JHao Xin DRL

Contents

User Manual

White Light Angel Eye Lamp Tube Ballast Light Source Module

Brand: JHao Xin | Model: DRL | Batch/Serial Number: 3068996866573771

For BMW 5 Series G30 G38 2021-2023 LOW Car Headlight DRL Guide Strip

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JHao Xin DRL Angel Eye Lamp Tube Ballast Light Source Module. This product is designed as a 1:1 replacement for the original DRL guide strips in BMW 5 Series G30 G38 models from 2021-2023 with LOW front headlights, offering a high-quality solution for headlight DRL issues.

2. Safety Information

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow all installation and operation guidelines carefully to avoid injury or damage to the vehicle.

3. Product Specifications

Attribute Value
Product Name Daytime Running Light (DRL) Light Guide Strip
Model DRL
Item Type Angel Eyes
Applicable Vehicle BMW 5 Series G30 G38 (2021-2023 LOW Front Headlights)
Origin Mainland China
High-concerned chemical None
Package Length 20 cm
Package Width 14 cm
Package Height 11 cm
Package Weight 0.14 kg

4. Setup and Installation

This section outlines the steps required to install the DRL guide strip. Professional installation is recommended due to the complexity of headlight disassembly and reassembly.

4.1. Tools Preparation

  • Heat gun / oven
  • Flat-head screwdriver, plastic pry tools
  • Gloves, microfiber towel
  • Headlight sealant (butyl rubber is highly recommended)
  • Electrical tape / heat-shrink tubing
  • 12V power supply or car battery (for testing)

4.2. Standard Installation Procedure

  1. Remove the headlight assembly:
    • Open the hood of your vehicle.
    • Remove the headlight mounting screws (typically 2-4 screws).
    • Unplug the headlight connector.
    • Carefully remove the headlight assembly and place it on a soft cloth to prevent scratches.
  2. Open the headlight lens (critical step):

    This step requires careful handling to avoid damaging the headlight housing or lens. Two methods are commonly used:

    • Method A: Oven (most stable)
      • Preheat oven to 90°C - 150°C.
      • Place the headlight in the oven for 8-12 minutes to soften the sealant.
      • Wear gloves and gently pry the lens open using plastic pry tools.
    • Method B: Heat gun
      • Heat evenly around the headlight sealant with a heat gun.
      • Pry the lens while heating; do not concentrate heat on one spot to avoid burning the lens.
      • Rule: Pry only when the sealant is soft; do not force it.
  3. Remove the old guide light:
    • Locate the original DRL guide light / angel eyes within the headlight.
    • Unplug the LED driver connector.
    • Release any retaining clips or screws holding the old guide light.
    • Carefully take out the old guide light.
  4. Install the new guide light:

    The product is a 1:1 match for the original. Ensure correct orientation (Left/Right).

    Left DRL Guide Strip

    Image: Left DRL Guide Strip

    Right DRL Guide Strip

    Image: Right DRL Guide Strip

    Car diagram showing Left and Right headlight positions

    Image: Diagram for Left (L) and Right (R) placement

    • Insert the new guide light into the original position.
    • Secure any clips to ensure no movement.
    • Connect the LED driver module.
    • Test for proper lighting and correct color first (see Section 5. Operation).
  5. Cleaning and resealing:
    • Clean off all old sealant completely from the headlight housing.
    • Apply a new ring of butyl rubber sealant in the groove of the headlight housing.
    • Close the lens and press firmly to ensure a tight seal.
    • Heat the sealed area for another 30 seconds to fully melt the new sealant and ensure a waterproof seal.
    • Wipe off any dust or debris inside the lens before final sealing.
  6. Reinstall on the vehicle:
    • Reinstall the headlight assembly into its position on the vehicle.
    • Plug in the headlight connector securely.
    • Secure the headlight mounting screws.

Video: Demonstrating the flexibility of the DRL guide strips.

DRL installed in BMW headlight

Image: Example of DRL installed in a BMW headlight.

5. Operation

After successful installation, perform the following power-on tests:

  • Ignition On: Turn the vehicle ignition to the 'on' position. The DRLs should light up.
  • Headlights On: Turn on the vehicle's headlights. The DRLs should dim, which is normal operation.

6. Maintenance

Regular maintenance for your DRL guide strips primarily involves ensuring the headlight assembly remains sealed and free from moisture or dust. If you notice any condensation inside the headlight, it indicates a compromised seal that should be addressed promptly by re-sealing the lens as described in Section 4.2, step 5.

Keep the exterior of the headlight lens clean using a microfiber towel and appropriate automotive cleaning solutions to maintain optimal light output and appearance.

7. Troubleshooting

  • DRL not lighting up:
    • Check the polarity and connection of the LED driver module. Ensure all connections are secure and correctly oriented.
    • If there is still no lighting or if fault codes appear on your vehicle's dashboard, computer coding may be required. This is common for certain vehicle brands like Mercedes-Benz and BMW after replacing headlight components. Consult a qualified automotive technician for assistance with coding.
  • Headlight yellowing issues:
    • 90% of headlight yellowing is typically caused by long-term use of the DRL, where the ballast light source emits both strong and white light. Replacing the DRL guide strip with this product can effectively resolve this issue without needing to replace the DRL ballast chip.
    • 10% of headlight yellowing is usually due to DRL ballast damage. If the ballast is damaged, there will be no strong light, and yellowing will occur. Look for signs of burning in large areas around the ballast light. In such cases, both the ballast and the DRL guide strip must be replaced simultaneously to resolve the problem.
    • Important: It is crucial to identify the faulty component (DRL guide strip or ballast) before replacement. Simply replacing one part without addressing the root cause will not solve the yellowing issue. For a 100% resolution of headlight yellowing and brightness problems, consider replacing both the ballast chip and the DRL guide strip simultaneously.

8. User Tips

  • Always double-check all electrical connections before reassembling the headlight to avoid having to reopen the unit.
  • When using a heat gun, move it constantly to ensure even heat distribution and prevent localized overheating of the plastic.
  • Consider watching online video tutorials specific to your BMW model for headlight removal and opening, as visual guides can be very helpful.

9. Manufacturer and Support Information

Manufacturer: Yiwu Xinyu Trading Co., Ltd.

Address: Room 503, No. 22 Liuruitang Road, Choujiang Street, Yiwu City, Jinhua City, Zhejiang Province, Postal Code: 330782

Email: 51281048@qq.com

EU Authorized Representative: MJCM SARL .0033

Address: 752907452.78 Avenue des Champs-Élysées Office 326.

Email: mjcm190928@gmail.com

Importer: Yiwu Xinyu Trading Co., Ltd.

Address: Room 503, No. 22 Liuruitang Road, Choujiang Street, Yiwu City, Jinhua City, Zhejiang Province, Postal Code: 330782

Email: 51281048@qq.com

For further assistance or inquiries, please contact the manufacturer or authorized representative using the details provided above.

A PDF version of this user manual is also available for download. Please refer to the product page for the link.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.