EWIND EW-S1726CFU-AP

Contents

EWIND AI Smart 24-Port PoE Switch User Manual

Model: EW-S1726CFU-AP

1. Introduction

The EWIND AI Smart 24-Port PoE Switch (Model EW-S1726CFU-AP) is an unmanaged Power over Ethernet (PoE) switch designed for efficient network deployment. It features 24 10/100Mbps PoE ports, 2 Gigabit RJ45 uplink ports, and 1 Gigabit SFP fiber slot. This switch supports IEEE 802.3af/at standards, providing up to 30W per PoE port with a total power budget of 300W. Key features include AI Watchdog for network self-healing, one-key VLAN for port isolation, and an extend mode for long-distance transmission up to 300 meters. This manual provides detailed instructions for setting up, operating, maintaining, and troubleshooting your PoE switch.

2. Package Contents

Please check the package contents carefully. If any item is missing or damaged, contact your vendor.

Package Contents and Dimensions

Figure 2.1: Product Dimensions and Packing List

Table 2.1: Packing List
ContentQTYUNIT
24 Ports PoE with 2*Giga RJ45 and 1*GF SFP (EW-S1726CFU-AP)1SET
Hanging Ear1PAIR
User Guide1PC
Warranty Card1PC

3. Product Overview

The EWIND AI Smart 24-Port PoE Switch is designed for robust and reliable network connectivity. It features a durable metal casing and a fanless design for quiet operation.

3.1 Front Panel

Front and Rear Panel Overview

Figure 3.1: Front and Rear Panel Overview

  • 24 x 10/100 Mbps PoE Ports (1-24): These ports support Power over Ethernet (PoE) for connecting devices like IP cameras, wireless access points, etc. They are compliant with IEEE 802.3af/at standards.
  • 2 x 10/100/1000 Mbps Uplink RJ-45 Ports (25-26): These are Gigabit Ethernet ports for connecting to your network backbone, NVR, or router.
  • 1 x 100/1000 Mbps Uplink SFP Port (27): This Gigabit SFP slot is for fiber optic connections, extending network reach over longer distances. (SFP module not included).
  • LED Indicators: Display power status, link/activity for each port, and PoE status.
  • Dial Code Switch (Extend & VLAN): Allows selection of operating modes.

3.2 Rear Panel

Rear Panel View

Figure 3.2: Rear Panel View

  • AC Power Input: Connect the provided power cord here. The switch has a built-in 200W power supply and accepts AC 100-240V (50/60Hz).

4. Setup and Installation

The EWIND AI Smart 24-Port PoE Switch is designed for plug-and-play operation, requiring no complex configuration.

4.1 Basic Connection

Plug and Play Setup Steps

Figure 4.1: Plug and Play Setup

  1. Connect to Power: Plug the AC power cord into the switch's power input and then into a standard electrical outlet.
  2. Connect Devices:
    • For PoE-powered devices (e.g., IP cameras, wireless APs), connect them to any of the 24 PoE ports (1-24) using standard Ethernet cables (Cat5e/6 recommended). The switch will automatically detect and power these devices.
    • For non-PoE devices (e.g., PCs, NVRs without PoE), connect them to the uplink RJ45 ports (25-26).
    • For fiber optic connections, insert a compatible SFP module (not included) into the SFP slot (27) and connect your fiber cable.
  3. Enjoy: Your network devices should now be connected and operational.

4.2 Rack Mounting (Optional)

The switch is rack-mountable. Attach the provided hanging ears to the sides of the switch using screws, then secure the switch into a standard 19-inch rack cabinet.

5. Operating Modes

The EWIND AI Smart 24-Port PoE Switch offers flexible operating modes controlled by a dial code switch on the front panel.

5.1 Default Mode (AI Watchdog)

By default, the switch operates with the AI Watchdog function enabled on ports 1-24. This feature automatically detects and attempts to resolve issues with connected PoE devices (e.g., IP cameras freezing) by power-cycling the port, reducing the need for manual intervention and after-sales service.

5.2 Extend Mode (E)

Extend Mode and Lightning Protection

Figure 5.1: Extend Mode Details

When the 'E' switch is turned ON, ports 1-4 (or specified ports depending on model variant) will operate in Extend Mode. This mode allows PoE transmission and data communication up to 300 meters at a reduced speed of 10Mbps, ideal for long-distance surveillance deployments.

5.3 VLAN Mode (V)

One Key VLAN Diagram

Figure 5.2: One-Key VLAN Function

When the 'V' switch is turned ON, ports 1-24 are isolated from each other, preventing direct communication between them. However, all isolated ports can still communicate with the uplink ports (25-27). This enhances network security and can improve network performance by reducing broadcast storms in specific scenarios.

6. Maintenance

The EWIND AI Smart 24-Port PoE Switch is designed for minimal maintenance.

  • Cleaning: Use a soft, dry cloth to clean the exterior of the switch. Do not use liquid or aerosol cleaners.
  • Environment: Ensure the switch is operated within its specified temperature and humidity ranges (Operating Temp: -20°C to +55°C; Humidity: 5%~90% RH non-condensing). The fanless design allows for quiet operation and reduces dust ingress.
  • Ventilation: Although fanless, ensure adequate airflow around the device to prevent heat buildup. Do not block ventilation slots.
  • Firmware: As an unmanaged switch, firmware updates are typically not required or available for end-users.

7. Troubleshooting

If you encounter issues with your PoE switch, try the following steps:

  • No Power: Check if the power cord is securely connected to both the switch and the power outlet. Verify the power outlet is functional.
  • No Link/Activity on a Port:
    • Ensure the Ethernet cable is properly connected at both ends.
    • Check the status of the connected device.
    • Try a different Ethernet cable or port.
  • PoE Device Not Powering On:
    • Verify the PoE device is IEEE 802.3af/at compliant.
    • Check the power requirements of the device; ensure it does not exceed 30W per port or the total power budget of 300W.
    • If AI Watchdog is enabled, the switch may attempt to self-heal by power cycling the port.
  • Network Performance Issues:
    • If VLAN mode is enabled, ensure your network topology accounts for port isolation.
    • If Extend mode is used, remember that the speed is reduced to 10Mbps.
    • Check for faulty cables or devices.
  • Lightning Protection: The switch features 4KV lightning protection. In areas prone to lightning, consider additional surge protection for connected devices and power lines.

8. Specifications

Detailed technical specifications for the EWIND AI Smart 24-Port PoE Switch.

Detailed Specifications Table

Figure 8.1: Detailed Product Specifications

Table 8.1: Technical Specifications
ParameterDescription
FanNon-Fan, silent working status can satisfy more users with different requirements.
Network ProtocolIEEE802.3 10BASE-T; IEEE802.3i 10BASE-T; IEEE802.3u 100BASE-TX/FX; IEEE802.3ab 1000BASE-T; IEEE802.3z 1000BASE-X; IEEE802.3x.
PoE StandardIEEE802.3af/at
Ethernet Port10/100BASE-T(X) 10/100/1000BASE-T automatic detection, full/half Duplex MDI/MDI-X adaptive
Fiber Port FeatureGigabit SFP Port (Fiber module is not included, need to order separately, module options include single/multi-mode, single/dual fiber, LC)
Store and ForwardYes
Switching Capacity10.8Gbps (non-blocking)
Forwarding Mode8.05Mpps
MAC Address Table8K
Buffer Memory4M
Twisted Pair Transmission10BASE-T: Cat5 UTP (≤300 meter); 100BASE-TX: Cat5 or later UTP (≤100 meter); 1000BASE-T: Cat5 or later UTP (≤100 meter)
Power Supply PinDefault 1/2(+), 3/6(-)
MAX / AVERAGE Power Per Port30W / 15.4W
Total PWR / Input Voltage300W (100-240V)
Power ConsumptionStandby:<5W; Full load:<300W
LED IndicatorPower indicator: PWR (Green); Network indicator: 1-24(Link/Act) (Green), 25-27(Link/Act) (Green)
Power SupplyBuilt-in switching power supply, AC100~240V 50-60Hz 4.1A
Operation TEMP / Humidity-20°C~+55°C; 5%~90% RH non condensing
Storage TEMP / Humidity-40°C~+75°C; 5%~95% RH non condensing
Dimension310*205*44mm
Net / Gross Weight<2.5kg / <3kg
Installation Methoddesktop type, wall mounted, 19-inch 1U cabinet installation
ProtectionIEC61000-4-2(ESD): ±8kV contact discharge, ±15kV air discharge; IEC61000-4-5(Lightning protection/Surge): Power:CM±4kV/DM±2kV; Port: ±4kV
Protection LevelIP30
CertificationCCC; CE mark, commercial; CE/LVD EN60950; FCC Part 15 Class B; RoHS
Warranty1 year, lifetime maintenance.

9. User Tips

  • For optimal performance, use high-quality Cat5e or Cat6 Ethernet cables, especially for PoE devices and long runs.
  • When using Extend Mode, be aware of the reduced bandwidth (10Mbps) and ensure it meets the requirements of your connected devices (e.g., lower resolution cameras).
  • Utilize the VLAN function to segment your network for improved security and to manage broadcast traffic effectively, especially in larger deployments.
  • The AI Watchdog feature is designed to enhance reliability; however, regular checks of your PoE devices are still recommended.

10. Warranty and Support

The EWIND AI Smart 24-Port PoE Switch comes with a 1-year warranty and lifetime maintenance. For detailed warranty terms, technical support, or further assistance, please refer to the official user manual PDF or contact your vendor.

Additional Resources: A comprehensive user manual in PDF format is available for download. You can access it via this link: EWIND AI Smart 24-Port PoE Switch User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.