VaneAims 16mm Metal Rotary Selector Switch Knob

Contents

VaneAims 16mm Metal Rotary Selector Switch Knob User Manual

Model: 16mm Metal Rotary Selector Switch Knob

1. Introduction

This manual provides comprehensive instructions for the safe and effective installation, operation, and maintenance of your VaneAims 16mm Metal Rotary Selector Switch Knob. Please read this manual thoroughly before use and retain it for future reference.

VaneAims 16mm Metal Rotary Selector Switch Knob
Figure 1: VaneAims 16mm Metal Rotary Selector Switch Knob (Top and Side View)

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the product.

  • WARNING: Disconnect the power supply before wiring or performing any installation/removal procedures. Failure to do so may result in electric shock or damage.
  • The EU LVD Voltage for this device is below 50Vac or 75Vdc.
  • This product contains no high-concerned chemicals.

3. Product Overview

The VaneAims 16mm Metal Rotary Selector Switch Knob is a durable and versatile switch designed for various industrial electrical applications. It features a brass chrome plating housing, PBT base material, and is available in 2-position or 3-position configurations with momentary or latching functions. Options include models with or without LED illumination in various colors and voltages.

Detailed design of the rotary switch components
Figure 2: Detailed Design of the Rotary Switch (Knob, Welding Pin, Metal Shell)

4. Installation

4.1. Installation Steps

  1. Power Off: Before installation or removal, ensure the power supply is completely turned off.
  2. Mounting: Insert the switch into the panel cutout and secure it with a nut from the back.
  3. Wiring: Connect the load according to the wiring diagram provided in Section 4.3.

4.2. Product Dimensions

The switch is designed for a 16mm cutout. Detailed dimensions are provided below:

Product dimension diagram for 16mm cutout, showing no-light and with-light versions
Figure 3: Product Dimension (No Light - 16mm Cutout, With Light - 16mm Cutout)
  • Mounting Diameter: 16mm
  • Cutout: 1.6cm (0.63in)
  • Overall Length: 3.71cm (1.46in)
  • Max Width: 1cm (0.394in)

4.3. Wiring Diagram

Refer to the following diagrams for correct wiring. Ensure the power supply is disconnected before making any connections.

Wiring Diagram showing two plans for connecting the rotary switch with a load and power
Figure 4: Wiring Diagram

Plan A: Basic Operation

In Plan A, when the switch is pressed, the LED light turns on, and the connected load is activated. This configuration is suitable for applications where the LED indicates the active state of the load.

Plan B: Always-On LED with Switch Function

In Plan B, the LED remains lit when powered on, and the switch connects to the Normally Open (NO) contact. This is useful for applications where the LED acts as a constant indicator, and the switch controls a separate function.

4.4. Pin Positions

The switch offers multiple pin positions depending on the configuration (with or without LED, and 1NO1NC or 2NO2NC).

Diagram illustrating multiple pin positions (1NO1NC/2NO2NC) and their pin counts for LED and non-LED versions
Figure 5: Multiple Pin Positions Available
  • 1NO1NC without lamp: 3 pins
  • 1NO1NC with lamp: 5 pins
  • 2NO2NC without lamp: 6 pins
  • 2NO2NC with lamp: 8 pins

5. Operation

The rotary selector switch knob is available in two main functional types: Momentary and Latching, and with 2 or 3 positions.

  • Function: Latching/Momentary
  • LED Color Options: Red, Green, Blue, White (depending on model)
  • LED Voltage Options: 3-6V, 12-24V (depending on model)

5.1. Position Selection

  • 2 Position: Indicates a simple start or close function, where the order of operation is typically OFF → ON.
  • 3 Position: Allows for left and right selection, with an order of operation such as ON → OFF ← ON.

5.2. Operation Demonstration

Watch this video for a visual demonstration of the switch's operation and LED illumination:

Video 1: Product demonstration showing the switch's operation and LED illumination.

6. Specifications

Below are the detailed technical specifications and performance characteristics of the VaneAims Metal Rotary Selector Switch Knob.

FeatureSpecification
Product NameKnob Switch / Key Knob Switch
Mounting Diameter16mm / 19mm / 22mm
Housing MaterialBrass chrome plating / Stainless steel (for some models)
Base MaterialPBT
Position2 or 3 position
Switch Combination1NO1NC or 2NO2NC
FunctionLatching / Momentary
LED OptionNo LED / Red / Green / Blue Ring LED
Voltage3-6V / 12-24V
Pin DefinitionNO/NC/C
Switch TypeKnob switch
Is Smart DeviceNo
OriginMainland China
CertificationCE (EN61058-1:2002+A2:2008, EN60947-1:2004)
Contact Resistance< 50mΩ
Insulation Strength≥ 1000MΩ
Highest Withstand Voltage1500V, AC50HZ, 1 Minute
Vibration Resistance50HZ, Amplitude approx. 1.2mm
Impact ResistanceBigger than 10g
Solder Heat ResistanceAt 320°C (or 30 watt soldering iron) no more than 2 seconds
Electrical LifeMore than 50,000,000 times
Mechanical LifeSelector switch: 500,000 times / Key switch: 200,000 times
Nut TorqueApprox. 0.8Nm
Protection GradeIP65, IK02
Working Temperature-25℃ to +55℃ (no freezing)
Working Environment Humidity45-85%RH (no condensation)

7. Maintenance

To ensure the longevity and optimal performance of your rotary selector switch, follow these general maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the exterior of the switch. Avoid using abrasive cleaners or solvents that could damage the finish or internal components.
  • Inspection: Periodically check for any loose connections, damaged wiring, or signs of wear and tear. Address any issues promptly.
  • Environmental Conditions: Ensure the switch is operated within its specified working temperature and humidity ranges to prevent malfunction.

8. Troubleshooting

If you encounter issues with your rotary selector switch, consider the following common troubleshooting steps:

  • No Power/LED Not Lighting Up:
    1. Verify that the power supply is correctly connected and providing the specified voltage (e.g., 3-6V or 12-24V for LED models).
    2. Check all wiring connections against the wiring diagram (Figure 4) to ensure they are secure and correct.
    3. Inspect the LED for any visible damage.
  • Switch Not Actuating Load:
    1. Ensure the switch is correctly wired to the load according to the wiring diagram.
    2. For latching switches, confirm it is in the correct position. For momentary switches, ensure it is being held long enough.
    3. Check the load itself to ensure it is functioning correctly.
  • Intermittent Operation:
    1. Inspect for loose wiring connections at the switch terminals or the load.
    2. Ensure the switch is securely mounted and not experiencing excessive vibration.

If problems persist after performing these checks, please contact customer support.

9. Warranty and Support

For detailed warranty information, please refer to the official product documentation. A user manual in PDF format is available for download, which may contain additional guides and documents. You can view the user manual PDF here.

For technical support or inquiries, please contact VaneAims PV one-stop Store using the following information:

  • Email: info-mi@vaneaims.com
  • Mobile/WeChat/Skype: +86 15058777695
  • Address: zone, Yueqing, Zhejiang, China.
  • Website: www.vaneaims.com

© 2024 VaneAims. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.