ZHRIVOER 12mm Metal Button Switch

Contents

Ruiwo 12mm Metal Button Switch User Manual

Brand: ZHRIVOER | Model: 12mm Metal Button Switch

1. Introduction

Thank you for choosing the Ruiwo 12mm Metal Button Switch. This manual provides detailed instructions for the safe and effective installation, operation, and maintenance of your new switch. Please read this manual thoroughly before use and retain it for future reference.

These durable metal push button switches are designed for various applications, featuring options for LED illumination, different voltage ratings (3-6V, 12-24V, 220V), and operation types (momentary or latching). They are splash-proof and constructed with a copper nickel-plated shell for longevity.

Four 12mm metal button switches with LED lights in red, blue, orange, and white.
Figure 1: Assortment of Ruiwo 12mm Metal Button Switches with LED.

2. Safety Information

  • Always disconnect power before installing or servicing the switch to prevent electrical shock.
  • Ensure the switch's voltage rating matches your application's power supply.
  • Handle with care to avoid damaging the switch or its components.
  • Installation should be performed by qualified personnel if you are unsure about electrical wiring.
  • The switch is splash-proof, but not fully submersible. Avoid prolonged exposure to water.

3. Specifications

The following table outlines the key specifications for the Ruiwo 12mm Metal Button Switch:

Table of product parameters including product name, diameter, contact form, shell material, operation type, LED color, LED voltage, and wiring type.
Figure 2: Product Parameters.
ParameterDescription
Product NameMetal Push Button Switch
Diameterφ12mm
Contact Form1NO (Normally Open)
Shell MaterialMetal Shell (Copper nickel plated)
Operation TypeMomentary / Latching (Self-locking / Resetting)
LED ColorRed, Yellow, Blue, Green, White
LED Voltage3-6V, 12-24V, 220V (depending on model)
Wiring TypePin Type
MaterialCopper
EU LVD VoltageBelow 50Vac or 75Vdc
CertificationCE

Note: Manual measurements may result in slight errors. The LED colors and voltages are available in various configurations; please ensure you have the correct model for your needs.

High quality LED lights in various colors and voltages.
Figure 3: Available LED Colors and Voltages.
Close-up of a metal button switch showing its copper nickel plated shell.
Figure 4: Copper Nickel Plated Metal Shell.

4. Setup and Installation

The Ruiwo 12mm Metal Button Switch is designed for easy installation. The installation diameter is φ12mm.

4.1. Using Supporting Plugins (Optional)

For simplified installation and to avoid welding, matching sockets (plugins) are available and sold separately. These plugins allow for quick and secure connections.

Button switch connected with a supporting plugin, illustrating easy installation without welding.
Figure 5: Easy Installation with Supporting Plugins.
A single connector (socket) for the button switch.
Figure 6: Optional Connector (Sold Separately).

4.2. Wiring Methods (1NO Contact Form)

The switch features a 1NO (Normally Open) contact form. Below are two common wiring methods for switches with LED lights. Ensure correct polarity for the LED (+ and - terminals).

Wiring Method 1: LED and Load Powered Together

In this configuration, the LED light illuminates only when the switch is pressed and the load is active.

Wiring diagram for 1NO switch where LED and load are powered simultaneously when the switch is pressed.
Figure 7: Wiring Method 1 (LED and Load Powered Together). This diagram shows the positive terminal of the power source connected to one side of the switch's NO contact and the positive terminal of the LED. The other side of the switch's NO contact is connected to the positive terminal of the load. The negative terminals of the LED, load, and power source are all connected together.

Wiring Method 2: LED Always On

This method keeps the LED light illuminated continuously, regardless of the switch's state, indicating power is supplied to the circuit.

Wiring diagram for 1NO switch where the LED is always on, independent of the switch state.
Figure 8: Wiring Method 2 (LED Always On). This diagram shows the LED connected directly across the power source (with appropriate resistor if needed, not shown in diagram but implied for LED operation). The switch's NO contacts are connected in series with the load and the power source, allowing the load to be controlled independently of the LED's illumination.

Important: Always ensure the LED voltage matches the power supply for the LED. An external resistor may be required for certain LED voltages if not integrated into the switch.

5. Operating Instructions

5.1. Momentary Switch

A momentary switch activates the circuit only while the button is being pressed. Once released, the circuit returns to its original state (open).

  • To activate: Press and hold the button.
  • To deactivate: Release the button.

5.2. Latching (Self-locking) Switch

A latching switch maintains its state after being pressed. Pressing it once activates the circuit, and it remains active until pressed again to deactivate it.

  • To activate: Press the button once. The switch will 'lock' into the ON position.
  • To deactivate: Press the button again. The switch will 'unlock' and return to the OFF position.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the switch surface. Avoid abrasive cleaners or solvents that could damage the metal finish or internal components.
  • Inspection: Periodically check the wiring connections to ensure they are secure. Inspect the switch for any signs of physical damage or wear.
  • Environmental Conditions: While splash-proof, avoid exposing the switch to extreme temperatures, corrosive substances, or excessive moisture to prolong its lifespan.

7. Troubleshooting

  • Switch Not Responding:
    - Check all wiring connections for looseness or incorrect placement.
    - Verify that the power supply is active and providing the correct voltage.
    - Ensure the switch's voltage rating matches the circuit's voltage.
  • LED Not Lighting Up:
    - Confirm correct LED polarity (+ and - terminals).
    - Check the LED's voltage requirement against the power supply. An incorrect voltage can prevent illumination or damage the LED.
    - Review the wiring diagram to ensure the LED is correctly integrated into the circuit (e.g., for 'LED always on' vs. 'LED with load').
  • Intermittent Operation:
    - Inspect for loose connections or damaged wires.
    - Ensure the switch is securely mounted and not experiencing physical interference.

8. User Tips

Based on common user experiences and questions:

  • When selecting a switch, pay close attention to the voltage rating (3-6V, 12-24V, 220V) and the operation type (momentary or latching) to ensure it matches your project requirements.
  • Consider purchasing the optional matching connectors/sockets to simplify installation and avoid the need for soldering, especially for multiple switches.
  • For applications requiring constant visual feedback, use Wiring Method 2 to keep the LED illuminated. For power indication only when the circuit is active, use Wiring Method 1.
  • Always double-check wiring against the provided diagrams before applying power to prevent damage to the switch or connected devices.

9. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller directly through the platform where you purchased the product. Provide your order number and a detailed description of the issue for prompt support.

You can also refer to the official user manual (PDF) for additional details: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.