lower right corner of the dash cam's recording page.
  • Speed, Latitude & Longitude will display in the lower left corner of the recorded video.
Screenshot of dash cam footage with GPS data overlay, showing coordinates, speed, and time.
Figure 3.7: GPS Data Display

3.9.2 Check GPS Data on APP

  1. For Android: Download the offline map first (More > APP Settings > Offline Map).
  2. Select the video you want to download.
  3. After downloading, click on the local album in the APP.

Note: After downloading the video to the local album, to view the track, disconnect your phone from the dash cam and keep your phone connected to the Internet to read the map packet.

3.9.3 Check GPS Data on Computer

  1. Remove the Micro SD card from the dash cam and insert it into a Card Reader.
  2. Connect the Card Reader to your computer's USB port and open the removable disk.
  3. In the root folder of the memory card, find the "GXPlayer" software.
  4. Set up the software the first time you use it. Press the Settings button (upper right corner) to personalize content settings.

Note: Stop playing the video before changing map settings in the software.

3.10 Radar Parking Monitor

The dash cam features a built-in 360° sensor radar with dual radar modules, capable of sensing objects 1m to 1.5m around the car.

Diagram illustrating the 360-degree radar parking monitor with proximity trigger.
Figure 3.8: Built-in 360° Radar Parking Monitor

3.10.1 Low-Vol Protection Control (P7 Hardwire Kit)

The P7 Hardwire Kit includes settable gears for low-voltage protection: 11.8V / 12.0V / 12.2V. The general recommended setting is 11.8V.

Diagram of the P7 Hardwire Kit showing low-voltage protection settings and smart tip light.
Figure 3.9: Low-Voltage Protection
  • If the car battery voltage drops below the set value, the power supply will automatically cut off to protect the battery.
  • Smart Tip Light: Displays the car's voltage status. Green light: battery voltage is safe. Red light: battery voltage is low (low-voltage protection triggered).

3.10.2 Radar Working Status

  • Radar Working Light: Indicates if the radar is active. When ACC is disconnected and the radar switch is ON (1 or 2), the radar working light is red.
  • Radar Sensor Light: Indicates if the radar senses moving objects. Red light: moving objects detected. No light: no moving objects.

3.10.3 Radar Sensor Surface

  • Sensor Surface-1 (Front): Senses objects in front of the car (1m non-adjustable distance, 120° horizontal sensing range).
  • Sensor Surface-2 (Inside): Senses objects on the left/right/rear sides of the car. The radar switch gear (1 or 2) adjusts the sensing distance (120° horizontal sensing range).

3.10.4 Radar Switch

  • 0 (OFF): Radar is off, no parking monitoring.
  • 1 (ON/Weak): Radar is on, weak parking monitor mode. Sensing range: 0-1 meters (0-3.3 ft).
  • 2 (ON/Strong): Radar is on, strong parking monitor mode. Sensing range: 0-1.5 meters (0-5 ft).

When the car engine is fully started, the radar light will not be red, and the dash cam will operate normally. When the car engine is fully off, if the radar switch is ON (1 or 2), the radar working light will be red, indicating active radar parking monitoring.

3.10.5 Radar Working Mode

  • When a moving object is detected, the dash cam turns on and records immediately.
  • Recording continues for 90 seconds if movement persists.
  • If no movement is detected for 90 seconds, it enters standby for 10 seconds (no movement detected during this time).
  • After 10 seconds of standby, if no movement is detected, it continues standby. If movement is detected, it repeats the recording cycle.

4. Maintenance

  • Regular Checks: Examine and verify the dash cam and memory card at least every 3 months to ensure proper video reception and recording.
  • Memory Card Formatting: Format the micro SD card once a month to maximize its lifetime.
  • Battery Health: Regularly check the car's battery health status, especially if using parking monitoring features.
  • Cleaning: When cleaning the car, stop using or remove the dash cam.

5. Troubleshooting (FAQ)

Q1: Can I use a mobile power supply to connect the hardwire kit?

A1: No, external power supplies are not recommended. The radar relies on the ignition ACC signal. Insufficient voltage can cause instability. Mobile power quality cannot be guaranteed, posing risks.

Q2: Can I use my own Type-C power cord or the car's USB port?

A2: Not recommended. The logger requires 5V 2.5A. Many car USB ports only provide 2.1A, which may not be enough for stable operation. Use the cigarette lighter car charger port or the fuse box connector, or the standard 5V 2.5A power cables provided.

Q3: Is it normal for the dash cam to get hot?

A3: Yes, multi-lens dash cams consume significant power and dissipate heat, which is normal. The material is flame-retardant, and there's no built-in rechargeable battery to prevent combustion. It's resistant to -20°C to 65°C. If it exceeds normal operating temperature, it will automatically power off. If the screen temperature feels high, enable 'Off-screen recording' in 'System Settings'.

Q4: Why are the date and time incorrect?

A4: This is usually due to incorrect settings. The default time is GMT-5:00. Follow these steps:

  1. Go to 'Setting' page, find 'Time Zone' and set it correctly for your country.
  2. Turn on the GPS function.
  3. Turn on WiFi and connect to the APP.
After these steps, the date and time should update and save automatically.

Q5: Why are videos 1/2/3 minute segments? Can I record as a whole video?

A5: Videos are saved in segments for better preservation and loop recording. When the memory card is full, the oldest segments are automatically deleted. This allows for easier viewing of specific events.

Q6: The Left/Right Cam sometimes flashes red. Is this normal?

A6: This can occur due to devices with face recognition technology nearby. To verify:

  1. Lock your phone screen and don't point it at your face; re-observe the Left/Right Cam.
  2. Cover any face recognition device in your car with your hand; re-observe the Left/Right Cam.
You can also check the official YouTube channel for related videos.

Q7: Why are only a few seconds of video clips saved?

A7: This happens when the locked folder is full, preventing normal recording, or the memory card is damaged. Follow these steps:

  1. Go to the Playback page, find the 'Event' folder, and check for many videos.
  2. Save any useful videos.
  3. Clean up useless videos or format the entire memory card.
  4. After formatting, record for 5-10 minutes and check if video duration is normal (3 minutes).
  5. If formatting fails, replace the memory card.

Q8: Why does the Left/Right Cam video have color difference or turn purple?

A8: The Left/Right Cam has four infrared night vision lights and a built-in red filter for night vision, causing some red color difference. A special night vision filter enhances night vision. This color aberration does not affect video clarity.

Q9: Front/Rear Cam are normal, but Left/Right Cam are black and white. What should I do?

A9: This is a setup issue. If IR LED is set to 'ON', Left/Right Cam will appear black and white regardless of ambient light. Set the IR LED option to 'Auto' in the 'Setting' page.

Q10: WiFi connects to phone but not Viidure APP. What should I do?

A10:

  1. Close the Viidure APP.
  2. Go to phone settings, WLAN function.
  3. Find the dash cam's WiFi, click the blue icon, and select 'Forget this network'.
  4. Turn off dash cam, wait 10 seconds, then turn it back on and turn on WiFi.
  5. Rediscover the dash cam's WiFi in your phone's WLAN and link it.
  6. Reopen the Viidure app.
If issues persist, uninstall and reinstall the Viidure APP.

Q11: Dash cam's WiFi is on, but phone can't find/connect. What should I do?

A11: Your phone's WLAN signal isn't retrieving the dash cam's WiFi. Follow these steps:

  1. Go to phone 'Settings', find WLAN, and turn it off.
  2. Go back to 'Settings' and turn on Airplane Mode.
  3. Turn the dash cam OFF and back ON, then turn its WiFi function back ON.
  4. Re-enter WLAN function and turn it on; your phone should automatically search for the dash cam's WiFi.

Q12: WiFi is not opening or opening abnormally in dash cam. What should I do?

A12: This indicates a stuck program. Follow these steps:

  1. Go to the Setting page, find "Reset", click OK, and select YES.
  2. Wait for the dash cam to reboot, then try turning on WiFi again.
If it still doesn't work after resetting, contact support with your order number, 'Version Info' (Page 18), and the unique SN barcode on the dash cam's bottom for an upgrade software.

Q13: Dash cam reboots/malfunctions on car start. What should I do?

A13: Perform a simple troubleshooting test:

  1. Remove all power cables (power and rear cam) from the dash cam.
  2. Remove the memory card.
  3. Re-energize the dash cam using the cigarette lighter car charger cable.
Then provide support with your order number, a recorded troubleshooting video, 'Version Info' (Page 18), and the unique SN barcode.

Q14: How to judge working status if recorder is set to Off-screen recording?

A14: Observe the working light on the right side of the screen. Always on blue: recorder is on but not recording. Blinking blue: recorder is on and recording.

Q15: Dash cam works when car is on, but radar light doesn't come on after car is off, and recorder doesn't work. Is the hardwire kit broken?

A15: Your radar and P7 hardwire kit are likely not broken. The dash cam gets power from the car battery via the fuse box. If the hardwire kit were broken, it wouldn't power on at all. The problem is likely that the yellow BAT+ wire is connected to a power connector that does not supply constant power. Solutions:

  1. After the car is off for >30 min, re-check if the connector for the yellow wire in the fuse box is a normally charged connector.
  2. Re-test and replace the yellow wire with a new one (after car is off for >30 min).
  3. Set low voltage protection to 11.8V.

Q16: Dash cam worked fine, now car is off, radar switch is ON, but radar working light is not red, and dash cam doesn't work.

A16: This is likely due to low voltage protection. Remember: parking duration, low voltage protection setting, and the color of the P7 hardwire kit light (Page 38). Steps:

  1. Power on your car for >30 min, then check if the dash cam powers on.
  2. If it works, turn off the car, set low voltage protection to 11.8V, and check if the radar working light turns red.

Q17: Dash cam works when car is on, but after car is off, radar working light doesn't come on, and dash cam keeps recording. Is the hardwire kit broken?

A17: Your radar and P7 hardwire kit are likely not broken. The problem is that the red wire of the hardwire kit is connected to an ACC interface that is still powered after the car is turned off. You need to connect the red wire to a true ACC interface (one that loses power when the car is off) (Page 28).

Q18: After car is off, radar working light is red, but recorder keeps recording without interval.

A18: This is usually due to frequent triggering by moving objects or interference from items in the same frequency band. Drive to an empty parking environment, turn off the car, lock it, and leave the radar alone for a period to see if it works properly.

6. Specifications

Detailed specifications table for the TiESFONG A99UB Dash Cam.
Figure 6.1: Product Specifications
CategoryDescription
Brand NameTiESFONG
ModelA99UB
Chipset ManufacturerMSTAR 88Series
Image SensorGalaxy Core GC4653+GC2053
Pixels1200Mega
Camera Resolution2560x1440 (2K)
ApertureF1.6 (Front Cam) + F1.8 (Other Cam)
View Angle4*150°
Number Of Lenses4
Rear CameraYes (Optional S20U - Non-Waterproof)
Video CodeH.265
Video FormatTS, MP4
Max External Memory256G (Supports 64-256G TF Micro SD Card)
Memory Card Required Reading SpeedClass 10
Display Size3.16inch IPS HD Screen
Screen Ratio16:9
Built-in ScreenYes
Touch ScreenNo
OSD LanguageChinese (Simplified), Chinese (Traditional), English, French, German, Italian, Japanese, Korean, Russian, Spanish
Power SourceCorded Electric
Input/OutputTYPE-C
Input5V 2.5A
Supported Car Voltage12V-24V
BatteryNone (Built-in RCT button battery, non-rechargeable)
Working Temperature-20℃~65℃ (-4℉~149℉)
Special FeaturesG-Sensor, Motion Detection, Radar Detector, Real Time Surveillance, Automatic White Balance, Wide Dynamic Range, WiFi Function, Bluetooth, Parking Monitor, Speed and Coordinates Recording, 3D DNR, External GPS, Loop-Cycle Recording, Audio Recorded, NightShot Function
APP CompatibilityYES (Viidure)
CertificationCE, FCC, RoHS

7. User Tips

  • Memory Card Management: Regularly back up important videos from the 'Event' folder to a computer, as these files are protected and can fill up the card, preventing new recordings. Consider formatting your memory card monthly to maintain optimal performance.
  • Power Source for Stability: For stable operation, it is recommended to power the dash cam using the cigarette lighter car charger port or the fuse box connector, rather than the car's USB port, which may not provide sufficient current.
  • Troubleshooting Documentation: If you encounter issues, record the troubleshooting process with a video. This can help support staff diagnose problems more effectively and save you time.
  • Extreme Weather Parking: In extreme weather conditions (very high or low temperatures), especially if parking outdoors for extended periods, it is advisable to turn off the radar switch to suspend parking monitoring and protect the device.

8. Warranty and Support

TiESFONG is committed to providing high-quality products and excellent customer service.

  • After-Sales Service: If you have any questions or encounter problems with your product, please feel free to contact us. Inquiries are usually answered within 12-24 hours.
  • Contact Email: tiesfong@gmail.com
  • Online Resources: For additional support and video tutorials, visit our official YouTube channel: youtube.com/@TIESFONG
  • Feedback: We welcome your constructive feedback and suggestions to help us improve our products and services.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.