1. Introduction
The VaneAims FXBY6 Series offers a range of 22mm plane head push button switches, available with or without LED illumination, and in both momentary and latching operation types. Designed for industrial electrical applications, these switches are robust, reliable, and suitable for various control circuits with different voltage requirements.
2. Safety Precautions
- Disconnect Power: Before any installation, disassembly, wiring, or maintenance inspection, always ensure the power supply to the FXBY6 series control components is disconnected to prevent electric shock and fire.
- Bulb Replacement: Use the designated bulb replacement tool to avoid burning your hands when replacing bulbs.
- Wiring Requirements: Use wires that meet the specified voltage and current requirements. Tighten M3.5 wiring screws to a torque of 1.0 Nm. Avoid loose terminals to prevent fire due to overheating.
- Handle with Care: Do not subject the switch to excessive shock or vibration, as this may lead to deformation, damage, or poor performance.
- LED Voltage: LED elements are sensitive to voltage. If the maximum voltage used exceeds the rated voltage, the LED element may deteriorate due to overheating, resulting in reduced brightness, color change, or complete failure.
- External Noise: External noise, transient voltage, or transient current on the circuit can also damage LEDs. Follow recommended instructions for LED usage.
- Key Selector Switches: Ensure the key is fully inserted into the keyhole before operating a key selector switch to prevent damage.
3. Product Overview
The VaneAims FXBY6 series push button switches are designed for reliability and ease of use in various industrial applications. They feature a plane head design and are available with LED illumination in multiple colors.
Key Features:
- Operation Type: Momentary or Latching.
- Contact Type: Available in 1NO, 1NC, 1NO1NC, 2NO, or 2NC configurations.
- Illuminated Colors: RED, BLUE, YELLOW, WHITE, GREEN.
- Voltage Options: 6V, 12V, 24V, 110V, 230V (AC and DC compatible).
- Current Rating (Ith): 10A.
- Mounting Diameter: 22mm.
- Material: Plastic.
- Protection Level: IP65 (front of panel), IP20 (terminal).

Figure 1: VaneAims FXBY6 Push Button Switches in various colors.

Figure 2: Top view of VaneAims FXBY6 Push Button Switches.
4. Specifications
General Product Properties
- Brand Name: VaneAims
- Model Number: FXBY6
- Switch Type: Push Button Switch
- Material: Plastic
- Is Smart Device: No
- High-concerned chemical: None
- EU LVD Voltage: Low voltage: Below 50Vac or 75Vdc
Performance Specifications

Figure 3: Performance Specifications Table.
Detailed Electrical Specifications
| Parameter | Value |
|---|---|
| Rated insulation voltage | 600V |
| Rated energization current | 10A |
| Minimum applicable load (reference value) | 3V AC/DC |
| Contacts | Silver contacts |
| Voltage | Resistive Load (AC-12) | Inductive Load (AC-15) |
|---|---|---|
| 24V | 10A | 10A |
| 120V | 10A | 6A |
| 240V | 6A | 3A |
| 380V | 2A | 1.9A |
| Voltage | Resistive Load (DC-12) | Inductive Load (DC-13) |
|---|---|---|
| 24V | 8A | 4A |
| 120V | 2.2A | 1.1A |
| 240V | 1.1A | 0.55A |
5. Installation
5.1. Mounting the Switch
The FXBY6 series switches require a 22mm mounting diameter. Ensure the panel thickness is between 0.8mm and 6.0mm. The 3.2mm groove on the switch is designed to prevent rotation; it is not necessary to use it with markers or anti-rotation rings.

Figure 4: Product Dimensions and Mounting Hole Drawing.
Mounting Steps:
- First, remove the contact block from the switch component.
- Unscrew the locking ring from the operating part.
- Insert the operating part into the mounting hole on the front of the panel.
- Tighten the locking ring from the back of the panel. Use a locking ring wrench (MW9Z-T1) for recommended torque up to 2.0Nm. Do not overtighten.
- Finally, install the contact block to the operating section.
5.2. Contact Block Installation and Removal
The FXBY6 contact blocks feature a new structure that significantly reduces the extension length of the control components behind the panel. They are designed with a terminal sleeve one-piece finger-safe terminal structure, maintaining high-class protection against electrocution hazards during wiring and maintenance.

Figure 5: Contact Block Assembly.
Removal: To remove the contact block, simply toggle the pin lock lever to the left and pull it out.
Installation: Align the "TOP" mark on the operation section with the "TOP" mark on the contact block and insert it. Then, toggle the pin lock lever in the opposite direction to secure.
5.3. Wiring Instructions
Use copper wire with a gauge of 14-18 AWG. The M3.5 wiring screws should be tightened to 1.0 Nm. The terminals are designed for a maximum of 2 wires per terminal.

Figure 6: Contact Type Instructions.
Contact Types:
- Normally Open (NO): Disconnected normally, connects when pressed. (Typically blue contact block)
- Normally Closed (NC): Connected normally, disconnects when pressed. (Typically red contact block)
Wire Cross-Sectional Area: For a wire cross-sectional area of 2.0mm², up to 2 connections are supported per terminal.
Crimping: If using fork crimp terminals, ensure an insulation tube or insulation cladding is used. For 2 bar terminals, use a bar terminal without an insulation sheath. When directly connecting 2 wires, standardize the wire size.
LED Lighting Component Wiring Precautions:
LED elements are sensitive to external noise and transient voltages. If such conditions are expected, implement protective measures like RC elements or surge absorbers in your circuit. For AC circuits, a simple RC filter can be used. For DC circuits, a diode can be used to protect against reverse voltage.
6. Operation
Momentary Operation
A momentary switch remains in its actuated state only while pressure is applied. Once released, it returns to its original state.

Figure 7: Momentary Push Button Switch.
Latching Operation
A latching switch remains in its actuated state after being pressed and released. It requires another press (or rotation, depending on the model) to return to its original state.

Figure 8: Latching Push Button Switch.
For latching switches, to reset the button, press the lockout to pull out or rotate it. Both methods are safe and convenient.
7. Maintenance
Bulb Replacement
LED and incandescent bulbs can be replaced from the front of the panel. Use the bulb replacement tool (OR-55) for this task. Alternatively, the contact block can be removed from the back of the panel to access the bulb.
Steps for Bulb Replacement:
- Insert the bulb replacement tool into the lamp head.
- Turn the tool counter-clockwise while gently pressing to remove the bulb.
Cleaning
No specific cleaning instructions are provided. Generally, keep the switch free from dust and debris to ensure optimal performance.
8. Troubleshooting
- LED Not Lighting or Dim: Ensure the voltage supplied to the LED is within the rated range. Excessive voltage or external noise/transients can damage the LED. Check for proper wiring and consider adding noise suppression components if operating in a noisy environment.
- Contact Bounce: When using latching switches with push-pull or rotary reset, the main contact (especially NC contacts) may experience bounce. Consider preventive measures if this affects your application (reference value: 20ms).
- Key Selector Switch Malfunction: Always ensure the key is fully inserted into the keyhole before operating the switch. Operating with a partially inserted key can cause damage.
9. User Tips
- For optimal performance and longevity, always adhere to the specified voltage and current ratings.
- When installing multiple switches, ensure adequate spacing for heat dissipation and ease of maintenance.
- Regularly inspect wiring connections for tightness to prevent overheating and ensure reliable operation.
10. Frequently Asked Questions (FAQ)
- Q: Are samples available for testing?
A: Yes, samples can be provided if the necessary parts are in stock. Sample and courier costs will apply. - Q: Can custom products be manufactured based on my designs?
A: Yes, custom products can be manufactured according to your samples or technical drawings. We can also assist with building molds and fixtures. - Q: What drawing formats are supported for custom production?
A: We support both 2D (e.g., PDF, CAD, JPG) and 3D (e.g., STP, IGS, STL, SAT, PRT, IPT) drawing formats.
11. Additional Resources
A detailed user manual in PDF format is available for download here.
12. Contact Information
For further inquiries or support, please use the following contact details:
- Contact Person: Maike
- Email: VaneAims@foxmail.com, chenmaike3303@sina.com
- Mobile/WhatsApp/WeChat/Skype: +86 15058777695
- Address: Zone, Yueqing, Zhejiang, China