IKSLED 17T Touch sensor

Contents

IKSLED 17T Touch Sensor LED Dimmer Switch

User Instruction Manual

1. Introduction

Thank you for choosing the IKSLED 17T Touch Sensor LED Dimmer Switch. This device is designed to provide convenient touch control and stepless dimming for your LED lighting, featuring a dual memory function for enhanced user experience. Please read this manual carefully before installation and use to ensure proper operation and safety.

2. Safety Information

WARNING: Please strictly follow the instructions and safety tips below. Use the product with caution.

  • Ensure the power supply is disconnected before installation or maintenance.
  • This device is designed for low-voltage DC LED lighting systems only.
  • Do not exceed the maximum load power specified for your voltage.
  • Avoid using this switch with incompatible equipment as listed in the 'Usage Precautions' section.
  • Keep the device away from water and high humidity environments.

3. Package Contents

  • 1 x IKSLED 17T Touch Sensor LED Dimmer Switch

4. Product Overview

The IKSLED 17T Touch Sensor is a compact and intuitive dimmer switch for LED strips. It offers precise control over your lighting with simple touch gestures.

Key Features:

  • Touch Control: Short touch for On/Off, long touch for stepless dimming.
  • Dual Memory Function: Remembers both the last brightness setting and the On/Off status before power-off.
  • Indicator Light Control: The blue indicator light can be turned On or Off with two quick touches.
  • Wide Voltage Compatibility: Supports DC 3V, 3.7V, 5V, 12V, and 24V systems.
Multiple IKSLED Touch Sensor LED Dimmer Switches

Figure 1: IKSLED Touch Sensor LED Dimmer Switches

Touch Sensor with Memory Function details

Figure 2: Touch Sensor highlighting its memory function

Video 1: Demonstration of the touch sensor's on/off, dimming, and indicator light control features.

5. Setup & Installation

5.1 Physical Installation

The switch requires a Ø17mm hole for mounting. Ensure the mounting surface is clean and dry before installation.

Installation diagram showing 17mm hole and switch dimensions

Figure 3: Installation dimensions and required hole size (Ø17mm)

5.2 Wiring Instructions

Connect the wires exactly as shown in the wiring diagram below. Pay close attention to polarity (positive and negative connections).

Wiring diagram for the touch sensor switch

Figure 4: Wiring Diagram. Connect Power+ to the positive terminal of your power supply, LED+ to the positive terminal of your LED strip, Power- to the negative terminal of your power supply, and LED- to the negative terminal of your LED strip.

  1. Wiring: Connect the wires from the switch to your power supply and LED strip according to the diagram.
  2. Fix the Switch: Securely fix the induction switch in place within the Ø17mm hole.
  3. Power On: Finally, turn on the power to use the switch.

5.3 Usage Precautions

Please note: This induction switch is prohibited from being used to control the following equipment:

  • Motors
  • Solenoid valves
  • Solar lights
  • Constant current lamps
  • Other inductive loads

Using the switch with these incompatible loads may cause malfunction or damage to the switch or the connected equipment.

6. Operating Instructions

The IKSLED touch sensor offers intuitive control over your LED lighting.

  • Turn On/Off: Lightly touch the sensor surface once (short touch) to toggle the LED lights On or Off.
  • Stepless Dimming: Press and hold your finger on the sensor surface (long touch) to smoothly adjust the brightness. Release your finger when the desired brightness is reached.
  • Indicator Light Control: Quickly double-touch the sensor surface to turn the blue indicator light On or Off.
Touch sensor showing On/Off operation

Figure 5: Short touch to turn On/Off

Touch sensor showing dimming from 0% to 100%

Figure 6: Long press for stepless dimming

Touch sensor indicator light turning on and off with double touch

Figure 7: Double-touch to control the indicator light

7. Maintenance

The IKSLED touch sensor switch requires minimal maintenance. To ensure longevity and proper function:

  • Keep the sensor surface clean and free from dust or debris. Use a soft, dry cloth for cleaning.
  • Avoid using abrasive cleaners or solvents, as these can damage the surface.
  • Ensure the wiring connections remain secure.

8. Troubleshooting

Symptom: Light cannot be controlled

After connection, the LED light stays permanently on or permanently off, and cannot be controlled by the switch.

Possible Causes & Solutions:

  1. Voltage Mismatch:
    Cause: The working voltage of the adapter does not match the LED light, or the adapter is not a constant voltage DC power supply.
    Solution: Confirm your adapter is a constant voltage DC power supply (e.g., 3.7V, 5V, 12V, 24V) and that its output voltage matches the voltage requirement of your LED light (DC 3.7V, 5V, 12V, or 24V).
  2. Reverse Polarity:
    Cause: The input/output or positive/negative (+/-) poles are connected in reverse.
    Solution: Verify the connections for input/output and positive/negative (+/-) poles according to the wiring diagram (Figure 4). If reversed, disconnect the power and reconnect them correctly.
  3. Installation Error:
    Cause: The switch was fixed after power-on, or it is not fixed securely and keeps moving during use, causing it to constantly re-detect the environment.
    Solution: Turn off the power. Securely fix the induction switch in place to prevent movement. Then, turn the power back on to test.

9. Specifications

ParameterDetails
Model Number17T Touch sensor
Working VoltageDC 3V, 3.7V, 5V, 12V, 24V (Constant Voltage)
Max. Load Power3V: < 5W
3.7V: < 9W
5V: < 15W
12V: < 36W
24V: < 48W
Sensing MethodShort touch: Turn On/Off
Long press: Stepless dimming
FeaturesTouch sensor dimmer, Dual Memory Function
MaterialAluminium alloy
Cutout DiameterØ17mm
CertificationCCC, CE, EMC, LVD, ROHS, SAA

10. User Tips

  • Careful Handling: While the product is robust, handle it carefully during installation to prevent any potential damage to the switch or wiring.
  • Power Supply: Ensure you use a compatible constant voltage DC power supply (transformer) that matches the voltage of your LED strip. This is crucial for proper function and to avoid damage.
  • Testing: Before final mounting, it's advisable to test the switch with your LED strip and power supply to confirm all connections and functions are correct.

11. Warranty & Support

This IKSLED product comes with a 12-month warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase.

For technical support, troubleshooting assistance, or warranty claims, please contact your seller or the IKSLED customer service team through the platform where you purchased the product.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.