JIANKEXING 2023524m

Contents

JIANKEXING Italian Living Room Floor Lamp User Manual

Model: 2023524m

1. Introduction

Thank you for choosing the JIANKEXING Italian Living Room Floor Lamp. This manual provides essential information for the safe assembly, operation, and maintenance of your new lamp. Please read these instructions carefully before installation and retain them for future reference.

1.1. General Safety Precautions

  • Install the lamp strictly according to instructions. Do not modify the lamp at will, as this may create unsafe conditions, including falling hazards or electrical leakage.
  • For safe use, it is recommended to entrust installation, inspection, and maintenance to qualified professionals.
  • Do not use the lamp in wet or high-temperature environments, such as bathrooms.
  • This lamp is not dimmable. Do not connect it to a dimming controller to avoid malfunction.
  • In case of any abnormality (e.g., flickering, unusual smells), immediately cut off the power supply.
  • Always ensure the power is off before performing any maintenance or bulb replacement.

2. Package Contents

Carefully unpack the box and ensure all parts are present. If any parts are missing or damaged, do not attempt to assemble the lamp and contact your retailer.

  • Lamp Base
  • Lamp Pole Sections
  • Lamp Shade (Acrylic)
  • Lamp Holder (E27)
  • Power Cord with Button Switch
  • Accessories Package (containing necessary fasteners)

Note: Light bulbs are not included and must be purchased separately.

3. Assembly Instructions

This product requires assembly. While specific, model-detailed assembly instructions for this floor lamp were not provided in the available documentation, general steps for floor lamp assembly should be followed. Always ensure the lamp is unplugged during assembly.

  1. Prepare the Area: Choose a clear, flat surface to assemble your lamp.
  2. Assemble the Base: Attach the lowest pole section to the lamp base. Ensure it is securely tightened.
  3. Connect Pole Sections: Carefully thread the power cord through each pole section as you connect them, screwing each section together until the full height of the lamp pole is achieved. Ensure all connections are firm.
  4. Attach Lamp Holder: Secure the lamp holder to the top of the assembled pole.
  5. Install Lamp Shade: Carefully place the acrylic lamp shade onto the lamp holder. Secure it in place according to its design (e.g., with a retaining ring).
  6. Insert Bulb: Screw an E27 LED bulb (not included) into the lamp holder. Do not overtighten.
  7. Final Check: Ensure all connections are secure and the lamp is stable before plugging it into a power outlet.

Warning: Do not connect the lamp to power until fully assembled and stable.

4. Operation

Your JIANKEXING floor lamp is designed for simple operation.

  1. Connect to Power: Plug the lamp's power cord into a standard 90-260V AC electrical outlet.
  2. Turn On/Off: Locate the button switch on the power cord. Press the button once to turn the lamp on, and press it again to turn the lamp off.
  3. Light Color (if applicable): If your lamp model is specified as "3-colors", repeated presses of the button switch may cycle through different light temperatures (e.g., warm, neutral, cold). For models specified with a single light color (e.g., "warm light", "cold light", "neutral light"), the lamp will emit that fixed color when turned on.

5. Maintenance

5.1. Cleaning

  • Always turn off the lamp and unplug it from the power outlet before cleaning.
  • Allow the lamp to cool down completely if it has been in use.
  • Gently wipe the lamp body and acrylic shade with a clean, dry, soft cloth.
  • Do not use abrasive cleaners, solvents, or any liquids that could damage the finish or electrical components.
  • Do not immerse any part of the lamp in water or any cleaning solution.

5.2. Bulb Replacement

  • Ensure the lamp is turned off and unplugged from the power outlet.
  • Allow the bulb to cool down completely before touching it.
  • Unscrew the old E27 LED bulb counter-clockwise.
  • Screw in a new E27 LED bulb clockwise until snug. Do not overtighten.
  • Only use LED bulbs of appropriate wattage (11-15W recommended) and voltage (90-260V).

6. Troubleshooting

ProblemPossible CauseSolution
Lamp does not turn on
  • Lamp not plugged in
  • Power outlet not working
  • Bulb is loose or burnt out
  • Switch malfunction
  • Ensure lamp is securely plugged into a working outlet.
  • Test the outlet with another device.
  • Tighten or replace the E27 LED bulb.
  • Contact customer support if the switch is faulty.
Light flickers
  • Loose bulb
  • Incorrect bulb type/wattage
  • Unstable power supply
  • Tighten the bulb.
  • Ensure you are using an E27 LED bulb within the 11-15W range.
  • Check the power supply; try a different outlet.

7. Specifications

FeatureDetail
BrandJIANKEXING
Model Number2023524m
Item TypeFloor Lamp
StyleModern Style, Nordic
Installation MethodAssembly
Power SourceAC
Voltage90 - 260 V
Light SourceLED bulbs (not included)
Base TypeE27
Wattage11-15W
Number of Light Sources1
Luminous Flux2000-82000 (depending on bulb)
Is DimmableNo
Switch TypeBUTTON SWITCH
Body MaterialPVC
Shade MaterialAcryl, ABS
FinishPlated, Polished Chrome
Shade DirectionUp & Down
Lighting Area10-15 square meters
ApplicationFoyer, Living Room, Bedroom, Study
CertificationsRoHS, CE
OriginMainland China
Package Dimensions (approx.)125 cm (L) x 58 cm (W) x 58 cm (H)
Package Weight (approx.)10.0 kg

7.1. Product Dimensions

Floor Lamp Version (D50 H166CM)

Dimensions of the D50 H166CM floor lamp

Height: 166 cm
Diameter: 50 cm
Lighting Area: 10-20 m²

Table Lamp Version (D30 H70CM)

Dimensions of the D30 H70CM table lamp

Height: 70 cm
Diameter: 30 cm
Lighting Area: 8-10 m²

8. User Tips

To maximize your experience with the JIANKEXING floor lamp:

  • Choose an LED bulb with a color temperature that best suits your room's ambiance (e.g., warm white for cozy spaces, cool white for task lighting).
  • Position the lamp in a corner or next to a sofa to provide ambient or accent lighting, enhancing the room's design.

9. Warranty and Support

This JIANKEXING floor lamp comes with a 2-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, warranty claims, or any questions regarding your product, please contact the seller or your point of purchase. Provide your model number (2023524m) and a detailed description of the issue to facilitate faster service.

For further documentation, you may refer to the official user manual PDF: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.