1. Introduction
This manual provides detailed instructions for the installation, configuration, and operation of your KuWFi AC1200 Outdoor Dual Band WiFi 5 Access Point (Model AP1301). This device is designed to provide reliable, high-speed wireless coverage in outdoor and semi-open environments, supporting multiple operation modes including AP, Router, Repeater, WISP, and Mesh.

Image: KuWFi AC1200 Outdoor AP Router, illustrating its dual-band WiFi 5 capabilities.
2. Package Contents
Please check the package carefully for the following items:
- 1x AP1301 Wireless AP Router
- 1x PoE Power Adapter
- 1x Ethernet Cable
- 1x User Manual

Image: Contents of the product package, including the AP1301, PoE adapter, Ethernet cable, and user manual.
3. Product Overview
3.1. Device Components
The KuWFi AP1301 features a cylindrical design with external antennas and essential ports for connectivity and power.
- 2.4G+5.8G Dual Band Antennas (x2): Detachable omnidirectional antennas for dual-band wireless communication.
- Status LEDs: Indicators for device status, network activity, and Wi-Fi bands.
- Pair Button/Reset: A multi-function button for initiating Mesh pairing or restoring factory settings.
- WAN/LAN Port (PoE): A single Ethernet port that functions as either WAN or LAN depending on the operating mode, and supports Power over Ethernet (PoE) for power supply.

Image: Close-up view of the AP1301, highlighting LED indicators, Reset button, and WAN/LAN port.
3.2. Status LED Description
The device's LEDs provide visual feedback on its operational status:
| LED Indicator | Status | Description |
|---|---|---|
| Power | ON | Device is powered on |
| OFF | Device is not receiving electrical power | |
| SYS | ON | Device system has started |
| OFF | Device system not started | |
| LAN/WAN | ON | Ethernet port is connected |
| OFF | Ethernet port not connected | |
| 2.4G WIFI | ON | Device 2.4G Wi-Fi has started |
| OFF | Device 2.4G Wi-Fi not started | |
| 5G WIFI | ON | Device 5G Wi-Fi has started |
| OFF | Device 5G Wi-Fi not started | |
| Link (Mesh Master) | Fast Blinking | No internet |
| Slow Blinking | No internet / Device in pairing state | |
| Solid on | Device connected to internet | |
| Fast Blinking (AP Mode) | No internet | |
| Solid on (AP Mode) | Device connected to the Internet |
4. Setup
4.1. Equipment Assembly
- Attach Antennas: Install the two dual-band antennas onto the RF-SMA interfaces on the device.
- Install Waterproof Ring: Place the RF-SMA waterproof ring onto the RF-SMA connector.
- Connect RJ45 Cable: Connect your Ethernet (RJ45) cable to the RJ45 Port on the device.
- Route Cable through Holder: Pass the RJ45 cable through the cable holder.
- Route Cable through Rubber Seal: Pass the RJ45 cable through the rubber seal.
- Route Cable through Spiral Cover: Pass the RJ45 cable through the spiral cover and secure it.
4.2. Equipment Installation
4.2.1. Pole Mounting
Place the assembled AP unit in front of the desired pole. Use two stainless steel ties to secure the device by running them through the fixing bits of the bracket and around the pole.4.2.2. Wall Mounting
- Mark Drill Holes: Use a ruler to measure the dimensions of the fixed base. Mark the positions for two holes on the wall.
- Drill Holes: Drill holes at the marked spots using a hand drill.
- Insert Plugs: Tap the retaining plugs into the drilled holes with a hammer.
- Install Screws: Screw the mounting screws into the plugs, leaving some space for the device bracket to hang.
- Mount Device: Align the fixing holes of the device bracket with the screws on the wall and press down to secure the device.
4.3. Equipment Connection
4.3.1. Non-standard PoE Power Supply (using power adapter)
- Connect the WAN/LAN port of the AP to the