1. Introduction
The FEASYCOM FSC-BT1026C is a dual-mode Bluetooth 5.1 stereo audio receiver module. It is built on the Qualcomm QCC3024, an entry-level flash-programmable Bluetooth Audio System-on-Chip (SoC). This module is designed with an extremely low-power architecture, enabling high-quality audio transmission and robust low-power Bluetooth connectivity for a wide range of wireless audio applications, including Bluetooth stereo audio devices.
The FSC-BT1026C module supports various audio profiles such as A2DP, AVRCP, and HFP. It also incorporates Qualcomm cVc voice technology and aptX audio codecs, ensuring superior audio performance for applications like wireless headphones, Bluetooth speakers, and car Bluetooth systems. The module comes preloaded with Feasycom’s powerful and user-friendly firmware, facilitating seamless integration and straightforward deployment, thereby helping manufacturers reduce development time and costs.
For detailed technical specifications and diagrams, please refer to the official datasheet: FSC-BT1026x Bluetooth 5.1 Dual Mode Module Datasheet (PDF).
2. Setup and Installation
2.1 Hardware Integration Suggestions
Proper hardware integration is crucial for optimal performance and reliability of the FSC-BT1026C module. Adhere to the following guidelines during design and assembly.
2.1.1 Soldering Recommendations
The FSC-BT1026C module is compatible with industrial standard reflow profiles for Pb-free solders. The specific reflow profile used should be determined by the thermal mass of the PCB, the heat transfer efficiency of the oven, and the type of solder paste. Consult the datasheet of your chosen solder paste for precise profile configurations.
Feasycom provides recommendations for soldering to ensure reliable solder joints. The optimal profile should be studied case by case, but general guidance includes:
- Pre-heat Zone (A): Raise temperature at a controlled rate (typically 0.5-2 °C/s) to preheat the PCB and components to 120-150 °C. This stage distributes heat uniformly and removes solvent to reduce thermal shock.
- Equilibrium Zone 1 (B): Flux becomes soft and encapsulates solder particles. Activators and rosin eliminate oxide film. Recommended temperature: 150-210 °C for 60-120 seconds.
- Equilibrium Zone 2 (C) (Optional): For upright components, maintain 210-217 °C for 20-30 seconds.
- Reflow Zone (D): The profile is designed for Sn/Ag3.0/Cu0.5. Peak temperature should be 230-250 °C. Soldering time above 217 °C should be 30-90 seconds.
- Cooling Zone (E): Fast cooling is recommended to ensure small solder grains for a durable joint. Typical cooling rate: 4 °C.
Refer to Figure 13 in the datasheet for a visual representation of the typical lead-free reflow profile.
2.1.2 PCB Layout Guidelines (Internal Antenna)
Good layout practices are essential for proper module operation. Avoid placing copper or any metal near the antenna, as it can degrade performance by affecting matching properties. Metal shields around the antenna will prevent radiation and should not be used. Use grounding vias separated by a maximum of 3 mm at the edge of grounding areas to prevent RF penetration and unintentional resonance. Ensure GND vias are placed all around the PCB edges.
The motherboard should not have bare conductors, traces, or vias in the restricted antenna area, as it is not covered by the stop mask print. This prevents mismatching the on-board antenna. Refer to Figure 15 in the datasheet for the restricted area layout.
2.1.3 PCB Layout Guidelines (External Antenna)
For external antenna designs, placement and PCB layout are critical. The trace from the module's RF port to an external antenna should be 50Ω and as short as possible to minimize interference. Keep the external antenna and RF-IN port away from noise sources and digital traces. A matching network may be required. Refer to Figure 16 in the datasheet for module placement on a system board and Figure 17 for antenna clearance space. Figure 18 illustrates recommended trace connections for the antenna.
- Keep trace/connection line length as short as possible.
- Maintain distance between connection and ground area on the top layer at least as large as the dielectric thickness.
- Avoid routing RF traces close to digital sections of the system board.
- Avoid sharp angles in microstrip line routing to reduce signal reflections; chamfers or fillets are preferred.
2.2 Pin Definition Descriptions
The FSC-BT1026C module features various pins for power, I/O, and interfaces. Understanding these definitions is crucial for correct integration.
A detailed table of pin definitions, including pin name, type, description, and notes, is available in Table 2 of the datasheet (pages 11-13). This table covers pins such as GND, NC/AIO4/LED4, AIO5/LED5, PCM_CLK/PIO16, UART, SPI, I2C, USB, and audio-related pins.
For a visual representation of the pin layout, refer to Figure 2 (Pin Diagram - Top View) in the datasheet.
2.3 Application Schematic
The application schematic provides a comprehensive overview of the module's typical wiring and connections for various functionalities, including power-on circuits, analog audio processing, and USB connections. Due to its complexity, the full application schematic is best viewed in the official PDF manual on page 39.
3. Operating Instructions
3.1 Power Management
The module's power management system includes a power supply and a battery charger.
3.1.1 Power Supply
The power rails of the module are supplied from an external voltage source. Ensure the transient response of any regulator used is 20µs or less, and the power rail recovers quickly.
3.1.2 Battery Charger
The FSC-BT1026C battery charger is OFF by default. It can provide up to 200mA of charge current internally. External configurations can support charge rates from 200 mA to 1800 mA with an external PNP pass device and resistor.
The charger system has five main operating states: Trickle Charge, Pre-Charge, Fast Charge (Constant Current and Constant Voltage), and Standby Mode. The current charger status can be read by application software. Refer to Figure 3 in the datasheet for the charge cycle states diagram.
- Trickle Charge: Engaged when VBAT is 0 to Vpre (deeply discharged battery). Provides a small current to safely charge and reset battery protection circuits.
- Pre-Charge: Engaged when VBAT is Vpre to Vfast. Allows a faster charge rate than trickle charge (10-20% of fast charge rate).
- Fast Charge:
- Constant Current: VBAT is Vfast to Vfloat. Maximum charge rate.
- Constant Voltage: VBAT is maintained at Vfloat, and current slowly reduces until termination (E), transitioning to Standby mode.
- Standby Mode: Charger does not charge but monitors battery voltage. Re-enters Fast Charge if voltage falls below Vfloat by a configurable threshold (Vhyst).
For battery protection, it is recommended that customer application software turns off the device at ~3.0 V to prevent irreversible damage from deep discharge.
The charger can operate in two modes: Headset mode (known current into battery) and Speaker mode (limits current from VCHG port, allows peak currents from battery during charging).
An external PNP pass transistor can be used for fast charge. The module senses charging current via an external sense resistor (between VCHG and VCHG_SENSE pins) and controls the PNP transistor's base current. The VCHG_SENSE pin should be routed directly to the external sense resistor for accurate voltage measurement. The VBAT_SENSE pin should be routed separately back to the battery.
The sense resistor (Rsense) value should be chosen to provide 100 mV voltage between VCHG and VCHG_SENSE pins at maximum charge current. For example, 100 mΩ for 1 A, 68 mΩ for 1.5 A. Use 1% or lower tolerance Rsense resistors.
3.2 PIO (Programmable Input/Output)
The FSC-BT1026C features 14 digital PIO pads, 5 pads for LED operation (LED[5:4, 2:0]), and 1 output on XTAL_CLKOUT. SYS_CTRL can be used for power-on signaling and as an input after boot.
PIOs can be configured with pull-up or pull-down resistors (weak and strong) and have programmable drive strength (2, 4, 8, or 12 mA). All PIOs are readable by all subsystems.
3.3 Serial Interfaces
The module supports UART, I2C, and USB interfaces.
3.3.1 UART Interface
The UART controller performs serial-to-parallel and parallel-to-serial conversions. It supports ten types of interrupts. The UART interface uses RS232 protocol for communication. UART_RX and UART_TX transfer data, while UART_CTS and UART_RTS can be used for RS232 hardware flow control. This module's output is at 3.3V CMOS logic levels; level conversion is needed for RS-232 compliant interfaces.
It is not recommended to link CTS and RTS except for testing, as it can lead to internal receive buffer overflow and processor crashes. Adhere to the correct CTS/RTS handshaking protocol. Refer to Figure 4 (UART Connection) and Figure 5 (Break Signal) in the datasheet.
Possible UART settings are detailed in Table 3 of the datasheet, including baudrate (2400 baud to 4Mbaud), flow control (RTS/CTS), parity (None, Odd, Even), number of stop bits (1/2), and bits per channel (8).
3.3.2 I2C Interface
The I2C interface is a two-wire, bi-directional serial bus for data exchange. It supports multi-master operation with collision detection and arbitration. Data is transferred synchronously to SCL on the SDA line byte-by-byte. Pull-up resistors are required externally for I2C operation. Refer to Figure 6 (I2C Bus Timing) in the datasheet.
3.3.3 USB Interface
The module has a USB device interface for connection to a host (phone/PC) or battery charging adapter. It operates as a USB2.0 Full Speed (12 Mb/s) port. The DP 1.5 k pull-up is integrated, and no series resistors are needed on USB data lines. Integrated ESD protection on data lines meets IEC 61000-4-2. The VCHG input is tolerant of 6.5 V and transients up to 7.0 V. The module supports charger detection to USB BCv1.2 standard.
3.4 LED Drivers
The module's LED drivers operate as open-drain pads, tolerable up to 7.0 V. The cathode of the LED should be connected to the module's LED pad. Each pad can sink up to 50 mA. The module has six PWM-based LED controllers for driving LEDs. The LED flash rate and ramp time can be configured via API. Multiple LED drivers can be synchronized for color change sequences on RGB LEDs.
3.5 Audio Subsystem
The audio subsystem includes analog DAC, analog ADC, I2S/PCM interface, and an audio engine. Refer to Figure 7 (Audio Subsystem Block Diagram) and Figure 8 (Analog Audio and Microphone Interfaces) in the datasheet.
- Analog DAC: Stereo analog outputs configurable as differential Class-AB or Class-D.
- Analog ADC: Stereo analog inputs configurable as single-ended, unbalanced, or balanced analog.
- I2S/PCM Interface: 1x bidirectional 24-bit I2S interface supporting 8, 16, 32, 44.1, 48, 96, 192 kHz sample rates. Also supports SPDIF interfaces (2, configurable as input/output). Refer to Table 4 and Figures 10, 11, 12 in the datasheet for I2S/PCM details.
- Audio Engine: 2 codec output channels and 6 codec input channels, supporting various sample rates. Digital mics (6 mono/3 stereo) supporting 500 kHz, 1, 2, 4 MHz clock frequencies. Includes 1 or 2-mic cVc headset noise reduction and echo cancellation technology. Supports SBC and AAC audio codecs, aptX, aptX HD, aptX Low Latency.
- Line/Mic Inputs: Two high-quality audio input ADCs (HQADC) for line input. Configurable with internal switch arrangement. Inputs should be AC coupled (typically with a 2.2uF capacitor). Refer to Figure 9 in the datasheet.
- Line/Headphone Outputs: Two high-quality audio output DACs (HQDAC) drive stereo low impedance differential loads (BTL headphones) or line out.
4. Maintenance and Handling
4.1 MSL & ESD Protection
The FSC-BT1026C module has integrated ESD protection on the USB_DP and USB_DN pins, detailed in IEC 61000-4-2. The module is rated MSL 3. Handle with care to prevent electrostatic discharge damage. Refer to Table 17 (MSL and ESD) and Table 18 (USB Electrostatic Discharge Protection Level) in the datasheet for specific ratings.
4.2 Recommended Temperature Reflow Profile
For manufacturing, ensure modules are packaged to prevent moisture absorption. New packages include desiccant and a humidity indicator card. If baking is required, follow instructions specified by IPC/JEDEC J-STD-033. The shipping tray cannot be heated above 65°C; modules must be removed if higher temperatures are needed. Refer to Table 19 (Recommended baking times and temperatures) and Figure 13 (Typical Lead-free Reflow Profile) in the datasheet.
4.3 Product Packaging Information
The module is typically supplied in tray vacuum packaging. Optional packing boxes are available. Refer to Figure 19 (Tray vacuum) and Figure 20 (Packing Box) in the datasheet for packaging details. Standard package is 1000 pieces per carton.
5. Troubleshooting
5.1 Resetting the Module
The FSC-BT1026C has a digital reset pin (RESET#) which is an active low signal. The pin has a fixed strong pull-up to VDD_IO and can be left unconnected. A continuous low logic (0V) on the UART_RX terminal for a duration longer than PSKEY_HOSTIO_UART_RESET_TIMEOUT will cause a reset. This feature allows a host to initialize the system to a known state.
The module is always powered if VCHG is present and does not power down if RESET# is asserted while VCHG remains present. Feasycom recommends powering down via software-controlled methods rather than external assertion of RESET#.
5.2 Common Issues and Solutions
- UART Communication Issues: If CTS and RTS pins are linked and the host sends data when the module deasserts its RTS signal, internal receive buffers may overflow, leading to a processor crash. Always adhere to the correct CTS/RTS handshaking protocol.
- Antenna Performance Degradation: Ensure no copper or metal is placed near the antenna area on the PCB. Follow layout guidelines for internal and external antennas to avoid interference and maintain matching properties.
- ESD Damage: Handle the module with appropriate ESD precautions to prevent damage to sensitive components.
- Battery Deep Discharge: Implement application software to turn off the device at approximately 3.0V to prevent irreversible damage to the Li-ion battery.
- Module Not Powering Up: Ensure SYS_CTRL is asserted for more than 20ms to start power up from the OFF state. If the module is in OFF or DORMANT state, a button press connected to SYS_CTRL can boot the device.
6. Specifications
This section provides key technical specifications for the FSC-BT1026C module. For complete details, refer to the official datasheet.
6.1 General Specifications
| Category | Feature | Implementation |
|---|---|---|
| Chip | QCC3024 (FSC-BT1026C) | |
| Wireless Specification | Bluetooth Version | V5.1 Dual-mode |
| Frequency | 2.402 - 2.480 GHz | |
| Transmit Power | +9 dBm (Maximum) | |
| Receive Sensitivity | -96.0 dBm (typ.) π/4 DQPSK; -89.0 dBm (typ.) 8DPSK; -100 dBm (typ.) BLE 1 Ms/s | |
| Raw Data Rates (Air) | 3 Mbps (Classic BT - BR/EDR) | |
| UART Interface | TX, RX, CTS, RTS (General Purpose I/O) | |
| Baudrate | Default 115200,N,8,1; Support from 1200 to 4000000 | |
| GPIO | 20 (maximum configurable) lines; O/P drive strength (2, 4, 8, or 12 mA); Pull-up resistor (33 KΩ) control | |
| I2C Interface | 1 I²C Master interface with speed up to 400 kbps | |
| SPI Interface | SPI debug and programming interface | |
| ADC Interface | Analog input voltage range | 0~1.854V |
| Resolution | 10-bit ADC; 1 channel (configured from GPIO total) | |
| USB Interface | 1 full-speed (12Mbps) | |
| Audio CODEC | Audio Codecs | aptX, aptX HD, aptX Low Latency, SBC and AAC |
| Signal Detection | Configurable to trigger events | |
| Parametric EQ | 1 bank of up to 10-stage Speaker Parametric EQ; 6 banks of up to 5-stage User Parametric EQ | |
| DAC Fidelity | Post Mastering to improve | |
| USB Audio | Stereo audio ADC with line input, stereo audio DAC | |
| Physical | Dimensions | 13mm(W) x 26.9mm(L) x 2.2mm(H); Pad Pitch 1mm |
| Operating Temperature | -40°C to +85°C | |
| Storage Temperature | -40°C to +85°C | |
| Supply Voltage | VDD_IO | 1.7 ~ 3.3V |
| Battery Input | VBAT_IN | 2.8V ~ 4.3V |
| Power Consumption | Play | 10mA (typ) |
| Pairing | 5mA (typ) | |
| OFF | 1uA (typ) |
For a complete list of specifications, including absolute maximum ratings, recommended operating conditions, and detailed electrical characteristics for various interfaces (USB, LED drivers, Stereo Codec, Auxiliary ADC, Microphone Bias Generator), please refer to sections 5.1 through 5.6 in the official datasheet.
7. User Tips
- Firmware Updates: Feasycom provides development and production tools for programming, updating, configuring, and debugging the module via the SPI interface. Regularly check for firmware updates to ensure optimal performance and access new features.
- Customization: For customized module functionality, certain pins can be reconfigured as I/O interfaces. Contact Feasycom for modifications or specific requirements.
- External Antenna Optimization: If using an external antenna, ensure proper impedance matching and maintain a 5mm clearance space from the antenna to maximize Bluetooth signal coverage.
- Power Supply Stability: Use a stable power supply with a fast transient response (20µs or less) to ensure reliable operation of the module.
8. Warranty and Support
The FSC-BT1026C module comes with a one-year warranty. Feasycom Technology reserves the right to make corrections, modifications, and other changes to its products, documentation, and services at any time. Customers should obtain the newest relevant information before placing orders.
For technical support, inquiries, or to obtain the newest relevant information, please contact Feasycom Technology directly. Their contact information can be found in the official datasheet.
Email: sales@feasycom.com
Website: www.feasycom.com