1. Introduction
The RAKONCNC Handheld Laser Welding Machine is a versatile 3-in-1 tool designed for welding, cutting, and cleaning applications. It offers high accuracy, long service life, and is suitable for various industrial and manufacturing processes. This machine is engineered for efficiency and ease of use, providing fast and precise results on different metal surfaces.

2. Safety Precautions (Required Reading)
Hazard: Laser Radiation
- Never look directly at the laser beam or reflected light.
- Dedicated laser safety glasses must be worn.
- Protective screens must be set up in the welding area; unauthorized personnel are prohibited from entering.
- Remove reflective items such as metal watch straps and jewelry while working.
Warning: Fire Risk
- Flammable and explosive materials must not be placed within 2 meters of the work area.
- Fire extinguishers must be readily available.
- Unattended operation of equipment is strictly prohibited.
Note: Other Hazards
- Equipment must be properly grounded.
- Maintain ventilation during welding.
- Do not squeeze or step on the welding torch cable.
3. Equipment Components
The RAKONCNC Handheld Laser Welding Machine consists of the following main components:
- Main Unit: Includes the laser source, control system, and water chiller.
- Handheld Welding Torch: Equipped with a fiber optic cable for precise laser delivery.
- Wire Feeding Mechanism: An automatic wire feeder for continuous operation.
- Accessories: Safety goggles, various nozzles, and protective lenses.



4. Setup Procedure
Pre-start Checks
- Ensure the coolant level in the water chiller is normal.
- Verify that the protective lens is clean and free from debris.
- Check that the wire feed nozzle is unobstructed.
- Confirm that the grounding wire is securely connected to prevent electrical hazards.
Startup Sequence
- Connect the main power supply to the machine.
- Start the water chiller and wait for the water temperature to stabilize (approximately 30 seconds).
- Turn on the laser key.
- Start the control software. The standby green light should illuminate, indicating the machine is ready.
5. Operating Instructions
Test Weld
- Maintain a nozzle distance of 10-15mm from the workpiece.
- Press the switch on the welding torch and observe the position of the red light indicator point on the workpiece.
- Perform a test of the laser beam without wire feeding to ensure proper alignment and power.
Arc Initiation Welding
- Tilt the welding torch at approximately a 75-degree angle relative to the workpiece.
- Press the laser switch first, then press the wire feed button shortly after to initiate the welding process.
- Maintain a constant speed during welding, pausing for no more than 0.3 seconds to ensure a consistent weld bead.
Supported Welding Methods

Applications
The RAKONCNC laser machine is suitable for a wide range of applications:
- Metal surface cleaning
- Removal of paint from metal surfaces
- Cleaning of stains on surfaces
- Surface coating cleaning
- Pretreatment of welding surfaces
- Stone surface cleaning
- Rubber mold residue cleaning


6. Maintenance
Daily Shutdown Procedure
- Stop laser emission.
- Turn off the laser key.
- Continue water flow for 5 minutes to cool down the system.
- Turn off the main power.
- Clean the nozzle and protective lens.
Routine Maintenance
- Check the protective lens every 4 hours; replace immediately if contaminated or damaged.
- Empty the water tank filter daily.
- Check the wire feed tube for wear weekly.
- Clean radiator dust monthly to ensure efficient cooling.
7. Troubleshooting
This section provides general troubleshooting tips. For specific issues, please refer to the detailed manual or contact technical support.
- No Laser Output: Check power connections, laser key status, and ensure the control software is running correctly. Verify safety interlocks are engaged.
- Poor Weld Quality: Adjust nozzle distance, welding speed, laser power, and wire feed rate. Ensure the protective lens and nozzle are clean.
- Overheating: Check water chiller coolant level, ensure proper ventilation around the machine, and clean radiator dust.
- Wire Feed Issues: Inspect the wire feed tube for wear or obstructions. Ensure the wire spool is correctly installed and not tangled.
8. Specifications
| Feature | Specification |
|---|---|
| Model | RCW1000 / RCW1500 / RCW2000 |
| Laser Wavelength | 1070 ± 20nm |
| Laser Power | 1000W / 1500W / 2000W |
| Operating Mode | Continuous / Pulse |
| Length of Fiber - Optical | 10m |
| Interface of Fiber - Optical | QHB |
| Model Life | 100,000 hours |
| Power Supply | 220V / 380V |
| Cooling Method | Water Cooling |
| Laser Energy Stability | <2% |
| Air Humidity | 10-90% |
| Recommended Welding Thickness (1000W) | Stainless steel, carbon steel 0-2mm; Galvanized sheet, aluminum 0-1.5mm |
| Recommended Welding Thickness (1500W) | Stainless steel, carbon steel 0-3mm; Galvanized sheet, aluminum 0-2mm |
| Recommended Welding Thickness (2000W) | Stainless steel, carbon steel 0-4mm; Galvanized sheet, aluminum 0-3mm |
| Language | Chinese Simplified, Chinese Traditional, English, German, Russian, etc. (customizable) |
| Focal Spot Diameter | 0.5mm |
| Pulse Width | 0.1-80MS |
| Welding Gap Requirements | ≤1.2mm |
| Certification | CE |
| Origin | Mainland China |


9. User Tips
- Practice Makes Perfect: Before working on critical projects, practice on scrap materials to get a feel for the machine's settings and your technique.
- Ventilation is Key: Always ensure adequate ventilation in your workspace to disperse fumes and maintain air quality.
- Regular Checks: Make it a habit to perform daily pre-start checks and adhere to the routine maintenance schedule to ensure optimal performance and longevity of your machine.
10. Warranty and Support
The RAKONCNC Handheld Laser Welding Machine comes with a Two Year Warranty. For any technical support, service inquiries, or to obtain a more detailed instruction manual and operation videos, please contact us directly.
Contact Information:
- Website: https://www.rakoncnc.com
- Email: Info@rakoncnc.com
A user manual in PDF format is also available for download or reference: View User Manual (PDF)