1. Product Overview
The YIHUA 948D-IV is a versatile 5-in-1 multi-function professional welding station, integrating a precision hot air pencil rework station, hot tweezer soldering station, micro soldering station, desoldering station, and suction pen. This comprehensive station is designed for desoldering and soldering applications involving various through-hole and SMD components such as SOIC, CHIP, QFP, PLCC, BGA packages, and more. It is also suitable for working on small components found in mobile phone circuit boards, in-line sockets, transformers, LCD screens, and IC chips.
Its applications extend to heat shrinking, drying, paint removal, glue removal, defrosting, pre-heating, and glue soldering.

Figure 1: YIHUA 948D-IV 5-in-1 Precision Rework Station and its accessories.

Figure 2: Overview of the 5-in-1 multi-function professional welding station capabilities.
Video 1: Demonstrating the setup, operation, and various functions of the YIHUA 948D-IV 5-in-1 Precision Rework Station, including connecting components, adjusting temperatures, and using different tools like hot air gun, tweezers, soldering iron, and desoldering gun.
2. Setup Instructions
2.1. Initial Assembly
- Place the suction pen, desoldering gun, hot air gun, and soldering iron onto their respective holders.
- Connect the hot air gun, hot tweezer, soldering iron, desoldering gun, vacuum pump, and suction pen's vacuum pump to the main unit.
- Secure the cable guide and pull down the cable tie. Insert the cable into the slot of the cable guide and pull up the cable tie. The cable will be securely fastened.
- Connect the power cord to an electrical socket and turn ON the master power switch.

Figure 3: Step-by-step visual guide for connecting the various tools to the main unit.
2.2. Panel Introduction
Familiarize yourself with the control panel and rear connections:

Figure 4: Front Panel Controls
- Cool/Hot Air Mode Button/ Stand-by Button (Press to switch between cool and hot air; press and hold to enter stand-by mode)
- Air Adjustment Knob/ Function Knob
- Master Power Switch
- Manual/Auto Mode Button (Hot Air Rework Station)
- Temperature Increase/Decrease Button (Hot Air Rework Station)
- Power Button (Hot Air Rework Station)
- Temperature Increase/Decrease Button (Hot Tweezer Soldering Station)
- Power Button (Hot Tweezer Soldering Station)
- Temperature Increase/Decrease Button (Precision Soldering Station)
- Power Button (Precision Soldering Station)
- Temperature Increase/Decrease Button (Desoldering Station)
- Power Button (Desoldering Station)
- Power Button (Suction Pen)
- Operation Indicator (Suction Pen)
- Desoldering Gun
- Temperature Increase Button (Soldering Iron)
- Temperature Decrease Button (Soldering Iron)

Figure 5: Rear Panel Connections
- Receptacle (Suction Pen)
- Receptacle (Vacuum Tube)
- Receptacle (Desoldering Gun)
- Cooling Exhaust
- Receptacle (Soldering Iron Holder)
- Receptacle (Hot Tweezer)
- Receptacle (Precision Soldering Iron)
- Cable Guide
- Receptacle (Power Cord)
- ESD-safe Receptacle
- Receptacle (Connects with Receptacle in 22.)
2.3. Installing and Changing Heating Element
Attach the heating element to the soldering iron and place the soldering iron tip into the hole. Once in place, apply pressure to secure the heating element. Slot the soldering iron tip into the V-shaped groove and lift the soldering iron to separate the heating element.
WARNING: Please replace the hot air nozzle and heating element when the handpiece is completely cooled to avoid burn injuries. The handpiece MUST be placed onto the holder and turn OFF the power button after use. Turn OFF the station's master power switch, and DISCONNECT the power cord if the station is not in use for an extended period.
3. Operating Instructions
3.1. Hot Air Rework Station
To operate the hot air rework station:
- Manual Mode: Turn ON the power switch, press the hot air gun switch, then press and hold the stand-by button on the hot air gun handle to start the hot air gun. This is to prevent accidental activation and improve safety.
- Automatic Mode: Turn ON the power switch, then press the hot air gun switch to start the hot air gun.
- Press and hold the hot air pencil's power button for 1 second and pick up the hot air pencil to start. Alternatively, press the hot air pencil's start button to stop/start.
- Once the operation is complete, place the hot air pencil to its holder. Press the hot air pencil's power button once to turn OFF.
- When the hot air pencil stops putting out air, turn OFF the master power switch.

Figure 6: Hot Air Gun and Suction Tin Station in operation.
3.2. Hot Tweezer Soldering Station
Press and hold the hot tweezer soldering station's power button for about 1 second. Once the temperature has stabilized, the station is ready for use.

Figure 7: Hot tweezers in action for SMD rework and desoldering.
3.3. Precision Soldering Station
Press and hold the Precision Soldering station's power button for about 1 second. Once the temperature has stabilized, the station is ready for use.

Figure 8: Precision micro-soldering with the C245 iron.
3.4. Desoldering Station & Suction Pen
When desoldering, position the desoldering gun vertically on the solder joint. Once the solder has melted, press the desoldering gun's trigger to desolder the joint.
If solder residue remains in the holes, apply additional solder and repeat the desoldering procedure.
If a component pin is adhered and solder cannot be removed, reapply solder, melt it, and gently move the desoldering nozzle back and forth to nudge the pin. Then, press the desoldering trigger to remove the solder.
Press the suction pen's power button to lift the chip.

Figure 9: Strong power suction for IC removal using the suction pen.

Figure 10: 'Pht' preheating reminder for the desoldering station. The vacuum pump is inactive during preheating.
3.5. Temperature Control and Calibration
The YIHUA 948D-IV features 4 independent channels, allowing simultaneous use and temperature control for different tools.

Figure 11: Four independent channels for simultaneous operation.
To calibrate temperature:
- When the temperature has stabilized, press and hold the respective tool's temperature increase and decrease button for approximately 2 seconds.
- Enter the measured temperature using the increase/decrease buttons.
- Once entered, press the increase/decrease buttons simultaneously to confirm.
The temperature calibration function should be used when:
- Replacing the heating element.
- Replacing the circuit board.
- Replacing other internal components of the machine.
- The surrounding environment has changed.
The unit also supports °C/°F free switching. Rotate the main knob to switch between Celsius and Fahrenheit display.
3.6. Stand-by Mode
The Hot Tweezer & Precision Soldering Station and Suction Gun have sleep and standby functions. Stand-by timer can be set for 1-10 minutes for tweezers/soldering station, and 10-30 minutes for suction gun. When a station enters stand-by mode, press its respective power button to restart. When in sleep mode, press the desoldering gun's trigger to wake it. Pick up the respective handpiece(s) to wake the hot tweezer soldering station or precision soldering station.

Figure 12: Key features including stand-by mode and temperature unit conversion.
4. Maintenance
4.1. Soldering Station Maintenance
- If a layer of oxidization forms on the soldering iron tip, do not increase temperature. Instead, use a metal wool ball to remove the oxidization. Set the temperature to 300°C (572°F), gently rub the tip in the metal wool ball. Once partially removed, apply solder while rubbing until the tip is completely coated. Replace severely oxidized tips.
- DO NOT use metal files on the soldering iron tip. Replace deformed or rusted tips.
- Avoid excessive force on the soldering iron tip, as this can damage it.
- When idling after high-temperature operation, adjust the temperature to 250°C (482°F) or below. High idling temperatures accelerate heating element aging.
- After every operation, clean the soldering iron tip and tin it with a new layer of solder to prevent oxidization.
4.2. Hot Air Rework Station Maintenance
- Keep the air outlet clear and free of blockages at all times.
- Install hot air gun nozzles ONLY when the nozzle enclosure and nozzle have cooled. Install correctly without brute force, and do not over-tighten screws.
- Select appropriate nozzles based on operation requirements. For smaller nozzles, use maximum air volume with a relatively lower temperature setting. Complete operation in the shortest duration possible.
- Maintain a minimum distance of 2mm between the component and the hot air gun's nozzle.
- DO NOT allow hot air to come in direct contact with facial parts. Be aware of burn injuries.
- Upon first use, the hot air gun may emit white fumes, which will dissipate shortly.
4.3. Desoldering Gun Maintenance

Figure 13: Daily maintenance of the suction tin gun.
Regularly check the desoldering gun's indicator color. If the red area is greater than or equal to the blue area, clean the desoldering nozzle, heating element, and filter chamber.
Cleaning Filter Chamber: The filter chamber can only be removed after the desoldering gun has fully cooled. Replace components if:
- Unable to remove solder from the spring filter, or the filter has collected more than 2/3 of its capacity – Replace the spring filter.
- The retainer has hardened and cracked – Replace the retainer.
- The ceramic filter paper is hardened due to over-accumulation of solder and flux – Replace the ceramic filter paper.
Desoldering Nozzle and Heating Element Cleaning: The solder in the heating element's inner hole must ONLY be cleaned when completely melted. If the cleaning pin cannot be put through the heating element's inner hole, replace the heating element.
Heating Element Replacement: Remove the filter chamber and desoldering nozzle. Remove the locking screws to open the handpiece's case. Note the wire's correct polarity before removal. Remove the heating element's wire to remove the heating element. Assemble the desoldering gun in the reverse order of disassembly and calibrate the temperature.
5. Troubleshooting Guide
- S-E Error: This indicates that the station's sensor module is faulty. You need to replace the heating element (which includes the sensor modules). Alternatively, ensure the handle is properly connected. Turn OFF the power, connect the handle, then turn ON the station again.
- OCP Error: This indicates that the heating element is defective and needs to be replaced.
6. Technical Specifications

Figure 14: Detailed Technical Specifications.
| Attribute | Value |
|---|---|
| Model | 948D-IV |
| Rated Voltage Range | AC 220V~240V, 50Hz / AC 110V~127V, 60Hz |
| Max Power | 1410W |
| Control Unit Dimensions | L300xW340xH145mm ±10mm |
| Operating Ambient Temperature | 0°C~40°C / 32°F~104°F |
| Display | LED Nixie |
| Hot Air Rework Station Air Delivery | Compressor Motor, ≤55L/min |
| Hot Air Rework Station Temperature Range | 100°C~500°C / 212°F~932°F |
| Desoldering Station Temperature Range | 380°C~480°C / 716°F~896°F |
| Desoldering Station Suction Pressure | 0.05MPa (Measured from the Nozzle) |
| Desoldering Station Soldering Tip to Ground Resistance | <2 ohms |
| Hot Tweezer Soldering Station Temperature Range | 90°C~450°C / 194°F~842°F |
| Hot Tweezer Soldering Station Soldering Tip to Ground Resistance | <2 ohms |
| Soldering Station Temperature Range | 90°C~450°C / 194°F~842°F |
| Soldering Station Soldering Tip to Ground Resistance | <2 ohms |
7. User Tips
- Tip Cleaning: Always clean and tin your soldering iron tip after use to prevent oxidation and prolong its lifespan.
- Desoldering Technique: When using the desoldering station, ensure the solder is fully melted before pressing the trigger to avoid damaging the circuit board or component.
- Ventilation: Soldering produces fumes. Always ensure adequate ventilation in your workspace to avoid inhaling harmful fumes.
- Nozzle Installation: For the hot air gun, ensure the nozzle and its enclosure are completely cooled before attempting to install or remove a nozzle to prevent burns.
8. Warranty and Support
The company reserves the right to improve and upgrade products, product specifications, and design without notice. For future reference, please keep this manual.
This product should not be disposed of with general household waste. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.
For technical support or inquiries, please contact:
Guangzhou Yihua Electronic Equipment Co., Ltd.No.13 ShaJing East Road, YongXing Industrial District,
LongGui, GuangCong Road, GuangZhou, GuangDong
TEL: +86-20-87470526
FAX: +86-20-87470261