IKSLED 10T/13T/16T Touch Sensor

Contents

User Manual: IKSLED 10/13/16mm Dimmable Touch Sensor Button Smart Home Switch Controller

Brand: IKSLED

Model: 10T/13T/16T Touch Sensor

1. Product Overview

The IKSLED Mini Touch Sensor (10T/13T/16T) is a low-voltage DC touch dimmer designed for intuitive lighting control. It features both one-touch control for on/off functionality and a long-press dimming function, allowing for smooth brightness adjustments. This versatile switch is suitable for a wide range of applications, including cabinet lighting, wardrobe lighting, car interior lighting, and various DIY lighting projects. Its easy installation and user-friendly operation make it an ideal solution for modern low-voltage lighting control needs.

Image showing three sizes of touch sensors (10mm, 13mm, 16mm) in black and white, with an example of installation into a wooden surface.
Figure 1: Available touch sensor sizes (10mm, 13mm, 16mm) and an example of flush installation.

2. Specifications

Parameter Specification
Product Name Touch Dimmer Switch
Model 10T / 13T / 16T (Touch sensor)
Material PC
Operating Voltage DC 3.7V / 5V / 12V / 24V (Wide Voltage Compatible)
Max. Load 2.5A (DC)
Mounting Hole Size 10T: 10mm, 13T: 13mm, 16T: 16mm
Function Tap: On/Off Switch Control; Long Press: Stepless Dimming
Wire Color Red (+), Black (-), Yellow (Load)
Color Options Black / White
High-concerned chemical None
Origin Mainland China

3. Setup and Installation

3.1 Drilling Requirement

Ensure the mounting hole edge is smooth and burr-free to prevent damage to the sensor during installation. The required hole sizes are 10mm for 10T models, 13mm for 13T models, and 16mm for 16T models.

Diagram showing the dimensions of a 16T Black touch sensor, indicating a 16mm punch hole requirement.
Figure 2: Example dimensions for a 16T sensor, showing a 16mm punch hole.

3.2 Wiring Diagram

The sensor comes with three wires for connection:

  • Red (+): Connect to DC Power Positive.
  • Black (-): Connect to DC Power Negative.
  • Yellow (Load): Connect to the positive terminal of your LED strip or light fixture.
Close-up image of the touch sensor wires, clearly labeled LED-, LED+, Power+, Power-.
Figure 3: Detailed view of the wiring connections.

3.3 Installation Steps

  1. Prepare the Hole: Ensure the drilled hole is smooth and burr-free, matching the sensor's size (10mm, 13mm, or 16mm).
  2. Insert Sensor: From the back of the mounting hole, push the sensor through until its clip secures tightly against the panel.
  3. Secure Sensor: Confirm the sensor is firmly attached to the panel without any looseness.
  4. Connect Wiring: Follow the wiring diagram above to connect the Red, Black, and Yellow wires to your power supply and LED load.
  5. Test Functionality: Apply power and test the on/off and dimming functions.
Image showing a touch sensor connected to an LED strip light, demonstrating a typical application.
Figure 4: Example of the touch sensor connected to an LED strip light.

4. Operating Instructions

  1. Toggle Power (On/Off Control): Lightly tap the power logo area on the sensor panel to switch the connected load (e.g., LED light) on or off.
  2. Adjust Brightness (Stepless Dimming): When the light is on, press and hold your finger on the power logo area. The brightness will change smoothly (either dimming or brightening). Release your finger when the desired brightness level is reached to lock it in place.
Video 1: Demonstration of installing the touch sensor and controlling an LED strip light, showing both on/off and dimming functions.

5. Maintenance

To ensure optimal performance and longevity of your touch sensor, please observe the following:

  • Install the sensor in a dry, well-ventilated environment.
  • Avoid exposing the sensor to water immersion or high temperatures.
  • Keep the sensor surface clean and free from debris that might interfere with touch detection.

6. Troubleshooting

Fault / Symptom Possible Cause Solution
No response / Touch not working
  • Power disconnected
  • Polarity reversed
  • Load open circuit
  • Check power connection
  • Recheck wiring polarity
  • Inspect load circuit
Flickering / Unable to dim
  • Excessive load power
  • Unstable voltage
  • Reduce load to within 2.5A
  • Use stable DC power supply
Overheating / Sensor getting hot
  • Overload operation
  • Poor ventilation
  • Reduce load current
  • Improve heat dissipation

7. Safety Warnings

  • Power Supply: This product is designed for DC power supply ONLY. Connecting to AC power is strictly prohibited and will cause damage.
  • Max Load: Do not exceed the maximum load of 2.5A to prevent overheating and potential damage to the sensor or connected devices.
  • Wiring: Always disconnect power before performing any wiring to prevent short circuits.
  • Polarity: Do not reverse the positive and negative poles during wiring, as this will cause product damage.

8. User Tips

  • Ensure the correct voltage (3.7V / 5V / 12V / 24V DC) is used for your application.
  • Double-check all wiring connections before applying power to avoid issues.
  • For best dimming performance, use with compatible LED strip lights or low-voltage lighting modules.
  • Users generally find the touch control responsive and effective for both on/off and dimming functions.

9. Warranty and Support

For detailed information, including additional diagrams and specifications, please refer to the official user manual PDF:

View User Manual (PDF)

For further assistance or inquiries, you may contact the manufacturer at: nina@iksled.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.