Mercedes-Benz W639

Contents

Rear Bumper Reflector Light Cover User Manual

For Mercedes-Benz Vito / Viano W639 (2003-2014)

1. Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your new Rear Bumper Reflector Light Cover for Mercedes-Benz Vito/Viano W639 models. This product is designed to replace or upgrade your vehicle's existing rear bumper reflector light cover, enhancing visibility and maintaining the aesthetic integrity of your vehicle.

Part Numbers: A6398260040, A6398260140; A6398260440, A6398260540

For a comprehensive guide, you may also refer to the official user manual PDF: View PDF Manual

2. Safety Precautions

WARNING: To avoid electric shock, short circuit, vehicle damage, or personal injury, disconnect the vehicle battery before installation. Improper installation may result in signal failure, water leakage, or unsafe driving conditions. Read these instructions completely before starting.

  • Turn off the engine, remove the key, and disconnect the negative battery terminal to prevent electrical damage.
  • Do not touch the bulb or LED surface with bare hands to avoid contamination or burnout.
  • Do not use incompatible bulbs or non-original voltage power supply.
  • Work in a dry, well-ventilated area. Keep away from open flames or high-temperature devices.
  • If you are unfamiliar with vehicle electrical systems, consult a professional mechanic.

3. Tools Required

  • Screwdriver (Phillips / flat-head)
  • Clean cloth
  • Protective gloves
  • Electrical tape (if needed)
  • Plastic pry tool (recommended for removing trim panels)

4. Installation (Setup)

Follow these steps carefully to install the rear bumper reflector light cover:

  1. Locate the Assembly: Identify the rear bumper signal light assembly on your vehicle.
  2. Remove Trim: Use a plastic pry tool to carefully remove the surrounding decorative cover or trim without scratching the bumper.
  3. Remove Lamp Housing: Remove the mounting screws or fixing clips that hold the lamp housing in place.
  4. Disconnect Wiring: Gently pull out the lamp housing and unplug the original wiring connector.
  5. Remove Old Bulb (if applicable): Twist the bulb socket counterclockwise to remove it from the housing. Take out the old bulb and insert the new signal light bulb into the socket.
  6. Reinstall Socket: Reinstall the socket into the lamp housing and twist clockwise to lock.
  7. Connect New Wiring: Connect the wiring harness firmly to the new rear bumper signal light.
  8. Test Functionality: Test the turn signal function before final installation to ensure normal operation.
  9. Secure Housing: Place the lamp housing back into position and secure with screws or clips.
  10. Reattach Trim: Reattach the trim cover and make sure it fits tightly.
  11. Reconnect Battery: Reconnect the negative battery terminal.
Rear bumper reflector light cover installed on a Mercedes-Benz Vito/Viano W639

Image: Rear bumper reflector light cover installed on a Mercedes-Benz Vito/Viano W639.

Single rear bumper reflector light cover

Image: Front view of a single rear bumper reflector light cover.

Rear view of the reflector light cover showing mounting points

Image: Rear view of the reflector light cover showing mounting points.

5. Operating Instructions

This product functions as a passive reflector and a protective cover for your vehicle's rear bumper light. It does not require active operation. Once installed, it automatically enhances your vehicle's visibility to other drivers, especially in low-light conditions, by reflecting light. It also protects the internal light assembly from environmental elements and minor impacts.

6. Inspection After Installation

  • Test left and right rear turn signals.
  • Test hazard warning lights to confirm normal flashing.
  • Check for flickering, dim light, or abnormal operation.
  • Ensure the lamp assembly is fully sealed to prevent water or dust from entering.
  • Confirm no parts are loose and the bumper surface is undamaged.

7. Maintenance

  • Cleaning: Regularly clean the reflector surface with a soft cloth and mild automotive soap to ensure maximum reflectivity. Avoid abrasive cleaners.
  • Inspection: Periodically check for any cracks, damage, or looseness. Replace if damaged to maintain safety and appearance.
  • Important Note: Do not expose the lamp to high-pressure car wash water directly for at least 24 hours after installation.

8. Troubleshooting

  • Signal Flashes Too Fast: If the turn signal flashes too fast after installation, check for bulb damage or loose wiring connections.
  • Water or Condensation Inside: Ensure the lamp assembly is fully sealed. If water ingress occurs, re-check the seal and installation.
  • General Malfunction: Do not modify the original vehicle circuit without professional guidance. Consult a qualified mechanic for any persistent electrical issues.

9. Specifications

FeatureDetail
Model NameFor Mercedes Benz Vito Viano W639 2003-2014
OEM NO.A6398260040, A6398260140; A6398260440, A6398260540
Replacement Number6398260040, 6398260440
Item TypeRear Bumper Lights Assembly
Special FeaturesRear Bumper Reflector Light
MaterialABS
ColorRed
OriginMainland China
Package Length15 cm
Package Width10 cm
Package Height5 cm
Package Weight0.1 kg

10. User Tips

No specific user tips were available from customer reviews or Q&A for this product.

11. Frequently Asked Questions (FAQ)

No specific frequently asked questions were available for this product.

12. Warranty and Support

For any warranty claims, technical support, or further assistance, please contact the seller directly through your purchase platform. Keep this manual for future maintenance and reference.

© 2024 Product Manual. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.