1. Introduction
The VaneAims FXB8L Series RCBO (Residual Current Circuit Breaker with Overcurrent Protection) is an advanced electrical protection device. It integrates the functions of a residual current device (leakage protector) and a miniature circuit breaker, providing comprehensive circuit protection against electric shock, overload, and short circuit. This manual provides essential information for the safe and effective installation, operation, and maintenance of your RCBO.
Figure 1: VaneAims FXB8L Series RCBO Units
2. Safety Information
- WARNING: Disconnect the power supply before wiring or performing any maintenance on the device. Failure to do so may result in electric shock or serious injury.
- Installation should only be performed by a qualified electrician in accordance with national and local electrical codes.
- Do not use the device if it appears damaged.
- Ensure proper grounding where required.
- Do not disassemble the device without authorization. If the device fails, replace it with a new one of the same specification.
3. Product Overview
3.1. Key Features
- Leakage Protection: Immediately cuts off the circuit upon detecting leakage current to prevent electric shock.
- Overload Protection: Automatically cuts off power when current exceeds rated capacity, preventing equipment damage.
- Short Circuit Protection: Rapidly interrupts power during a short circuit to prevent fire hazards and damage.
- Space Saving: Compact 1P+N DPN-style design (18mm width) integrates multiple protection functions.
- High Sensitivity: Detects small leakage currents (30mA rated residual action current) for enhanced safety.
- Resettable Design: Manual reset after fault clearance simplifies operation.
- Isolation Function: Provides reliable circuit isolation for safe maintenance.
Figure 2: Comprehensive Protection Features
3.2. Components and Indicators
- Wiring Terminals: Upper (N, L) and lower (N1, N2) terminals for secure electrical connections.
- Test Button (T): Yellow button labeled 'test monthly'. Used to simulate a leakage fault to verify RCBO operation.
- Operating Handle: Green toggle switch for manual ON/OFF control.
- Visual Indicator Window: Reflects the working state.
- Green: Normal operation (circuit energized).
- Red: Fault status (circuit tripped or de-energized).
- Flame Retardant Housing: High-performance insulating material for safety.
- Rated Current Marking: Clearly marked (e.g., C16 for 16A, C40 for 40A).
- Breaking Capacity: Marked short-circuit breaking capacity (6000A).
Figure 3: RCBO Component Descriptions
Figure 4: Visual Indicator Windows
4. Setup and Installation
4.1. Mounting
The FXB8L Series RCBO is designed for 35mm DIN-rail mounting, ideal for household and industrial distribution boxes.
Figure 5: 35mm DIN-Rail Mounting
4.2. Wiring Requirements
WARNING: Disconnect the power supply before wiring.
- Connect the live wire (L) to the L terminal and the neutral wire (N) to the N terminal at the top of the device.
- Connect the load's neutral wire to N1 and the load's live wire to N2 at the bottom terminals, strictly in accordance with the markings.
- Tighten all screws to ensure reliable connections and prevent loose contacts or overheating.
- Refer to the wiring diagram on the device for correct connections.
Wiring Diagram Schematic (as marked on device):
Top Terminals: N (Neutral Input), L (Live Input)
Internal: Test Button (T), ON/OFF Switch
Bottom Terminals: N1 (Neutral Output to Load), N2 (Live Output to Load)
Specifications on device: IEC61009-1, IΔn=30mA, IΔm=2kA, t≤0.1s
Figure 6: Device Wiring Schematic
4.3. Installation Environment
Install the RCBO in a dry, well-ventilated, and dust-free distribution box. Avoid environments with high temperature, high humidity, or corrosive substances.
5. Operation
5.1. Normal Operation
- To Turn ON: Push the operating handle up to the 'ON' position. The visual indicator window will show Green, indicating the circuit is energized.
- To Turn OFF: Push the operating handle down to the 'OFF' position. The visual indicator window will show Red, indicating the circuit is de-energized.
5.2. Test Button Function
The yellow 'T' test button is used to simulate a leakage fault and verify the normal operation of the RCBO's leakage protection function. It is recommended to press this button monthly as marked on the device. Upon pressing, the RCBO should trip (switch to OFF, indicator turns Red). Reset the device after testing.
6. Maintenance
- Regular Testing: Press the test button monthly to ensure the leakage protection function is working correctly.
- Cleaning: Keep the device clean and free from dust. Use a dry cloth for cleaning; do not use liquids or abrasive cleaners.
- Inspection: Periodically check wiring terminals for tightness and ensure there are no signs of overheating or damage.
- Replacement: Do not attempt to repair a faulty device. If the RCBO fails or is damaged, it must be replaced with a new one of the same specification.
7. Troubleshooting
7.1. Device Trips (Indicator Red)
If the RCBO trips (operating handle moves to OFF, indicator shows Red), it indicates a fault condition (leakage, overload, or short circuit).
- Identify the Fault: Disconnect appliances or circuits connected to the RCBO one by one to identify the source of the fault.
- Clear the Fault: Rectify the issue (e.g., unplug a faulty appliance, fix a short circuit, reduce load).
- Reset Operation: Once the fault is cleared, manually push the operating handle up to the 'ON' position to restore power. If the device trips again immediately, the fault has not been resolved or there is an internal issue with the RCBO.
7.2. Device Does Not Trip During Monthly Test
If the RCBO does not trip when the test button is pressed, the leakage protection function may be faulty. The device should be replaced immediately by a qualified electrician.
8. Specifications
The following specifications apply to the VaneAims FXB8L-63 RCBO. Specifications for other models in the FXB8L series (e.g., FXB8L-40) may vary slightly. A detailed PDF manual for FXB8L-40 is available at this link.
| Parameter | Specification |
|---|---|
| Product Model | FXB8L-63 (FXB8L Series) |
| Brand | VaneAims |
| Product Type | RCBO (Residual Current Circuit Breaker with Overcurrent Protection) |
| No. of Poles | 1P+N (2P L/N bipolar) |
| Rated Current | 6A, 10A, 16A, 20A, 32A, 40A, 63A (various ratings available) |
| Rated Voltage | AC 230V~ |
| Rated Frequency | 50Hz / 60Hz |
| Rated Short-Circuit Breaking Capacity | 6000A |
| Rated Residual Action Current (IΔn) | 30mA |
| Residual Current Off-time (t) | ≤0.1s |
| Rated Impulse Withstand Current (Iam) | 2kA |
| Standards | IEC61009-1 |
| Certifications | CE |
| Overall Dimensions (H x W x D) | 84.4mm x 36mm x 74mm (approx.) |
Figure 7: Product Dimension Diagram
9. User Tips
- Always ensure that the total current draw of connected devices does not exceed the RCBO's rated current to prevent nuisance tripping.
- If the RCBO frequently trips without an apparent fault, consult a qualified electrician to check for underlying electrical issues in your system.
- Keep the area around the RCBO clear to allow for proper ventilation and easy access for testing and resetting.
10. Warranty and Support
For warranty information and technical support, please refer to the seller's terms or contact your point of purchase. Keep your purchase receipt as proof of purchase.