1. Introduction
Thank you for purchasing the Baofeng UV-K6, a dual-band, dual-display, and dual-watch amateur radio. This manual provides detailed instructions to help you get the most out of your device, ensuring secure, instant, and reliable communications. Please read it carefully before use.
Key Features:
- 6-Band Frequency Support:
- FM: 65-108 MHz (RX only)
- AM: 108-136 MHz (Air Frequency Receiving)
- VHF1: 136-174 MHz (TX/RX)
- VHF2: 220-260 MHz (TX/RX)
- UHF1: 400-520 MHz (TX/RX)
- UHF2: 350-390 MHz (RX only)
- 520-600 MHz (RX only)
- Wireless Copy Frequency for easy pairing.
- Type-C USB Charging for convenience.
- 999 Memory Channels.
- DTMF Encoder and Manual Dial.
- VOX (Voice Activated Transmit) function.
- LED Flashlight for emergencies.
- NOAA Weather Stations reception.
- FM Radio receiver (65-108 MHz).
- Stopwatch function.
- Alarm function.
- High or Low Power selectable.
- Programmable Repeater Offset.
- Transmission Time-Out Timer.
- End of transmission tone ("Roger Beep").
- Display illumination programmable via keypad.
- Battery save function.
- Busy channel lockout.
- Ten (10) levels of Squelch adjustment.
- Two (2) pins for Kenwood accessory port.

2. Setup
2.1 Content of the Packaging
Please verify that all items are present in your package. If any item is missing, contact your dealer.
- 1 Radio
- 1 Antenna
- 1 Battery
- 1 Fast desktop charger
- 1 Wall adaptor
- 1 Belt clip
- 1 Lanyard
- 1 User Manual (PDF available for download: User manual (PDF))

2.2 Charging the Battery
The Li-ion battery pack is not charged at the factory; please charge it before first use. For optimal performance, fully charge and discharge the battery two or three times.
2.2.1 Charger Supplied
Use only the specified charger provided by the manufacturer. Using other chargers may cause damage or injury.2.2.2 How to Charge
- Plug the AC adaptor into a wall outlet, then connect its cable to the DC jack on the back of the charger. The indicator light will blink orange, indicating it's ready.
- Place the battery or the radio (with battery installed) into the charger. Ensure good contact between the battery terminals and charging terminals. The indicator light will turn red, signifying charging has begun.
- A full charge typically takes 2-5 hours. The lamp turns green when charging is complete. Remove the battery or radio from the charger.
Note: If the radio is powered on during charging, the indicator lamp may not turn green to show full charge. For optimal battery life, remove the radio from the charger within 6 hours and do not store it connected to the charger.
2.2.3 Using the Type-C USB Charger
The UV-K6 supports Type-C USB charging, offering a convenient way to charge the Li-ion battery pack.
- Ensure your radio is turned OFF.
- Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end to a wall power outlet or a compatible USB power source (e.g., power bank, laptop).
- An empty battery will be fully charged in approximately 4 hours.
- The battery meter on the LCD will indicate charging progress.

Video demonstrating the physical features and charging options of the Baofeng UV-K6 walkie talkie, including Type-C charging and accessory ports.
2.3 Installation of Accessories
2.3.1 Installing/Removing the Antenna
- Screw the antenna clockwise onto the connector on top of the radio until it is firm.
- To remove, unscrew counter-clockwise.
2.3.2 Installing the Battery Pack
- Ensure the radio is OFF by turning the power/volume knob fully counter-clockwise.
- Align the battery pack in parallel with the radio body, with its lower edge about 1-2cm below the radio's edge.
- Once aligned with the guide-rails, slide the battery upward until it clicks into place.
To Remove the Battery Pack: Press the battery release latch above the battery pack and slide the battery downward.
2.3.3 Installing the Belt Clip
- Align the grooves of the belt clip with those on the radio and push down until you hear a click.
- To remove, use a flat-bladed object to press the belt clip tab away from the radio, then slide the clip upward.
2.3.4 Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.
3. Operating Instructions
3.1 Radio Overview: Buttons and Controls

Keypad Controls:
- V/M: Short press to switch frequency or channel mode. Long press to toggle channel display mode (CH/FREQ/NAME).
- A/B: Short press to toggle upper (A) / lower (B) screen. Long press to switch Dual Watch modes.
- SWEEP (L): Short press to enter One-Touch search.
- EXIT: Short press to return from menu. Long press to enter frequency sweep mode.
- #: Long press to lock/unlock keypad. Short press for DTMF dial. Long press to scan on/off.
- 0 [space]: Long press to enter weather switch to select weather channel.
- MENU: Activates menu, selects menu items, confirms parameters.
3.2 Basic Operations
3.2.1 Power On/Off and Volume Adjustment
- Power On: Rotate the Volume/Power knob clockwise until you hear a click. The display will show a message or flash, then a frequency or channel.
- Power Off: Rotate the Volume/Power knob counter-clockwise until you hear a click.
- Adjust Volume: Rotate the Volume/Power knob clockwise to increase, counter-clockwise to decrease.
3.2.2 Main Band/Sub Band Select
In standby, press the [A/B] key to switch between the A (upper) and B (lower) displays. The selected display becomes the active listening and transmit frequency/channel.
3.2.3 VFO/Channel Switch
Press the [V/M] key to switch between VFO (Frequency) mode and Channel (MR) mode. In MR mode, the channel number is displayed. In VFO mode, 'VFO' is displayed.
3.2.4 Making a Call
- Channel Mode Call: Select a channel, then hold down the [PTT] key to transmit. Speak into the microphone.
- Frequency Mode Call: Switch to VFO mode, input the desired frequency, then hold down the [PTT] key to transmit.
- Receive a Call: Release the [PTT] key. The green LED will illuminate when receiving.
NOTE: For best reception, keep the microphone 2.5-5 cm from your mouth during transmission.
3.2.5 Wireless Copy Frequency (One-Touch Frequency Search)

This feature allows for quick frequency matching with other radios.
- Press and hold the SWEEP (L) key. The screen will display "SEARCH SWEEK...".
- If the radio receives an effective signal (strongest and stable), the received frequency will be displayed. If CTCSS or DCS is present, its value will also be displayed.
- Press the [MENU] key to save the searched frequency and CTCSS/DCS to a channel.

3.2.6 Using the Flashlight
The radio has a high-intensity LED flashlight.
- Press the [SK1] key once for continuous light.
- Press [SK1] again for strobe light (emergency signal).
- Press [SK1] a third time to turn off the light.
3.2.7 Emergency Alert
To activate, press and hold the [SK1] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press [SK1] to exit. Use only in actual emergencies.
3.2.8 FM Radio (65-108MHz)
- In frequency or channel mode, press [SK2] to turn on the radio.
- Select the desired frequency using the arrow keys or input directly.
- Press # to automatically search for a station.
- Press [SK2] to exit FM radio.
3.2.9 NOAA Weather Radio/Scan Weather Channel
The radio can receive weather reports from designated NOAA stations and scan all 10 NOAA Weather Radio channels.

- To turn on NOAA Weather Scan, press the [OSQL] key for 3 seconds. A cloud icon will appear, and the radio will enter Weather band mode.
- Press and hold the # key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Pressing and holding # again for 3 seconds will stop the scan.
- After stopping the scan, you can manually select a weather channel using the arrow keys.
- To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Weather Channel Frequencies:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
NOTE: These are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
3.3 Advanced Features
3.3.1 Working the Menu System
The radio's menu system allows customization of various settings. Each menu item has a numerical value for direct access.
Basic Use with Arrow Keys:
- Press [MENU] to enter the menu.
- Use the ▲/▼ keys to navigate.
- Press [MENU] again to select an item.
- Use ▲/▼ keys to select the parameter.
- Press [MENU] to confirm and save, or [EXIT] to cancel.
- Press [EXIT] to exit the menu.
Using Shortcuts (Numerical Keypad):
- Press [MENU].
- Enter the numerical value of the menu item (e.g., '19' for scanner mode).
- Press [MENU] to enter the item.
- Enter the desired parameter using the numerical keypad or arrow keys.
- Press [MENU] to confirm and save, or [EXIT] to cancel.
- Press [EXIT] to exit the menu.
3.3.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. It can scan in VFO mode (by frequency step) or Channel mode (by channels).
Setting Scanner Mode:
- Press [MENU], then enter '19'.
- Press [MENU] to select.
- Use ▲/▼ keys to select scanning mode (Time, Carrier, or Search).
- Press [MENU] to confirm and save.
- Press [EXIT] to exit.
Scanning Modes Explained:
- Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
- Carrier Operation (CO): Scanner stops on a signal, then resumes after a preset time if the signal disappears.
- Search Operation (SE): Scanner stops on a signal and waits for manual resume.
Frequency Scanning: In VFO mode, press and hold # for more than 2 seconds to start scanning. Use ▲/▼ to change direction. Press # to stop.
Channel Scanning: In Channel mode, press and hold # for more than 2 seconds to start scanning. Use ▲/▼ to change direction. Press # to stop.
3.3.3 Manual Programming (Channels Memory)
The radio has 999 memory channels. Channels can store receive/transmit frequencies, power, signaling, bandwidth, and a 6-character alphanumeric identifier.
Frequency Mode (VFO) vs. Channel Mode (MR):
- VFO Mode: For temporary frequency assignments or quick field programming.
- MR Mode: For selecting pre-programmed channels.
Press [V/M] to switch between modes.
3.3.4 DTMF (Dual-Tone Multi-Frequency)
DTMF is used for automation systems and remote control, commonly in amateur radio repeaters. The keypad keys correspond to DTMF codes.
To Send DTMF Codes: Press the corresponding key(s) while holding down the [PTT] key.
3.3.5 Customization (Menu 29-58)
The radio allows customization of visual and audible features like display illumination, power-on message, keypad beep, Roger Beep, and voice prompt.
- Display Backlight (ABR) - Menu 51: Set backlight duration (5, 10, 15, 20, 30, 60 seconds) or always on.
- Beep Prompt (BEEP) - Menu 32: Enable/disable key press beep tone.
- Voice Function (VOICE) - Menu 30: Enable/disable voice prompts.
- Language of the MENU (LANGUAGE) - Menu 29: Select English or Chinese.
- Working Mode (MDF-A) - Menu 39: Select display mode (Frequency, Channel, or Name).
- Roger Beep (ROGER) - Menu 33: Enable/disable end-of-transmission tone.
- Power On Message (POWER ON MSG) - Menu 40: Customize the welcome message (Voltage, Message, or Logo).
- Power On Password (Power On PWD) - Menu 37: Enable/disable a password requirement at startup. Default is 000000.
4. Maintenance
4.1 Battery Maintenance Instructions
- Regularly wipe accumulated dust from the charging connector with a clean, dry cloth.
- Charge the battery between 5°C and 40°C (40°F and 105°F).
- Turn off the radio when charging a battery attached to it to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging.
- Do not overcharge the battery, as it shortens battery life.
- Do not expose the battery to direct sunlight or heat sources.
- Do not squeeze, penetrate, or remove the housing of the battery.
4.2 How to Store the Battery
- If storing the battery, keep it at approximately 80% discharged.
- Store in a low-temperature, dry environment, away from hot places and direct sunlight.
- Do not short-circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Do not store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire.
5. Troubleshooting Guide
If you encounter issues, refer to the table below. If problems persist, contact your dealer for technical support.
| Phenomena | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio. | Battery installed improperly. Battery power low. Poor battery contact. | Remove and reattach battery. Recharge or replace battery. Clean battery contacts or replace battery. |
| Weak or intermittent voice during reception. | Battery voltage low. Volume level low. Antenna loose or incorrectly installed. | Recharge or replace battery. Increase volume. Turn off radio, remove and reattach antenna. |
| Cannot communicate with other group members. | Frequency or signaling type inconsistent. Too far from other members. | Verify TX/RX frequency and signaling type. Move closer to other members. |
| Radio keeps transmitting. | VOX turned on or headset not installed. | Turn off VOX function. Check headset connection. |
| Unknown voices or noise. | Interrupted by radios on same frequency. Analog mode with no signaling. | Change frequency or adjust squelch level. Request dealer to set signaling for current channel. |
| Unable to hear due to noise/hiss. | Unfavorable position (blocked by buildings/underground). External disturbance (electromagnetic interference). | Move to open area, restart radio. Stay away from interfering equipment. |
6. Specifications
| Parameter | Value |
|---|---|
| Frequency Band | FM65-108MHz; AM108-136MHz(Rx); 350-390MHz(Rx); 136-174MHz (Rx/Tx); 220-260MHz (Rx/Tx); 400-520MHz (Rx/Tx); |
| Memory Channels | 999 |
| Power Supply | Li-Ion battery 7.4V/1400 mAh (BL-K6) |
| Operating Temperature | -10°C to +45°C |
| Working Mode | Monoband/Dualband |
| Modulation | F3E(FM) |
| Max. Frequency Deviation | ≤ ±5KHz |
| Spurious Radiation | < -60dB |
| Frequency Stability | ±2.5 ppm |
| Rx Sensitivity | < 0.2uV |
| Audio Output Power | ≥ 500mW |
| Dimensions (LxAxP) | 64x121x35mm |
| Weight | 240g |
Specifications are subject to change without notice.
7. User Tips
No specific user tips were available from the provided data.
8. Warranty and Support
8.1 Disclaimer
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With continuous development, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, or dissemination of this handbook may be made in any form without prior written authorization.
8.2 Technical Support
If you have any problems that cannot be resolved using this manual, please contact your dealer for technical support.
Manufacturer: Fujian Baofeng Electronics Co., Ltd.
Address: Changfu Industrial Zone, Xiamei, Nan'an, Quanzhou, Fujian, China