Harley-Davidson RH1250S

Contents

User Manual: Rear LED Brake Turn Signal Tail Light Fender Eliminator

For Harley Sportster S 1250 RH1250S (2022-2026 Models)

1. Product Information

This product is an aftermarket motorcycle accessory designed to replace the original rear fender, integrating LED brake lights and turn signals for a cleaner, 'tidy tail' look.

  • Product Name: Motorcycle Accessories
  • Model: RH1250S (LGXWHH Batch)
  • Batch/Serial Number: 959696940
  • Material: Stainless steel
  • Color: Black
  • Surface Finish: Painted protective layer
  • Production Process: Laser cutting / NC bending
  • License Plate Lighting: Red light / Brake light
  • LED Turn Signals: Amber light
  • Placement on Vehicle: Rear side
  • Weight: Approximately 0.88 kg (packaged)

Compatibility: This product is specifically designed for Harley Sportster S 1250 RH1250S models from 2022 to 2026.

2. Safety Warnings

  • Professional Installation: Installation must be performed by a qualified motorcycle technician.
  • Torque Wrench Use: A torque wrench must be used during installation to ensure proper tightening.
  • Pre-Ride Inspection: Inspect the part before every ride. Discontinue use immediately if looseness, deformation, or cracks are detected.
  • Aftermarket Part: This is a non-OEM (aftermarket) part. Its performance may differ from original equipment. Carefully assess its intended usage scenario.
  • No Modifications: Do not weld, drill, grind, or otherwise modify this product.
  • Compatibility: This product is only compatible with specified motorcycle models. Installation on non-compatible vehicles may cause improper fitment, functional failure, or safety hazards. Forced installation may lead to accidents.
  • Road Use: Some models are not E-mark certified and are intended for off-road or closed-course use only. Do not use on public roads unless explicitly labeled as "E-marked."

3. Setup and Installation Instructions

This product is designed for easy installation without complex instructions, but professional installation is recommended.

3.1 Components Overview

Disassembled view of the LED light strip and license plate bracket
Figure 1: Disassembled LED light strip and license plate bracket components.
Assembled view of the LED light strip and license plate bracket
Figure 2: Assembled LED light strip and license plate bracket.
Close-up of the LED light strip component with wiring
Figure 3: Close-up of the LED light strip with integrated wiring.
Close-up of the license plate bracket component
Figure 4: Close-up of the license plate bracket.

3.2 Installation Steps

  1. Prepare Motorcycle: Park the motorcycle on a level surface and engage the main stand for stability.
  2. Remove OEM Component: Use appropriate tools to carefully remove the original OEM fender and lighting components.
  3. Align New Part: Align the new fender eliminator assembly with the existing mounting holes on the motorcycle.
  4. Insert Fasteners: Insert the included fasteners through the aligned holes.
  5. Tighten Bolts: Tighten all bolts using a torque wrench to the specified torque value. Warning: Never tighten by hand feel! Over-torquing can strip threads, and under-torquing may cause the part to detach during riding, leading to safety hazards.
  6. Test Stability: After installation, manually apply pressure to the installed part to test its stability. Ensure there is no unusual noise, play, or movement.

4. Operating Instructions

This fender eliminator integrates the rear brake light, license plate light, and turn signals into a compact unit. Once properly installed and wired, these functions operate in conjunction with your motorcycle's existing electrical system.

  • Brake Light: The integrated red LED light functions as a brake light, illuminating when the brake lever or pedal is engaged.
  • License Plate Light: The red LED light also serves as a license plate light, providing illumination for your license plate.
  • Turn Signals: The amber LED lights function as turn signals, activated by your motorcycle's turn signal switch.

4.1 Visual Demonstration

Video 1: Demonstration of the integrated brake light and amber turn signals in operation.

4.2 Installed Appearance

Rear view of a white Harley Sportster S 1250 with the fender eliminator installed
Figure 5: White Harley Sportster S 1250 with the fender eliminator installed.
Rear view of a black Harley Sportster S 1250 with the fender eliminator installed
Figure 6: Black Harley Sportster S 1250 with the fender eliminator installed.
Rear view of a yellow Harley Sportster S 1250 with the fender eliminator installed
Figure 7: Yellow Harley Sportster S 1250 with the fender eliminator installed.

5. Maintenance Recommendations

  • Fastener Tightness: Check fastener tightness every 500 kilometers or once per month, whichever comes first.
  • Cleaning: Clean with water or a neutral detergent. Avoid strong acids or alkalis, which may cause corrosion.
  • Environmental Factors: If used in off-road, muddy, or salt-spray environments, increase inspection frequency to prevent premature wear or corrosion.

6. Troubleshooting

If you experience issues with your fender eliminator, consider the following common troubleshooting steps:

  • Lights Not Functioning:
    • Check all wiring connections for secure fitment.
    • Inspect for any pinched or damaged wires.
    • Verify that the motorcycle's fuses are intact and not blown.
    • Ensure proper grounding.
  • Incorrect Flashing (Turn Signals):
    • LED turn signals may require an LED flasher relay or load resistors to prevent hyper-flashing. Consult a qualified technician if this occurs.
    • Check for proper wiring of the turn signals.
  • Loose Fitment:
    • Re-check all mounting bolts and ensure they are tightened to the correct torque specifications.
    • Inspect for any signs of wear or damage to the mounting points or the bracket itself.

If problems persist, consult a qualified motorcycle technician.

7. Specifications

Feature Detail
Material Stainless steel
Color Black
Surface Finish Painted protective layer
Production Process Laser cutting / NC bending
License Plate Light Red LED (Brake Light Function)
Turn Signals Amber LED
Compatibility Harley Sportster S 1250 RH1250S (2022-2026)
Weight (approx.) 0.88 kg (packaged)

8. User Tips

  • Ensure all electrical connections are waterproofed after installation to prevent issues from moisture.
  • Regularly check the brightness and functionality of all lights (brake, turn signals, license plate) to ensure road safety.
  • Consider using thread-locking compound on mounting bolts for added security, especially if riding on rough terrain.

9. Warranty and Support

For specific warranty information, please refer to the terms and conditions provided by your retailer or the manufacturer at the time of purchase. For technical support or inquiries regarding this product, please contact the seller directly.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

10. Disclaimer

The manufacturer and EU Authorized Representative shall not be held liable for any damage, injury, or accident resulting from:

  • Incorrect or unqualified installation.
  • Use beyond the intended scope (e.g., on public roads without E-mark certification, if applicable).
  • Unauthorized modifications to the product.
  • Failure to inspect or maintain the product as instructed in this manual.

This manual may be updated without prior notice. Please refer to the latest version for current information.

© 2024 All Rights Reserved. Information subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.