AnyTone 5888UV

Contents

Anytone 5888UV Dual Band FM Transceiver User Manual

Model: 5888UV | Brand: AnyTone

1. Introduction

Thank you for choosing the Anytone 5888UV mobile transceiver. This ruggedly-built, high-quality Dual Band FM transceiver is designed for drivers and pursues a philosophy of innovation and practicality. It provides 50 Watts of power output on the VHF band and 40 Watts on the UHF band.

The Anytone 5888UV features four independent receiving bands (UU, UV, VU, VV) for dual receive and dual output, along with reception for AM/FM signals in air band, marine band, and PMR. It can also receive FM/TV radio and analogue TV signals (optional). The transceiver includes 758 memory channels, full duplex operation with independent volume and squelch controls, compander, built-in CTCSS/DCS, DTMF, 5TONE, 2TONE signaling, and a detachable front panel for flexible installation.

1.1. Safety Precautions

Please observe the following precautions to prevent fire, personal injury, or transceiver damage:

  • Do not attempt to configure your transceiver while driving; it is dangerous.
  • This transceiver is designed for a 13.8V DC power supply. Do not use a 24V battery to power on the transceiver.
  • Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces.
  • Keep it away from interferential devices (such as TV, generators, etc.).
  • Do not expose the transceiver to long periods of direct sunlight or place it close to heating appliances.
  • If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact an Anytone service station or your dealer.
  • Do not transmit with high output power for extended periods; the transceiver may overheat.

1.2. Electromagnetic Interference/Compatibility

During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. Do not operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

1.3. Occupational/Controlled Use

This product is used in situations where users are exposed to RF as a consequence of their employment, provided those users are fully aware of the potential RF hazards and can exercise control over their exposure. This transceiver is NOT ATEX approved and NOT intended for use in hazardous explosive atmospheres.

2. Setup

2.1. Supplied Accessories

After carefully unpacking the transceiver, identify the items listed below. It is recommended to keep the box and packaging for future use.

  • 1x 5888UV Radio Body
  • 1x Speaker Mic (with DTMF keyboard)
  • 1x Mobile Mounting Bracket (QMB-01)
  • 1x DC Power Cable with Fuse Holder (QPL-01)
  • 1x Hardware Kit for Bracket (screws and S-washer)
  • 1x Spare Fuses (QF-01)
  • 1x User Manual
  • 1x Hook for Speaker Mic
  • 1x USB Programming Cable (Optional)
Standard accessories included with the Anytone 5888UV mobile radio.
Figure 2.1: Standard accessories included with the Anytone 5888UV mobile radio.

2.2. Initial Installation

2.2.1. Mobile Installation

Select a safe, convenient location inside your vehicle that minimizes danger to passengers and yourself. Install the unit so that knees or legs will not strike it during sudden braking. Choose a well-ventilated location shielded from direct sunlight.

  1. Install the mounting bracket in the vehicle using the supplied self-tapping screws (4pcs) and flat washers (4pcs).
  2. Position the transceiver, then insert and tighten the supplied hexagon SEMS screws. Double-check that all screws are tightened to prevent vehicle vibration from loosening the bracket or transceiver.
Anytone 5888UV Mobile Radio with microphone, front view.
Figure 2.2: Anytone 5888UV Mobile Radio with microphone, front view.

2.2.2. Fixed Station Operation

For fixed station operation, a separate 13.8V DC power supply (not included) is required. The recommended current capacity of your power supply is 12A.

2.3. DC Power Cable Connection

  1. Route the DC power cable directly to the vehicle's battery terminals using the shortest path from the transceiver. Avoid using the cigarette lighter socket as it may introduce unacceptable voltage drop.
  2. After installing the cable, use heat-resistant tape to tie it together with the fuse box. Reinforce the entire cable.
  3. To avoid short circuits, cut down the connection with the negative (-) of the battery first, then connect with the radio.
  4. Confirm correct polarity: red connects to the positive (+) terminal and black connects to the negative (-) terminal.
  5. Use the full length of the cable without cutting off excess. Do not remove the fuse holders from the cable.
  6. Reconnect any wiring removed from the negative terminal.
  7. Connect the DC power cable to the transceiver's power supply connector. Press firmly until the locking tab clicks.

Note: Before connecting the DC power to the transceiver, ensure both the transceiver and the DC power supply are OFF. Do not plug the DC power supply into an AC outlet until all connections are made.

2.4. Antenna Connection

Before operating, install an efficient, well-tuned 50Ω impedance antenna and low-loss coaxial feed-line. Proper antenna installation is crucial for optimal performance and to avoid interference with other electronic equipment.

Warning: Transmitting without first connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the transceiver before transmitting. All fixed stations should be equipped with a lightning arrester to reduce the risk of fire, electric shock, and transceiver damage.

2.5. Accessories Connections

2.5.1. External Speaker

If you plan to use an external speaker, choose one with an impedance of 8Ω. The external speaker jack accepts a 3.5mm (1/8") mono (2-conductor) plug.

2.5.2. Microphone

For voice communications, connect a microphone equipped with an 8-pin modular plug into the modular socket on the front of the main unit. Press firmly on the plug until the locking tab clicks. Attach the supplied microphone hanger in an appropriate location using the screws included in the screw set.

2.6. PC Connecting

To utilize the QPS5888UV_S1 software for programming, connect the transceiver to your PC using an optional programming cable PC50 (via Data socket). The software can be downloaded from www.qxdz.cn.

Note: Install the USB Cable Driver Programme by running "QPS5888UV_S1 setup.exe" and following the instructions. Ensure the transceiver is connected to the PC before starting the software. Do not switch on/off the power supply of the transceiver when it is connected to the computer to avoid read/write errors.

3. Operating Instructions

3.1. Front Panel Controls

Front panel layout of the Anytone 5888UV Dual Band FM Transceiver.
Figure 3.1: Front panel layout of the Anytone 5888UV Dual Band FM Transceiver.
Table 3.1: Front Panel Controls Overview
Key/Knob Function
Left Dial KnobRotate to choose frequency/channel. Press to set the left band as "Main Band"; In VFO mode, press to choose the frequency band; In function setup as confirm key; in scan mode, rotate to change scan direction.
Right Dial KnobRotate to choose frequency/channel. Press to set the right band as "Main Band"; In VFO mode, press to choose the frequency band; In function setup as confirm key; in scan mode, rotate to change scan direction.
Left Volume KnobAdjust left band volume level.
Right Volume KnobAdjust right band volume level.
PWRPress to power On/Off the transceiver.
TV/SQLIn standby, press to turn On/Off TV function. Hold to cancel squelch.
SETIn standby, press to enter function menu.
LOWIn standby, press to change H/L power. Long press to turn On/Off Frequency Reverse Function.
V/MIn standby, press to switch between channel mode and VFO mode. Long press to set Wide/Narrow band.
HMIn standby, press to switch between HOME channel and normal channel. Long press to enter dual watch of VFO channel and current channel.
SCNIn standby, press to start channel or frequency scan. In channel mode, hold to set current channel scan skip.
DISPLAYFor display of channel, frequency and function setup.

3.2. Rear Panel Controls

Rear panel layout of the Anytone 5888UV Dual Band FM Transceiver.
Figure 3.2: Rear panel layout of the Anytone 5888UV Dual Band FM Transceiver.
Table 3.2: Rear Panel Controls Overview
Key Function
Ext. Power JackTerminal for connecting optional cable QCC01 for use with ignition key On/Off function. The radio will auto power on when car is driving. The radio will auto power off when car stops.
Ext. Speaker TerminalTerminal for optional external speaker SP02.
TV/AV portConnect to television TV/AV port. (Optional)
Heat-sink fanRuns Automatically when radio temperature rises.
Antenna ConnectorConnect a 50 Ω antenna.

3.3. Microphone Controls

Table 3.3: Microphone Controls Overview
Key Function
UPIncrease frequency, channel number or setting value.
DOWNDecrease frequency, channel number or setting value.
PTTPress the PTT (Push-To-Talk) key to transmit.
Number KeypadInput VFO frequency or DTMF dial out etc.
A/B bandChoose left band or right band as Main band.
Band indicatorThe indicator light on for Main band.
TX/RX indicatorLight green while receiving, Light red while transmitting.
MICSpeak here during transmission.
SpeakerWhen the speaker in the base is shut, you can hear the calling by this speaker.
Lock UP/downWhen this key is in up position, it is unlock UP/DOWN key; when this key is in down position, UP/DOWN key will be locked.

3.4. Basic Operations

3.4.1. Switching Power On/Off

  • Power On: Press the PWR key to switch the transceiver ON. The LCD will display "WELCOME ANYTONE", then the current frequency or channel.
  • Power Off: Press the PWR key for over 0.5 seconds to switch the transceiver OFF.

3.4.2. Adjusting Volume

Rotate the [VOLUME] knob of the selected band clockwise to increase the volume, counterclockwise to decrease the volume.

3.4.3. Switching Between VFO and Channel Mode

In standby, press the V/M key to switch between Frequency and Channel mode. When in channel mode, the LCD will display the current channel.

3.4.4. Adjusting Frequency

In VFO mode, turn the selector knob clockwise to increase frequency; counterclockwise to decrease frequency. Each step will increase or decrease frequency by one step. To adjust the Main band frequency, press the corresponding selector knob; the left side of the decimal point will flash. In this status, turning the selector knob will increase or decrease frequency quickly by 1MHz step.

3.4.5. Adjusting Channel

In channel mode, you can adjust the channel directly by the channel knob. Turn clockwise to increase one channel; turn counterclockwise to decrease one channel. To adjust the Main band channel, press the corresponding selector knob; the channel number flashes in this situation, the channel number will increase 10 channels by each gear of selector knob. Press the microphone [UP/DOWN] key to adjust the channel.

3.5. Shortcut Operations

3.5.1. Squelch Level Setup

In standby, press and hold the TV/SQL key, meanwhile switch the selector knob to adjust the squelch level of the Main band. There are 1-20 squelch levels available. "OFF" turns off squelch. The squelch level must be set up separately for the right and left bands.

3.5.2. High/Mid/Low Power Switch

In standby, repeat pressing the LOW key to choose power levels. When the LCD displays HIGH, the power for the current channel is high. When MID1, it's middle 1. When MID2, it's middle 2. When LOW, it's low. Output power for each level: VHF (50W, 20W, 10W, 5W), UHF (40W, 25W, 10W, 5W).

3.5.3. Dual Watch

In standby, hold the HM key for over 0.5 seconds to enter Dual Watch mode. The radio will scan the channel every 5 seconds. When a matching signal is received, it pauses scanning until the signaling disappears. Repeat the operation to exit Dual Watch.

Diagram showing Dual Receive, Dual Watch functionality with two handheld radios and the mobile radio.
Figure 3.3: Dual Receive, Dual Watch functionality.

3.6. General Settings (Menu Functions)

Access general settings by pressing the SET key. Use the Main band selector knob to navigate through menu items and adjust values.

  • APO (Automatic Power Off): Activates automatic power off after a preset timer.
  • Automatic Offset: Transceiver automatically transmits with RX frequency ± offset frequency.
  • Frequency Channel Step Setup: Sets frequency step size for VFO mode.
  • VFO Band Lockout: Restricts scanning or input within the current VFO frequency band.
  • Beep Function: Turns the beep sound on or off.
  • CPU Clock Frequency Change: Reduces interference from CPU clock harmonics.
  • 2TONE/5TONE Encode Select: Configures 2TONE/5TONE encoding.
  • CTCSS/DCS Encode/Decode Setup: Configures CTCSS/DCS signaling for filtering unwanted signals.
  • Sub Band Display Setup: Configures sub band display options.
  • DTMF Encode Pre-Loading Time: Sets the pre-loading time for DTMF encoding.
  • DTMF Encode Transmitting Time: Sets the transmitting time for DTMF encoding.
  • Compander: Decreases background noise and enhances audio clarity, especially in long-range communication.
  • Scrambler: Offers confidential communication by scrambling audio. Other radios on the same frequency will receive only disordered noises.
  • Tone Burst (Pilot Frequency): Used to start a dormant repeater with a certain intensity pilot frequency.
  • Keypad Mode Setup: Configures keypad functionality.
  • TX OFF (PTT Lockout): Prevents accidental transmission.
  • Squelch Level Setup: Adjusts the squelch threshold.
  • Frequency Reverse: Swaps TX and RX frequencies.
  • Sub Band Mute Setup: Mutes the sub band during main band RX or TX.
  • Editing Channel Name: Allows assigning names to channels.
  • Channel Function Auto Storage Setup: Stores the latest setup for each channel.
  • Microphone PA, PB, PC, PD Key Setup: Programs functions for microphone keys.
  • RF Squelch Level Setup: Adjusts squelch based on signal strength.
  • OFFSET Direction Setup: Configures offset direction for repeater use.
  • Scan Dwell Time Setup: Sets the time the scanner pauses on a busy channel.
  • Priority Channel Scan: Scans a priority channel.
  • Offset Frequency Setup: Configures offset frequency.
  • Display Mode Setup: Changes the display mode (channel number, frequency, name).
  • Busy Channel Lockout: Prevents transmission on a busy channel.
  • Radio's DTMF SELF ID ENQUIRY: Displays the radio's DTMF self ID.
  • 5TONE SELF ID ENQUIR: Displays the radio's 5TONE self ID.
  • TOT (Time-out timer): Limits continuous transmitting time.
  • VFO Frequency Linkage: Links VFO frequency changes across bands.
  • Wide/Narrow band: Selects bandwidth (25KHz Wide, 20KHz Middle, 12.5KHz Narrow).
  • Cross Band Repeat: Enables cross band repeater function.
  • LCD backlight: Adjusts LCD backlight brightness.
  • Keypad backlight brightness: Adjusts keypad backlight brightness.
  • Calling Record: Views calling records.
  • AM Function: Enables AM function.
  • Automatic AM function: Automatically enables AM function when VHF frequency is under 136MHz.
  • VHF External speaker port: Configures external speaker output.
  • BEEP Volume control: Adjusts beep volume.
  • Talk Around: Allows direct communication without a repeater.
  • Microphone speaker: Configures microphone speaker.
  • Password Function: Sets a password for radio access.
Video 3.1: Unboxing and demonstration of basic functions and menu navigation on the Anytone 5888UV.

4. Maintenance

4.1. Replacing Fuses

If a fuse blows, determine the cause and correct the problem. Replace the fuse with one of the specified type and rating (Transceiver: 15A, Supplied Accessory DC power cable: 20A). If newly installed fuses continue to blow, disconnect the power cable and contact your authorized dealer or service center.

Note: Only use fuses of the specified type and rating. Using incorrect fuses could damage the transceiver. If the transceiver is used for a long period when the vehicle battery is not fully charged, or when the engine is OFF, the battery may become discharged. Avoid using the transceiver in these conditions.

4.2. Cable Clone

This feature copies programmed data and parameters from a master unit to slave units. To perform a clone:

  1. Use an optional CP52 cloning cable to connect the data jacks on both master and slave units.
  2. Press and hold the right band LOW key to power on, then hold this key until the LCD displays "CLONE".
  3. Hold the Main band TV/SQL key. Both units will display "CLONE XX" (XX is the data amount). When "CLONE" displays again, the slave unit will repower on, indicating the clone is complete.

Note: If data is not successfully transmitted, turn off both units, ensure the cable connection is correct, and repeat the entire operation.

4.3. Resume Factory Default

If your radio is malfunctioning due to incorrect operation or setup, you can restore all settings and channels to factory default. Hold the right band SCN key while powering on the radio; all channel and function setups will revert to factory default.

4.4. Programming Software Installation

To install the USB Cable Driver Programme, double-click "QPS5888UV_S1 setup.exe" and follow the installation instructions. Connect the optional PC50 USB Programming cable to a USB port on your PC and the transceiver. Select the correct COM Port in the software to begin programming.

Note: Do not switch on or off the power supply of the transceiver when it is connected to the computer, as this may prevent the transceiver from reading or writing frequencies. If this occurs, turn off the programming software, pull out the USB cable, then reinsert it and re-select the COM Port.

5. Troubleshooting

Table 5.1: Troubleshooting Guide
Problem Possible Causes and Potential Solutions
Power is on, nothing appears on Display.Polarities of power connection are reversed. Connect red lead to plus terminal and black lead to minus terminal of DC power supply.
Fuse is blown.Check and solve problem resulting in blown fuse and replace fuse with new fuse.
Display is too dim.Adjust the Dimmer to a higher level.
No sound comes from speaker.Squelch is muted. Decrease squelch level. Tone or CTCSS/DCS squelch is active. Turn CTCSS or DCS squelch off.
Key and Dial do not function.Key-lock function is activated. Cancel Key-lock function.
Rotating Dial will not change memory channel.Transceiver is in CALL mode or VFO mode.
PTT key is pressed but transmission does not occur.Microphone connection is poor. Connect microphone properly. Antenna connection is poor. Connect antenna properly.

6. Specifications

Detailed specifications table for the Anytone 5888UV Dual Band FM Transceiver.
Figure 6.1: Detailed specifications for the Anytone 5888UV.
Table 6.1: General Specifications
Category Description
Frequency Range (TX)VHF 136-174MHz & UHF 400-490MHz
Frequency Range (RX)Air Band: 108-180MHz (AM/FM), VHF: 136-174MHz, VHF2: 220-260MHz (FM), UHF2: 350-399.995MHz (FM), UHF: 400-523MHz (FM)
Number of Channels758 channels
Channel Spacing25KHz (Wide Band), 20KHz (Middle Band), 12.5KHz (Narrow Band)
Phase-locked Step2.5KHz, 5KHz, 6.25KHz, 10KHz, 12.5KHz, 15KHz, 20KHz, 25KHz, 30KHz, 50KHz
Operating Voltage13.8V DC ±15%, negative ground
SquelchCarrier/CTCSS/DCS/5 Tone/2Tone/DTMF
Frequency Stability±2.5ppm
Operating Temperature-14°F to +140°F (-10°C to +60°C)
Dimensions (W*H*D)139(W)*40(H)*212(D)mm
WeightAbout 1.14kg

6.1. Receiver (ETSI EN 301 783)

Parameter Wide Band Narrow Band
Sensitivity (12dB SINAD)≤0.25μV≤0.35μV
Adjacent Channel Selectivity≥70dB≥60dB
Audio Response+1~-3dB(0.3-3KHz)+1~-3dB(0.3-2.55KHz)
Hum & Noise≥45dB≥40dB
Audio distortion≤5%
Audio power output>2W@10%

6.2. Transmitter (ETSI EN 301 783)

Parameter Wide Band Narrow Band
Power Output50W/25W/10W/5W (VHF), 40W/25W/10W/5W (UHF)
Modulation16KΦF3E11KΦF3E
Adjacent Channel Power≥70dB≥60dB
Hum & Noise≥40dB≥36dB
Spurious Emission≥70dB≥70dB
Audio Response+1~-3dB(0.3-3KHz)+1~-3dB(0.3-2.55KHz)
Audio Distortion≤5%

All specifications may be modified without prior notice or liability.

7. User Tips

  • When programming the transceiver, always read the factory initial data first before rewriting frequencies or signaling to avoid errors.
  • If you experience issues with front panel buttons not functioning, consider checking for logical or hardware faults, and consult the troubleshooting section or support.
  • For programming, ensure the USB cable driver is correctly installed and the transceiver is connected before starting the software.

8. Warranty and Support

For technical support, service, or warranty inquiries, please contact your authorized Anytone service station or dealer. You can also visit the manufacturer's website at www.anytone.net for more information.

Qixiang Electron Science & Technology Co., Ltd. is committed to providing quality products and support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.