HoldPeak HP-5000D

Contents

HoldPeak HP-5000D Digital Anemometer User Manual

Model: HP-5000D

1. Introduction

The HoldPeak HP-5000D is a versatile handheld digital anemometer designed for accurate measurement of wind speed, air flow (CFM), and temperature. Its compact, waterproof design, anti-interference touch buttons, and rechargeable battery make it ideal for a wide range of applications, from HVAC system checks to outdoor sports and drone flying.

HoldPeak HP-5000D Anemometer with accessories

Figure 1: HoldPeak HP-5000D Anemometer and included accessories.

Features and Characteristics:

  • Anti-interference touch buttons
  • Wind speed measurement (m/s, km/h, ft/min, knots, MPH)
  • Air volume measurement (CMM, CMS, CFM)
  • Temperature measurement (°C/°F)
  • Compact and waterproof design
  • Displays current, maximum, and minimum wind speed
  • Low battery indication function
  • Backlight display function
  • Rechargeable lithium battery with TYPE-C interface
  • Optional automatic power-off function
  • 360° rotatable sensor head for accurate measurements
  • Equipped with dual wind chill sensors
  • Tripod screw hole for stable mounting

2. Setup

2.1 Battery Connection

To protect the rechargeable battery during shipping, the battery cable may be disconnected. Before first use, you must connect the battery:

  1. Use the small screwdriver provided to unscrew the screws on the battery cover located on the back of the device.
  2. Carefully remove the battery cover.
  3. Locate the battery and its connector. Connect the battery cable, ensuring correct polarity (connect wires of the same color together).
  4. Place the battery back into its compartment and close the battery cover, securing it with the screws.
Battery connection steps for HP-5000D

Figure 2: Steps to connect the internal battery cable before first use.

2.2 Charging the Device

The HP-5000D features a built-in 400mAh rechargeable lithium battery with a Type-C interface. To charge the device:

  1. Connect the provided Type-C USB cable to the charging port on the side of the anemometer.
  2. Connect the other end of the USB cable to a standard USB power adapter (not included) or a computer USB port.
  3. Charging typically takes 2 to 3 hours for a full charge.

3. Operating Instructions

The device features anti-interference touch buttons for various functions. Refer to the button diagram below for quick identification.

Control panel diagram of HP-5000D Anemometer

Figure 3: Control Panel and Button Functions.

Button Functions:

  1. Power On/Off Button (①): Press and hold for more than 1 second to turn on. Briefly press to turn off.
  2. Wind Speed/Air Volume Function Switch Button (② MODE): Briefly press to switch between wind speed and air volume measurement functions.
  3. Wind Speed Max/Min/Real-time Value Switch Button (③ MAX/MIN): Briefly press to cycle through maximum, minimum, and real-time values of wind speed or air volume.
  4. Wind Speed/Air Volume Unit Switch Button (④ UNIT): Briefly press to switch units. For wind speed: m/s, km/h, ft/min, knots, MPH. For air volume: CFM, CMS, CMM.
  5. Set Air Volume Area Key and Temperature Unit Switch Button (⑤ SET): In wind speed mode, toggles between secondary display temperature units (°C/°F). In air volume mode, allows setting the duct cross-sectional area.
  6. Data Hold and Backlight Button (⑥ H/☀): Briefly press to hold the current data. Long press (for 3 seconds) to activate/deactivate the backlight.

3.1 Power On/Off and Auto Power-Off Setting

  1. Power On: Press and hold the Power On/Off Button (①) for more than 1 second, then release. The screen will fully display upon startup.
  2. Power Off: Briefly press the Power On/Off Button (①).
  3. Auto Power-Off Setting: In the power-off state, press and hold Button (①) for 5 seconds. The main display will show

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.