LED Front Grille Clearance Light Assembly

1. Introduction

Thank you for choosing the TAPNM LED Front Grille Clearance Light Assembly. This product is designed to enhance the visibility and aesthetic of your Toyota Tundra (2022-up, excluding TRD Pro models). This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your lights.

Figure 1: LED Front Grille Clearance Lights installed on a Toyota Tundra.

2. Package Contents

Please check the package for the following items:

• 4 x LED Grille-Mounted Clearance Marker Lights
• 1 x Y-shaped Wiring Harness
• Double-sided Tape (for thin grille edges)

Figure 2: Kit components including LED lights and wiring harness.

3. Setup and Installation

Before you begin: Ensure your vehicle's engine is off and the ignition is in the 'OFF' position. Disconnect the negative terminal of your vehicle's battery to prevent electrical shorts during installation.

1. Positioning the Lights: Determine the desired location for each of the four LED lights on your vehicle's front grille.
2. Attaching the Lights:
   • Clip the clamp of each LED light onto the edge of the grille.
   • If your grille edge is thin, use the included double-sided tape for a secure fit.
   • If your grille edge is thick, you may need to gently bend the clamp slightly to accommodate it.
3. Wiring Connection:
   • Connect all four LED lights to the provided Y-shaped wiring harness. Ensure connections are secure.
   • Route the main wire from the harness to a suitable power source. You can wire it to your vehicle's front lamp, parking light, or directly to the fuse box (consult your vehicle's manual for appropriate fuse taps if using the fuse box).
   • Ensure all wiring is neatly tucked away and secured to prevent damage from heat or movement.
4. Testing: Reconnect your vehicle's battery. Turn on your vehicle's lights to test the functionality of the newly installed grille lights.

Figure 3: Close-up of LED light unit and the upgrade interface for docking installation.

Figure 4: Example of LED lights installed on a Toyota Tundra grille.

4. Operating Instructions

The LED Front Grille Clearance Lights are designed to function as clearance lights, position lights, and running lights. Once properly installed and wired, they will illuminate automatically when your vehicle's corresponding lighting system (e.g., parking lights or headlights) is activated.

The lights are available in various colors:

• White: Provides a bright, clean illumination.
• Yellow: Offers a distinct amber glow, often used for enhanced visibility.
• Blue: Delivers a unique, modern appearance.
• Red: Provides a bold, striking visual.

Figure 5: Yellow LED Grille Lights illuminated.

Figure 6: White LED Grille Lights illuminated on a Tundra.

Figure 7: Red LED Grille Lights illuminated with wiring.

5. Maintenance

These LED lights are designed for durability and require minimal maintenance:

• Cleaning: Periodically clean the lens of the lights with a soft, damp cloth to remove dirt and debris. Avoid using abrasive cleaners or solvents, as these can damage the lens material.
• Inspection: Occasionally check the wiring connections to ensure they remain secure and free from corrosion.
• Damage: If any part of the light assembly or wiring appears damaged, it is recommended to replace the affected component to maintain safety and performance.

6. Troubleshooting

If your LED grille lights are not functioning as expected, consider the following:

• Lights Not Turning On:
  • Check all wiring connections to ensure they are secure and properly seated.
  • Verify that the power source you tapped into is active when your vehicle's lights are on.
  • Inspect any fuses related to the circuit you connected to; replace if blown.
  • Ensure proper grounding if applicable.
• Flickering Lights:
  • Check for loose connections in the wiring harness or at the power source.
  • Ensure the voltage supply is stable (DC 12V).

If troubleshooting steps do not resolve the issue, please contact customer support for assistance.

7. Specifications

Figure 8: Product showing SAE & DOT approval, ensuring street legality.

8. User Tips

No specific user tips or common questions were available for this product. For best results, ensure all electrical connections are tight and protected from the elements.

9. Warranty and Support

While quality control is strict, occasional defective items may occur. If you receive any defective product, please contact customer support immediately. We are committed to providing a satisfactory solution.

Customer service typically replies within 24 hours (excluding weekends and holidays).

10. Safety Information

• Always disconnect the vehicle's battery before performing any electrical work.
• Ensure all wiring is properly insulated and secured to prevent short circuits or damage.
• If you are unsure about any part of the installation process, it is recommended to seek assistance from a qualified automotive technician.
• Do not modify the product in any way, as this may void any implied warranty and could lead to malfunction or safety hazards.