IKuaios E5 V3 V4 C612 X99

Contents

IKuaios Intel Xeon E5 V3 V4 C612 X99 Motherboard User Manual

Model: E5 V3 V4 C612 X99

1. Product Introduction

1.1 Brief Introduction

The BKHD-2011-MATX is an ATX-series motherboard designed for Xeon processors based on the LGA2011 platform. It is broadly applicable in commercial displays, communication control systems, medical equipment, industrial automation, financial devices, and cloud terminals.

The key features of the BKHD-2011-MATX motherboard are as follows:

  • Supports LGA2011 XEON series CPUs.
  • Supports 4-channel 2400MHz DDR4 ECC memory with maximum capacity of 384GB, including up to 64GB per slot.
  • Supports VGA display.
  • Supports up to 4 2.5Gbps networks.
  • Supports 2 M.2 interfaces (NVME only).
  • Supports 9 USB ports and 1 TYPE-E port.
  • Supports 2 PCIE X16 slots and 1 PCIE X8 slot.
  • Supports 10 SATA 3.0 ports.
  • Built-in 6 RS232 and RS485 serial ports.
  • Supports wide temperature operation from -10 to 60 degrees Celsius.
  • Built-in CMOS reset button for faster troubleshooting and issue resolution.
  • 6-layer PCB design ensures more stable performance.
Diagram illustrating six core advantages of the motherboard
Figure 1: Six Core Advantages of the Motherboard. These include Strong configuration, Rich interface design, Aluminum shell, Fully enclosed design, Metal grid heat dissipation, and 24/7 operation.

2. Safety Guidance

Essential Safety Guidelines for Use

  1. Before using this product, please read the product instructions carefully.
  2. For boards not prepared for installation, they should be stored in anti-static protective bags.
  3. Before removing the circuit board from the anti-static protective bag, hands should be placed on a grounded metal object for a period of time (e.g., 10 seconds) to discharge static electricity from the body and hands.
  4. When handling circuit boards, it is necessary to wear electrostatic protective gloves and develop the habit of only touching the edges of the boards.
  5. To prevent electric shock or product damage, always disconnect the AC power supply before removing, inserting, or reconfiguring circuit boards.
  6. Before moving the circuit board or the entire device, the AC power supply must be turned off first.
  7. When adding or removing circuit boards for complete machine products, always disconnect the AC power supply first.
  8. Before connecting or disconnecting any device, you must first turn off the AC power supply.
  9. To avoid unnecessary damage to the product caused by frequent power cycles, wait at least 30 seconds after power-off before restarting.

3. Setup and Installation

3.1 Mainboard Layout Diagrams

Refer to the following diagrams for the physical layout and dimensions of the motherboard.

Top-down view of the motherboard with labels for key components
Figure 2: Mainboard Top View. This image shows the CPU socket, DDR4 DIMM slots, PCIe slots, M.2 slots, SATA ports, and various headers.
Mainboard front view with rear I/O panel details
Figure 3: Mainboard Front View and Rear I/O Panel. This image provides an overview of the motherboard's front side and a detailed view of the rear input/output ports.
Bottom view of the motherboard
Figure 4: Mainboard Bottom View. This image displays the underside of the motherboard.
Close-up of the motherboard's rear I/O ports
Figure 5: Rear I/O Ports. This image details the VGA, LAN, USB, and audio ports available on the back panel.

3.2 Security Note for Installation

  • Before installation, do not arbitrarily remove the serial number or authorized dealer warranty label from the motherboard, as this may affect the warranty period determination criteria.
  • Before installing or removing the motherboard and other hardware devices, make sure to turn off the power supply and unplug the power cord from the socket.
  • When installing other hardware devices into the sockets on the motherboard, ensure the connectors and sockets are securely fastened.
  • When handling the motherboard, avoid touching the metal wiring parts to prevent short circuits.
  • When handling the motherboard, central processing unit (CPU), or memory modules, it is advisable to wear an anti-static wristband. If no anti-static wristband is available, ensure both hands are dry and touch a metal object first to discharge static electricity.
  • Before installing the motherboard, place it in an anti-static mat or bag.
  • When unplugging the power connector from the motherboard, ensure the power supply is turned off.
  • Before powering on, ensure the voltage setting of the power supply matches the standard voltage for your window.
  • Before powering on, ensure all hardware devices have their wiring harnesses and power cords connected correctly.
  • Do not let screws come into contact with the motherboard's wiring or components to prevent damage or malfunction.
  • Ensure there are no loose screws or metal parts on the motherboard or inside the computer case.
  • Do not place the computer on an unstable surface.
  • Do not place the computer case in an environment with excessively high temperatures.
  • Turning on the power supply during installation may cause damage to the motherboard, other devices, or even your own body.
  • If you are unfamiliar with the installation process or encounter any technical issues while using this product, please consult a professional technician.

3.3 Memory Installation

The motherboard features six 288-pin DDR4 DIMM memory slots.

Before starting memory installation, note the following information:

  1. First, ensure the memory you purchased matches the specifications supported by this motherboard.
  2. Before installing or removing memory, ensure the computer's power is off to avoid damage.
  3. The memory design includes anti-mistake markings. If you insert it in the wrong direction, the memory will not be inserted. Change the insertion direction immediately.

Installation Steps:

  1. Before installing or removing memory, first turn off the power supply and unplug the AC power cord.
  2. Hold the memory module firmly at both ends and avoid touching the metal contacts.
  3. Align the gold fingers of the memory module with the slot, ensuring the concave portion of the gold fingers aligns with the convex protrusion of the slot.
  4. Insert the memory module at a 90-degree angle into the slot, then press it down until you hear a "click" sound, indicating successful installation and readiness for use. (Note: Do not apply excessive pressure to avoid damaging the memory module.)
  5. To remove the memory module, push the latches on both ends of the DIMM slot outward simultaneously, then remove the module.

3.4 Jump Cable Settings

Jumpers are used to configure various settings on the motherboard. The following explains how to connect jumpers and identify pin positions.

2 Pin connection: Insert the jumper cap between the two pins to close the circuit (short circuit).

3 Pin connection: The jumper cap can be inserted into pin 1-2 or pin 2-3 to close the circuit (short circuit).

Diagrams showing 2-pin and 3-pin jumper settings
Figure 6: Jumper Settings. This diagram illustrates how to configure 2-pin and 3-pin jumpers for short-circuiting.

How to identify the first step position of a jumper?

  1. Carefully inspect the motherboard. Any pin marked with "1" or a thick white line indicates the 1-pin position.
  2. When inspecting the backplane's solder pads, the square-shaped pad typically serves as the first contact point.

4. Interface Descriptions and Operation

4.1 Audio Interface: F_audio

The motherboard features a 2x5-pin front audio interface with a pin pitch of 2.54mm. The pin configuration is as follows:

Pin Definition Pin Definition
1MIC2_L_S2Mic-in_R
3MIC2_R_S4NC
5LINE2_R_S6MIC-Detect
7FRONT_IO_SENSE8NC
9LINE2_L_S10Line-Detect

4.2 Serial Ports: COM1~COM6

The motherboard features two built-in serial ports with a pin pitch of 2.54mm. It also includes a 4-in-1 built-in serial port (pin pitch 2.00mm), combining four standard RS232 pins into a single pin interface. COM1-COM6 supports RS232 and RS485 transmission modes. Users can configure the transmission mode for COM1-COM6 using pins JP4 through JP9.

COM1-COM2 Definition:

Pin Definition Pin Definition
1DCD2RXD
3TXD4DTR
5GND6DSR
7RTS8CTS
9RI10NC

COM3-COM6 Definition:

Pin Definition Pin Definition
1MDCD32MSIN3
3MS034MDTR3
5GND6MDSR3
7MRTS38MCTS3
9XRI310NC
11MDCD412MSIN4
13MS0414MDTR4
15GND16MDSR4
17MRTS418MCTS4
19XRI420NC
21MDCD522MSIN5
23MS0524MDTR5
25GND26MDSR5
27MRTS528MCTS5
29XRI530NC
31MDCD632MSIN6
33MS0634MDTR6
35GND36MDSR6
37MRTS638MCTS6
39XRI640NC

JP4, JP5, JP6, JP7, JP8, JP9 Settings:

The jump cap (JP4-JP8) is used to configure the transmission modes for COM1-COM6, supporting both RS232 and RS485 protocols. You can customize the settings according to your requirements, with RS232 as the default mode.

Jumper Setting Definition
JP4 (COM1)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern
JP5 (COM2)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern
JP6 (COM3)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern
JP7 (COM4)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern
JP8 (COM5)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern
JP9 (COM6)1-2 Short circuitRS232 pattern
2-3 Short circuitRS485 pattern

JRS485_12, JRS485_34, JRS485_56 Settings:

JRS485_12, JRS485_34, and JRS485_56 pins are used to connect the RS485 data signal transmission between COM1 and COM6.

Pin Definition Pin Definition
1GND25V
3TXDN_14TXDP_1
5TXDN_26TXDP_2
Pin Definition Pin Definition
1GND25V
3TXDN_34TXDP_3
5TXDN_46TXDP_4

JP50 Settings:

The JP50 jumper cap is used to configure the energized function of Pin 9 on COM1 and COM2.

Pin Definition
1-2 Short circuitRS232 pattern (COM1)
3-4 Short circuit5V
5-6 Short circuit12V
7-8 Short circuitRS232 pattern (COM2)
9-10 Short circuit5V
11-12 Short circuit12V

4.3 Printer Interface: LPT Definition

Pin Definition Pin Definition
1R_STB2R_AFD-
3R_PD04R_ERR-
5R_PD16R_INIT-
7R_PD28R_SLIN-
9R_PD310GND
11R_PD412GND
13R_PD514GND
15R_PD616GND
17R_PD718GND
19R_ACK-20GND
21R_BUSY22GND
23R_PE24GND
25R_SLCT26GND

4.4 Switch Interface: JFP Definition

Pin Definition Pin Definition
1HDD_LED+2PWR_LED+
3HDD_LED-4PWR_LED-
5GND6PW_ON
7RST8GND
9GND10NC

4.5 Fan Interfaces: CPU FAN, SYS FAN Definition

The motherboard features 8 heat dissipation fan interfaces (pin pitch: 2.54mm). The pin definitions are as follows:

CPU FAN:

Pin Definition
1GND
2+12V
3TACH-IN
4PWM

SYS FAN:

Pin Definition
1GND
2+12V
3TACH-IN

JCPU MOS3/MOS4:

Pin Definition
15V
2GND

4.6 USB Interfaces: FUSB1 and FUSB3 Definitions

The motherboard features one 2x5-pin USB 2.0 port and one 2x10-pin USB 3.0 port. Pin definitions are as follows:

FUSB1 (USB 2.0):

Pin Definition Pin Definition
1VCC2VCC
3D-4D-
5D+6D+
7GND8GND
9NC10GND

FUSB3 (USB 3.0):

Pin Definition Pin Definition
1VBUS11D+
2SSRX1-12D-
3SSRX1+13GND
4GND14SSTX2+
5SSTX1-15SSTX2-
6SSTX1+16GND
7GND17SSRX2+
8D-18SSRX2-
9D+19VBUS
10NC20NC

4.7 Power-on Jumper: JAT

The motherboard features one 1x3-pin JAT connector (pin pitch: 2.54mm), with pin definitions as follows:

Pin Definition
1-2 (short circuit)Power on
2-3 (short circuit) DefaultATX pattern

4.8 USB Voltage Setting: JP1

The motherboard features one 1x3-pin USB power pin (pin pitch: 2.54mm). Pin definitions are as follows:

Pin Definition
1-2 (short circuit) DefaultUSB3_PWR
2-3 (short circuit)+5VSB

4.9 Case Open Setting: COPEN

The motherboard features one 1x2-pin Case Open connector (pin pitch: 2.54mm). Pin definitions are as follows:

Pin Definition
1Case open
2GND

4.10 Trusted Platform Module: TPM

The motherboard features one 2x7-pin TPM socket (pin pitch: 2.00mm), with pin definitions as follows:

Pin Definition Pin Definition
1TPM_CLK23.3VSB
3PLTRST_PCIE_SLOTS_N43.3V
5LAD06SER_IRQ
7LAD185V
9LAD210NC
11LAD312GND
13LFRAME#14GND

4.11 Network Indicator Lights: LAN_LED1, LAN_LED2

LAN_LED1:

Pin Definition Pin Definition
1LAN2_LEDO_ACT23.3V
3LAN2_LINK1000#43.3V
5LAN1_LEDO_ACT63.3V
7LAN1_LINK1000#83.3V
9/10NC

LAN_LED2:

Pin Definition Pin Definition
1LAN2_LEDO_ACT23.3V
3LAN2_LINK1000#43.3V
5LAN4_LEDO_ACT63.3V
7LAN4_LINK1000#83.3V
9/10NC

5. Maintenance

  • Keep the motherboard clean and free from dust. Use compressed air to regularly clean dust from components, especially heatsinks and fan blades.
  • Ensure proper airflow within your PC case to prevent overheating, which can degrade component lifespan.
  • Periodically check all cable connections (power, SATA, fan headers) to ensure they are secure.
  • Avoid exposing the motherboard to extreme temperatures or humidity.
  • When handling the motherboard, always use anti-static precautions to prevent electrostatic discharge (ESD) damage.

6. Troubleshooting

  • No Power/No Display: Double-check all power connections (24-pin ATX, 8-pin ATX, CPU fan). Ensure the monitor is connected and powered on.
  • System Instability/Crashes: Verify memory installation (ensure modules are seated correctly). Check CPU and GPU temperatures.
  • CMOS Reset: The motherboard includes a built-in CMOS reset button for faster troubleshooting and issue resolution. If you encounter boot issues or incorrect settings, try resetting the CMOS. Refer to the motherboard layout diagram for its location.
  • Peripheral Detection Issues: Ensure all connected devices (SATA drives, USB devices) are properly connected and powered. Check relevant jumper settings if applicable.
  • Network Connectivity Problems: Verify LAN cable connection and check network indicator lights (LAN_LED1, LAN_LED2) for activity. Ensure network drivers are installed correctly.

7. Specifications

Feature Detail
Mainboard Size245mm * 245mm
Central Processing UnitSupports LGA2011 XEON series CPUs (Intel Xeon W Series)
Chipset ManufacturerIntel
ChipsetC612
Internal Storage6 x 288-Pin DDR4 DIMM Memory Slots, up to 64GB per slot (Max 384GB)
Support Memory TypeDDR4
Expansion Slots2 x PCIE X16 slots, 1 x PCIE X8 slot, 2 x M.2 SSD (NVMe only)
PCI - E StandardsPCI-E 2.0
Number of PCI2
Backplane I/O Ports1 x VGA display interface, 2 x USB3.0, 2 x USB2.0, 4 x RJ45 ports, 2 audio interfaces (Line Out/MIC-IN)
Onboard LAN4 x Intel I226V 2.5G network card
Storage Interface TypeSATA 2, M.2 (NVMe)
Built-in Interfaces10 x SATA ports, 1 x 9-pin front panel switch pin (FPANEL), 1 x 4-pin CPU cooling fan (CFAN1), 3 x 4-pin system cooling fan (SFAN1), 2 x 3-pin system cooling fan (SFAN1), 2 x 2-pin System Cooling Fan (SFAN1), 6 x built-in COM interfaces, 1 x LPT interface, 1 x FUSB front-side interface (convertible to 2 USB 2.0 ports), 1 x FUSB front-side interface (convertible to 2 USB 3.0 ports), 1 USB port (convertible to 1 USB 2.0 port), 1 x TYPE-E interface, 1 TPM interface, 1 x 9-pin built-in audio interface (F_audio), 1 x 8-pin ATX port, 1 x 24-pin ATX port, 2 x 9Pin LAN LED, 1 x 2-pin case open
Audio FrequencyRealtek ALC897, supports Line-Out & Line-In
I/O SlugITE IT8786E-I
Supply Electricity24-pin + 8-pin ATX power supply
Operating SystemWindows 10/Windows 11/Linux
Usage ScenarioEnthusiast & Overclocking, Gaming, Audio & Video, Household, Office, Video Production, Industrial Computer, Workstation, Server, Mining, Scientific Computing, 3-D Modeling, Video Rendering, MaxCompute, others
ApplicationDesktop, Server, Workstation, Mining, Industrial Computer
RAID SupportedNo
With CPUNo
Battery IncludedNo
OriginMainland China

8. User Tips

  • This motherboard is highly versatile, suitable for various applications including NAS setups, soft routers, network appliances, and general-purpose PCs.
  • The board supports a high memory capacity, with users successfully installing up to 192GB (e.g., 6 x 32GB modules).
  • The M.2 slot is strategically placed to allow for the installation of large heatsinks on M.2 SSDs, even with a CPU cooler installed.
  • The motherboard is compatible with modern expansion cards, such as WIFI7 PCI-E Wireless LAN cards.

9. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for any warranty claims.

10. Product Overview Video

Video 1: Product Overview. This video provides a visual tour of the motherboard, showcasing its various components and features from different angles.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.