1. Introduction
The Radtel RM-06 is a 50W Dual Band Mobile Radio designed for amateur ham radio enthusiasts. It features Bluetooth connectivity, GPS, Compass, and a Built-in Speedometer, offering a premium communication experience. The device supports easy programming via a smartphone application.
This manual provides detailed instructions for the safe and efficient operation of your RM-06 radio. Please read it thoroughly before use and keep it for future reference.
2. Safety & General Information
FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety Information for Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.
Important FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF exposure guidelines when used with accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna. Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC regulations.
Normal Position: Hold the transmitter approximately 25 mm from your face and speak in a normal voice, with the antenna pointed up and away.
Waste Disposal: All articles displaying the symbol of a crossed-out wheeled bin on the body, packaging or instruction manual must not be thrown away into normal disposal bins but brought to specialized waste disposal centers. Here, the various materials will be divided by characteristics and recycled, thus making an important contribution to environmental protection.
Compliance with RF Exposure Standards
This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material.
Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection.
Local Government Regulations
When two-way radios are used as a consequence of employment, the Local Government Regulations requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Radtel two-way radio has an RF Exposure Product Label. Also, your Radtel user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements.
Radio License
Governments classify radios, and most classified walkie-talkies require a local government license for operation. For detailed classification and use of your radio, please contact your local government radio management department.
CE Marking
The CE marking means: Hereby, Xiamen Radtel Electronics Co.,Ltd declares that the radio equipment type is in compliance with the RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available in this manual or at the following internet address: www.radtel.com
General Safety Precautions
- Do not operate the equipment without the battery pack installed or while installing/removing it. Always use the ON/OFF control.
- Install the battery pack and accessories correctly, according to the instructions.
- Never transmit with a damaged antenna.
- Avoid transmitting for extended periods.
- Do not touch the antenna or any part of the body when the equipment is transmitting.
- In case of malfunction (burnt scent, smoke), turn off the transceiver immediately or disconnect the battery charger from the AC outlet and consult Technical Service.
- Do not introduce any object into the speaker holes or transceiver connectors. If using an external headset, reduce volume to the lowest possible level to avoid very high audio.
- Do not expose the equipment or battery charger directly to water, direct sunlight for extended periods, heat sources (radiators), excessive dust or dirt, fire, explosive or dangerous conditions. Do not store the transceiver inside a vehicle parked in sunlight.
- Avoid humidity condensation. If condensation occurs, clean with a dry cloth and allow to dry completely before use.
- Do not place anything on the transceiver that can spill.
- If the transceiver causes interference with video recorders, DVDs, radios, or televisions, move it away from the affected apparatus.
- Do not use this transceiver near other electronic equipment, especially medical equipment, as it can cause interference.
- Turn off and do not use the equipment in areas where its use is restricted or prohibited (e.g., coal gas areas, explosion atmospheres, areas where it can interfere with other equipment, on board airships, airports, etc.).
- Do not operate this transceiver while driving a vehicle; use hands-free systems ("VOX" function) and respect traffic police indications.
- To clean the equipment and/or battery charger, turn it OFF and use an antistatic cloth (preferably) or a humid (not wet) cloth.
- Do not spray any liquid or product directly on the transceiver, battery pack, or charger. Never use polish, home products, detergents, alcohol, or solvent for cleaning.
- Do not use a dry cloth for cleaning, as it could cause static shock.
- Using incompatible accessories can limit transceiver operation and invalidate the guarantee.
- Risk of explosion if the battery pack is replaced with an incompatible one.
3. Familiar with Radio
Overview of Components
The Radtel RM-06 consists of the main radio unit and a handheld speaker microphone. Key components include:
- Antenna: For signal transmission and reception.
- PTT (Push-To-Talk): Button to initiate transmission.
- Side-keys 1 & 2: Programmable function keys.
- Battery: Power source for the radio.
- SW/MW/LW FM antenna (Channel knob): For specific radio frequencies and channel selection.
- ON/OFF volume: To power on/off and adjust audio level.
- Indicator Light: Shows operational status (e.g., transmitting, receiving, charging).
- Alarm Button: For emergency alerts or custom functions.
- Display screen: LCD for showing frequency, channel, and status.
- Keypad: For numeric input and menu navigation.
- MIC: Microphone for voice input.
- Speaker: For audio output.
- Ear/Mic jack: For external audio accessories.
- Type C charging port/programmable jack: For charging and programming.
Top View Components
- Antenna Port 1: Used for all frequency transmission and reception except short wave/middle wave/long wave/FM radio frequencies.
- Antenna Port 2: Used for short wave/middle wave/long wave/FM radio frequencies.
- Power Button/Volume Adjustment: Used to turn the device on/off and adjust the volume.
- Emergency Alarm Button/Customizable Button: Can be used for emergency alarms or customized functions.
- LED Light:
- Green Light: Indicates the device is receiving a signal.
- Red Light: Indicates the device is transmitting a signal.
LCD Display Symbols & Indicators
The LCD display provides visual feedback on the radio's status and settings. Key indicators include:
- Keyboard Lock
- Prompt Tone
- Scan
- RR: Talk around/TR: Reverse Frequency
- Multi-Frequency Standby
- VOX (Voice Operated Transmit)
- GPS (option function)
- Cross-Band Repeater
- Battery Icon
- Multi-PTT Enable
- Received Signal Strength
- Received Signal Field Strength Value
- High Power / Low Power switchable
- CTCSS / DCS / MUT Non-standard DCS / ENC Encrypted DCS
- Wide or Narrow Bandwidth
- FM/AM RX
- CH-XXXX: channel number in channel mode / ZONE-XXX: zone number in zone mode
- Working Frequency / Working Channel
- Main Frequency Area Indicator Icon
- Channel Name
- Working Frequency Range
- A/B/C Main Frequency Area
- Received Signal Meter
4. Setup
Charging Radio
Your two-way radio supports three charging methods:
- Charging with the Radio in the Charging Dock:
- Insert the battery into the radio.
- Place the radio into the charging dock.
- Ensure the radio is properly seated in the charger.
- Charging the Battery Alone in the Charging Dock:
- Remove the battery from the radio.
- Insert the battery into the charging dock.
- Make sure the battery is aligned correctly.
- Charging via USB-C Cable:
- Plug a USB-C cable into the charging port on the side of the radio.
- Connect the other end of the cable to a power adapter, computer, or power bank.
LED Indicator Status during Charging:
- Red Light: Charging in progress.
- Green Light: Charging complete.
Note: Use only the recommended charger and cables. Do not charge in extreme temperatures. Fully charge the battery before first use for optimal performance. Do not use cell phone fast chargers to charge this radio.
5. Operation
Keypad Function
| Keys | FUNCTION |
|---|---|
| PTT | Transmit or Exit |
| Alert Key | Definable long press (L) and short press (S) functions |
| Side Key1 | You can select the [Multi-PTT Switch] option in the menu to use it as PTT-2 for transmission, which will disable the custom function. Definable long press and short press functions. |
| Side Key2 | You can select the [Multi-PTT Switch] option in the menu to use it as PTT-3 for transmission, which will disable the custom function. Definable long press and short press functions. |
| Menu/OK | Short press to confirm or enter into menu |
| Up Arrow | Move up; long press to quickly scroll up. DTMF :B |
| Down Arrow | Move down; long press to quickly scroll down. DTMF :C |
| Exit/Cancel | Short press: Switch ABC channels, exit the menu, and cancel the operation. DTMF :C |
| 0 | Short press: Enter the number 0. Long press to definable functions, or switch scanning direction in FM RADIO mode. DTMF :0. To input Number 0 or Space Bar. |
| 1 | Short press: Enter the number 1. Long press to definable functions. DTMF :1. To input Number 1/English Letters/Chinese Characters. |
| 2-9 | Short press to input Number 2-9. Long press to definable functions. DTMF :2-9. To input Number2-9/English Letters/Chinese Pinyin Codes. |
| * | Short press to switch from channel frequency /channel number/channel Alias, Move the cursor in FM RADIO mode. Long press to lock the keypad. DTMF :*. Text input: Delete text. |
| # | Short press: Switch the working mode to VFO frequency mode/channel mode/zone mode. Or switch short wave modulation in FM RADIO. Long press: Jump to the transmit frequency input menu. Or switch short wave mode in FM RADIO. DTMF :#. Text input: Enable or disable text input, switch text input method. |
Basic Operation
5.1 Set Working Frequency
The device operates in three frequency ranges: 64-620 MHz, 18-64 MHz, and 840-1000 MHz. Transmission and reception for all three bands are handled via the left main antenna port.
To change the frequency band, navigate to [Basic Settings] → [17 Work Range] in the menu. After selecting the desired frequency band and confirming, the device will restart.
Important: Ensure that you replace the antenna with one that matches the selected frequency band. Using an incorrect antenna may result in damage due to frequency mismatch.
5.2 Frequency Input
- Switch to VFO Frequency Mode: Press the # key to enter VFO Frequency Mode.
- Enter the Frequency: Use the numeric keypad to input the desired frequency. The input must be either 6 digits or 8 digits, depending on the selected setting.
- Frequency Input Settings: Navigate to [Basic Settings] → [Freq Input 30]. Select [6 Bits] to allow 6-digit frequency input. Select [8 Bits] to require 8-digit frequency input.
5.3 Repeater Frequency Input
Method 1: Using Offset Frequency Settings
- Navigate to [CH Settings] → [16 Offset Freq] and use the numeric keypad to input the offset frequency.
- Go to [CH Settings] → [15 Offset Direction] and select either positive or negative offset.
Method 2: Direct Transmit Frequency Input
- In standby mode, long press the [#V/M] key to enter the [Transmit Frequency] menu.
- Use the numeric keypad to enter the desired transmit frequency, then press OK to confirm. The device will return to the previous menu.
- Go to [CH Settings] to access the sub-audio settings menu and configure the sub-audio frequency as needed.
5.4 Transmitting Signals
Standard Transmission: Press the PTT key to initiate a call on the current frequency. The LED indicator will turn red during transmission.
Multi-PTT Mode (If enabled in [Key Definition] → [1 Multi-PTT]): When Multi-PTT Mode is active, the shortcut functions of Side Key 1 and Side Key 2 are disabled. Side Key 1 transmits on Band B, and Side Key 2 transmits on Band C.
5.5 Receiving Signals
When the device receives a signal on the same frequency, the LED indicator will turn green. Audio output will be enabled if:
- No sub-audio (CTC/DCS) is set, or
- The received sub-audio matches the configured sub-audio on the device.
5.6 CTC/DCS Settings
Navigate to [CH Settings] to set the sub tone CTCSS or DCS.
- CTC/DCS (Transmit & Receive): Enables both transmit and receive CTC/DCS. The device will only communicate with signals that match the set code.
- RX CTC/DCS (Receive Only): The device will only accept signals that match the set CTC/DCS code, but transmission remains unrestricted.
- TX CTC/DCS (Transmit Only): The device will transmit using the set CTC/DCS code, but it will receive all incoming signals without restriction.
5.7 U/V Cross-Band Repeater
Activating Cross-Band Repeater Mode: Assign a button to [26 UV Repeater] for quick activation. Alternatively, enable it via [Basic Settings] → [28 UV Repeater].
Once activated:
- Channel C is disabled.
- Only Channels A and B are used for cross-band repeating.
- Signals received on Channel A are retransmitted on Channel B.
- Signals received on Channel B are retransmitted on Channel A.
Monitoring Repeater Audio: Enable [29 Repeater Monitor] in [Basic Settings] to listen to repeater voice communications.
5.8 DTMF Function
DTMF Encoding Input & Transmission:
- Accessing DTMF Input Mode: In standby mode, long press the Menu/OK key to enter the DTMF input interface.
- Entering DTMF Codes: Use the numeric keypad to input the DTMF codes. Short press Side Key 2 to delete the last entered digit.
- Transmitting DTMF Codes: Press the PTT key to initiate a call. The device will send the DTMF code after a preset delay.
DTMF Decoding: When the device receives a signal and DTMF decoding is enabled, the received DTMF code will be displayed on the screen.
DTMF Transmission in Analog Mode: During analog transmission, pressing a key on the keypad will send the corresponding DTMF code.
DTMF Remote Monitoring:
- Set a DTMF monitoring code for the device and enable [Accept Remote Control].
- Another radio can send the same DTMF code to this device.
- Upon receiving and successfully decoding the DTMF code, the device will automatically transmit for 60 seconds, enabling remote monitoring.
DTMF Remote Stun/Kill/Wake:
- Setting Remote Control Codes: Set the DTMF remote stun/kill/wake code for the device and enable [Accept Remote Control].
- Sending Remote Commands: Another radio can send the corresponding DTMF code to remotely stun, kill, or wake the device.
- Device Behavior:
- Stunned: The device cannot transmit or operate the keypad but can still receive signals.
- Killed: The device becomes inoperable until it receives a wake code.
- Important Warning: Ensure a wake code is set before enabling stun/kill functionality, as the device cannot be restored once stunned or killed without a wake code.
5.9 Text Input Function
- In the Text Input Menu:
- # key: Switch between different input methods.
- * key: Delete text or pinyin.
- Number Input [123]: Use the numeric keypad to enter numbers.
- English Input [AB] / [abc]:
- Keys 2-9: Input corresponding letters.
- 0 key: Inputs a space.
- 1 key: Inputs symbols.
- Press a key multiple times to cycle through the letters (e.g., pressing 2 will display A, B, C sequentially).
- Chinese Pinyin Input [PY1] / [PY2]:
- PY1: Common Chinese characters.
- PY2: A more extensive character set, including rare and traditional characters.
Enter pinyin using the numeric keypad, use Up/Down arrow keys to select characters, and press the Menu/OK key to confirm.
5.10 FM Radio (activate MW/SW/LW Short wave radio receiver)
- Defining the FM Radio Trigger: Go to the menu, then Key Define to assign a button for the FM Radio function. Pressing the defined button will enter radio mode. Pressing the PTT key will exit radio mode.
- Switching Between Radio Bands: Long press the # key to switch between radio bands:
- USW (Ultra Short Wave: 64-108 MHz)
- SW (Short Wave: 2.0-30.0 MHz)
- MW (Medium Wave: 520-1710 KHz)
- LW (Long Wave: 153-279 KHz)
- Switching Demodulation Modes: Short press the # key to switch the radio's demodulation mode. The USW band is fixed to FM (Frequency Modulation), which cannot be changed. Other bands can switch between: AM (Amplitude Modulation), USB (Upper Sideband), LSB (Lower Sideband), CW (Continuous Wave, Morse Code).
- * Key Short Press: Switches the Input Type. When the frequency symbol is pointing to the radio frequency, you can manually enter a frequency value to change the frequency. When entering other types of data, press the Up/Down arrow keys to switch the data content. For example, channel numbers can be directly input to switch to the corresponding channel.
- * Key Long Press: Enter Scan Mode. Press any key to exit scan mode. When the radio is not in scan mode, long press the 0 key to switch the scan direction.
- Single Sideband (USB/LSB) Demodulation: If you encounter sharp sound, lower the BFO (Beat Frequency Oscillator) frequency. If the sound is too deep, increase the BFO frequency.
5.11 One-Key Frequency Measurement & Remote Sub-Audio CTCSS/DCS Decoding
- After pressing the trigger button, the device enters Frequency Measurement or Remote Sub-Audio Decoding Mode and starts scanning surrounding RF signals.
- Press the * key to switch between Frequency Measurement Mode and Remote Sub-Audio Decoding Mode.
- During frequency measurement: Press the PTT key or exit key to exit. Press the # key to switch the frequency band.
- After completing frequency measurement: Press the exit key to re-measure. Press the menu key to save the measurement result to the VFO channel and return to VFO standby mode. Press the PTT key to transmit.
5.12 Spectrum Scanning Mode
- Press the trigger button to enter Spectrum Scanning Mode. Press the * key to exit.
- Short press the * key to switch input fields. The spectrum display interface includes three input items:
- Scan Center Frequency (top-left): Adjusting this moves the scan center point.
- SPACE: Scan step size (frequency interval between adjacent waveforms), unit: kHz.
- DECAY: Signal amplitude attenuation, lowering the overall spectrum height for clearer observation of the main signal and adjacent channels.
- Press Up/Down arrow keys to move the indicator cursor. The bottom display will update to show: Frequency at the cursor position, RSSI (Received Signal Strength Indicator), NOISE (Signal noise intensity), GLITCH (Spurious signal strength).
Menu List
The radio features an extensive menu system for configuration. Below are key menu items and their functions:
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| 1 | Name/Callsign | customize | Set the name or callsign of the walkie-talkie. |
| 2 | Voice Prompt | Off/On | Turn on/off the voice prompt. |
| 3 | Key Beep | Off/On | Turn on/off the key beep. |
| 4 | Lock Timer | Off/5s~600s | Set the lock time (5 seconds to 600 seconds). |
| 5 | Key LED Timer | Off/On | Turn on/off the key LED indicator. |
| 6 | LCD Timer | Off/5s~600s | Set the timed-off time for the LCD display (5 to 600 seconds). |
| 7 | Brightness | 0~4 | Adjust the brightness of the LCD display (0 to 4). |
| 8 | Menu Exit | Off/5s~600s | Set the timed-off time for menu exit (5 to 600 seconds). |
| 9 | TX Priority | Edit / Busy | You can edit the transmit priority. Busy indicates that the current transmitter is busy. |
| 10 | Freq Step | 0.25K/1.25K~5M | Set the size of the frequency step. You can choose from 0.25K, 1.25K to 5M. |
| 11 | Talkaround | Off/Talk around/Invert Freq | Talkaround mode allows direct communication on the same frequency without using a repeater, enhancing simplicity and reducing reliance on infrastructure for communication. |
| 12 | Save Mode | Off/1:1/1:2/1:3 | Turn off the save mode. Save the one-to-one/Two/Three mode. |
| 13 | Scan Mode | CO/TO/SE | Channel/Time/Search scan. |
| 14 | Scan Direction | Up/Down | Scan upwards/Scan downwards. |
| 15 | Scan Return | Original CH / Current CH | Return to the original channel or current channel after scan. |
| 16 | Alarm Type | Local Alarm / Remote Alarm / Local+Remote | Set local, remote, or both types of alarms. |
| 17 | Work Range | 64-620MHz / 18-64MHz / 840-1000MHz | Set the frequency range. |
| 18 | Area A Mode | Freq Mode / CH Mode / Zone Mode | Set the Channel mode, Frequency model or zone mode. |
| 19 | Area A Show | Show CH No / Show Freq | Set the display way in the selected mode. |
| 20 | Area A Zone | Zone-001~256 | Set the zone numbers. |
| 21 | Area B Mode | Freq Mode / CH Mode / Zone Mode | Set the Channel mode, Frequency model or zone mode. |
| 22 | Area B Show | Show CH No / Show Freq | Set the display way in the selected mode. |
| 23 | Area B Zone | Zone-001~256 | Set the zone numbers. |
| 24 | Area C Mode | Freq Mode / CH Mode / Zone Mode | Set the Channel mode, Frequency model or zone mode. |
| 25 | Area C Show | Show CH No / Show Freq | Set the display way in the selected mode. |
| 26 | Area C Zone | Zone-001~256 | Set the zone numbers. |
| 27 | Multi Standby | Off/On | The multi-standby mode allows the device to switch between multiple frequencies or signals while remaining in standby status. |
| 28 | UV Repeater | Off/On | Cross band repeater function. |
| 29 | Repeater Monitor | Off/On | Monitor the working status of the repeater in real time including signal strength, connection status, etc. |
| 30 | Freq Input | 6 bits / 8 bits | The device can receive and process signals of different frequencies, with the supported frequency input range being 6 or 8 digits. |
| 32 | Save CH | CH-0001 Y~ / CH-0008 Y~ / CH-1024 N | Save frequently used channels in the device for quick access. |
| 32 | Delete CH | CH-0001 Y~ / CH-0008 Y~ / CH-1024 N | Delete channels that are no longer needed from the device to keep the channel list tidy and orderly. |
| 33 | Version | UV Radio / V1.05 2025 | Show the version information. |
| 34 | Initialization | Cancel / Ensure | Confirm or cancel the Initialization. |
Key Define Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| 1 | Multi PTT | Off/On | Set the side key 1 and side key 2 as the PTT button. If enabled, it will disable the defined button. |
| 2 | Side Key 1S | None / Monit / Power Switch / Scanning / VOX / SQ / Freq Step / Multi Standby / TX Priority / Roger Beep / FM Radio / Talkaround / Alarm / Send Single Tone / Freq Detect / CTC/DCS Scan / Spectrum / Radio Sleep / Query Status / Save CH / RX AM/FM / NOAA CH / LCD On-Off / LCD Brightness / Key LED On-Off / UV Repeater | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 3 | Side Key 1L | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 4 | Side Key 2S | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 5 | Side Key 2L | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 6 | Alarm Key 2S | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 7 | Alarm Key 2L | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 8 | 0 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 9 | 1 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 10 | 2 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 11 | 3 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 12 | 4 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 13 | 5 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 14 | 6 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 15 | 7 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 16 | 8 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
| 17 | 9 Press Long | See above for options. | Set the side key 1, side key 2, Alarm key, Num0-9 short press or long press functions. |
Analog Settings Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| 1 | SQ Level | 0~10 | 0-10 adjustable sensitivity for optimizing reception in varying signal conditions. |
| 2 | TX Start Tone | Off/On | Customizable audio tone when power On. |
| 3 | TX End Tone | Off / Roger Beep 1 / Roger Beep 2 / Send Radio Name | Customizable audio tone at end of transmitting. |
| 4 | Single Tone | 1750Hz | When the radio transmits a 1750 Hz tone, it is generally recognized by the repeater, which will activate and allow the transmission to go through. |
| 5 | VOX On-off | Off/On | Toggleable voice-controlled transmission. |
| 6 | VOX TH | 0~254 | Set vox level. |
| 7 | VOX Delay | 0~5 | Delay time after voice activation. |
| 8 | Detect Range | 18-620MHz / 840-1000MHz | Detects signals within the specified frequency range. |
| 9 | Repeater Delay | 0~2000ms | Delay time for use via repeater. |
| 10 | MIC Gain | 0~31 | Adjusts the microphone gain. |
| 11 | FM Mode SPK Gain | 0~63 | Adjusts the speaker gain in FM mode. |
| 12 | FM Mode DAC Gain | 0~15 | When experiencing sound distortion, lower the volume a bit. |
| 13 | AM Mode SPK Gain | 0~63 | Adjusts the speaker gain in AM mode. |
| 14 | AM Mode DAC Gain | 0~15 | When experiencing sound distortion, lower the volume a bit. |
| 15 | Glitch TH | 0~10 | Adjust the interference threshold. |
| 16 | DTMF Delay | 0~2000ms | Adjusts the delay for DTMF signals. |
| 17 | DTMF Interval | 30~200ms | Sets the interval between DTMF signals. |
| 18 | DTMF Duration | 30~200ms | Sets the duration of DTMF signals. |
| 19 | DTMF Mode | Off / TX Start / TX End | Controls the DTMF mode. |
| 20 | DTMF Select | DTMF-01~16 | Selects the DTMF signal to be used. |
| 21 | DTMF Display | Off/On | Enables or disables the DTMF display. |
| 22 | DTMF TX Gain | 0~127 | Adjusts the transmit gain for DTMF signals. |
| 23 | DTMF RX TH | 0~63 | Sets the receive threshold for DTMF signals. |
| 24 | DTMF Control | Off/On | Controls the DTMF functionality. |
| 25 | Time Calibrate | Off/On | Enables or disables time calibration. |
| 26 | TX Voice Refresh | 0~2000ms | Sets the transmit voice refresh rate. |
| 27 | RX RSSI Refresh | 0~2000ms | Sets the receive RSSI refresh rate. |
| 28 | Temporary Tuning | Off/On / 0~127 / 0~254 | Enables or disables temporary RX setup. Indicates RSSI/noise level. Sets power level. |
CH Settings Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| 1 | CTC/DCS | D023N / D025N~D754N | Transmit & receive CTC/DCS. |
| 2 | RX CTC/DCS | D023N / D025N~D754N | Receive CTC/DCS signals. |
| 3 | TX CTC/DCS | D023N / D025N~D754N | Transmit CTC/DCS signals. |
| 4 | TX Freq | 144.125MHz | Set the transmission frequency. |
| 5 | DCS Encrypt | Standard / Encrypt 1 / Encrypt 2 / Encrypt 3 / Mute Code | Used to select different DCS encryption modes. |
| 6 | Mute Code | 00000000 | Used to set the mute code. |
| 7 | Band Width | Wide/Narrow | Used to select bandwidth (wide or narrow). |
| 8 | Tail Tone | Off/On | Used to turn tail tone on or off. |
| 9 | Scrambler | Off/1~8 | Used to select different voice scrambling modes. |
| 10 | Busy Lock | OFF / Carrier Match / CTC/DCS Match | Used to control the lock state, turn off carrier matching and CTC/DCS matching functions. |
| 11 | TX Power | Low/Medium/High | Set the transmission power, can choose low, medium, or high. |
| 12 | Scan Add | Add/Remove | Add or remove scan channels. |
| 13 | TOT | Off/5~600s | Set the time-out (TOT), can choose to turn off or set the time to 5 to 600 seconds. |
| 14 | CH Alias | Customizes | Customize channel aliases. |
| 15 | Offset Direction | Set the repeater offset direction. | |
| 16 | Offset Freq | Customizes | Customize the offset frequency. |
| 17 | AM/FM RX | AM/FM | Choose to receive AM or FM Modulation signals. |
Zone Settings Menu
| Zone | Second Menu | Description |
|---|---|---|
| Zone-001~256 | Edit Name / Select CH | Set zone name or select channels in this zone. |
FM Radio Menu
| Menu | Second Menu | Description |
|---|---|---|
| RX Standby | Off/On | Switch on/off RX Standby. |
| CH List | CH001-Empty~ / CH128-Empty / Edit Name / Set As Current | Edit Name or Set As Current for channels. |
Time Management Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| 1 | APO | Off/On | Turns the APO (Automatic Power Off) feature on or off. |
| 2 | APO Timer | Customizes | Sets the time interval for the APO feature to turn off the device. |
| 3 | AWU | Off/On | Turns the Automatic Wake-Up (AWU) feature on or off. |
| 4 | AWU Timer | Customizes | Sets the time interval for the AWU feature to wake up the device. |
| 5 | System Time | Customizes | Sets the current time on the device. |
GPS Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| GPS | Off/On | Turn on or off GPS background reception. | |
| GPS Baudrate | Set the baud rate of the GPS module (default 9600). Refer to GPS module specification for corresponding baud rate. | ||
| UTC Zone | Set the time zone of the user's location. | ||
| PC Monitor | Upload GPS data to the PC through the frequency writing serial port. Users can use the serial port monitoring tool to understand the data reported by GPS. | ||
| Coordinate Type | Set the longitude and latitude display format. | ||
| [Speed Unit] | Set the unit used for speed information display. | ||
| [Distance Unit] | Set the unit used for distance information display. | ||
| [Altitude Unit] | Set the unit used for altitude information display. | ||
| [Fixed Latitude] | Set a fixed latitude. | ||
| [Fixed Longitude] | Set a fixed longitude. | ||
| [Fixed Altitude] | Set a fixed altitude. | ||
| [Mileage] | The total mileage of the machine. | ||
| [Mileage Type] | Mileage accumulation method, select Startup Zero (clears mileage count every time the machine is turned on) or Keep (does not clear mileage count). | ||
| [Clear Mileage] | Clear the mileage count. | ||
| [Manual Record] | Manually record the current GPS location information. | ||
| [GPS Auto Record] | Automatically record GPS location information at a scheduled time. | ||
| [GPS Record Time] | The time interval for recording GPS information at a scheduled time. | ||
| [Query Track] | Query GPS manual and automatic records, and dynamically record the position and distance relative to the user's current position, so that users can find the location of the recorded point according to the recorded track. | ||
| [Clear Track] | Clear all recorded tracks. |
APRS Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| APRS | [APRS On-off] | Turn on or off the APRS function. | |
| [Station Mode] | Station type, choose to use dynamic GPS coordinates as the local coordinates or use the preset fixed coordinates under the [GPS] menu as the local coordinates. | ||
| [Beacon Setup] | Beacon settings. | ||
| [Call Sign] | Local call sign. | ||
| [SSID] | SSID. | ||
| [Symbol Table] | APRS symbol set "/" or "\". | ||
| [Symbol] | APRS symbol selection. | ||
| [Comment] | Custom message. | ||
| [MIC-E On-off] | MIC-E compressed data switch. | ||
| [MIC-E Mode] | MIC-E compressed data type. | ||
| [Path 1] | Forwarding path 1. | ||
| [Path 1 Count] | The number of times forwarding path 1 needs to be forwarded. | ||
| [Path 2] | Forwarding path 2. | ||
| [Path 2 Count] | The number of times forwarding path 2 needs to be forwarded. | ||
| [TX Voltage] | Add the local voltage report to the APRS data sent. | ||
| [TX Star Count] | Add the total number of valid satellites found by GPS to the APRS data sent. | ||
| [TX Mileage] | Add the local mileage information to the APRS data sent. | ||
| [Beacon Mode] | Beacon mode. | ||
| [PTT After] | APRS transmission is linked with PTT, and APRS data is sent when PTT transmission is released. | ||
| [Smart Mode] | Smart beacon. Timed beacon, APRS data will be sent once at a certain time. | ||
| [Time Mode] | Timed beacon, APRS data will be sent once at a certain time. | ||
| [Timed Time(S)] | Time interval for sending timed beacons. | ||
| [Queue Mode] | Queue beacon. [Queue Interval] Queue interval. | ||
| [DIGI SETUP] | Digital forwarding settings. | ||
| [DIGI REP CH] | Digital forwarding channel, after receiving APRS data, if the path matches, it will be sent through the selected channel. | ||
| [DIGI1 On] | Digital forwarding 1 switch. If the information in the received APRS data is consistent with the content of DIGI 1 Name, the machine will forward the received APRS data. | ||
| [DIGI1 Name] | Digital forwarding 1 name, used to match whether the received APRS data is forwarded. | ||
| [DIGI2 On] | Digital forwarding 2 switch. If the information in the received APRS data is consistent with the content of DIGI 2 Name, the machine will forward the received APRS data. | ||
| [DIGI2 Name] | Digital forwarding 2 name, used to match whether the received APRS data is forwarded. | ||
| [Wait Before REP] | The waiting time for forwarding the received APRS data, unit: seconds. | ||
| [Remote Password] | Forwarding remote password. | ||
| [APRS RX CH] | APRS only receives and decodes on the set channel. | ||
| [APRS TX CH] | Transmitting channel when triggering APRS transmission. | ||
| [TX Level] | APRS transmission gain level. | ||
| [RX Level] | APRS reception gain level. | ||
| [Demod Tone] | APRS decoding prompt tone. | ||
| [TX Data Upload] | The data sent by APRS is reported to the PC via the frequency writing data line. | ||
| [RX Data Upload] | The data received by APRS is reported to the PC via the frequency writing data line. | ||
| [Beacon Pop-up] | After APRS decoding is successful, the beacon data interface pops up automatically. | ||
| [PTT Priority] | PTT priority, whether to send APRS data or start a call after triggering PTT. | ||
| [PTT Delay] | The delay time for PTT to send APRS. | ||
| [Beacon List] | [Beacon Save] Whether to store the received beacon. The stored beacon record list. | ||
| [Beacon List CLR] | Clear the stored beacon list. | ||
| [APRS Init] | Initialize all APRS related data. |
Denoise Menu
| NO | Menu | Second Menu | Description |
|---|---|---|---|
| Denoise | Off/On | Turn on or off the transmission noise reduction function. |
6. Advanced Operation
Basic Settings (Advanced Details)
- [Lock Timer]: Set the lock time (from 5 seconds to 600 seconds). After locking, press and hold the * key to unlock.
- [Key LED Timer]: Set the key backlight. After selecting "off", the light will go out. After turning it on, the light will remain lit.
- [LCD Timer]: Set the timed-off time for the LCD display (5 seconds to 600 seconds). After selecting "off", the display will remain lit.
- [Brightness]: Set the time for the backlight to automatically turn off. Select [Off] to disable the timer, and the backlight will no longer turn off automatically.
- [Talkaround]: The Talkaround function enables walkie-talkies to communicate directly with each other without relying on a repeater. The Invert Freq function is mainly used to solve the mirror frequency interference problem.
- [Save Mode]: Enabling power-saving mode can conserve battery power, but in this mode, the reception may be slower, and there may be instances of missing characters at the beginning.
- [Scan Mode]: Set up as [CO], the radio will resume scanning once the received signal ends. Set up as [TO], the radio will resume scanning after it receives signal and stay for a while. Set up as [SE], the radio stops scanning once it receives signals.
- [Scan Direction]: This function is used to set the scanning direction of the walkie-talkie within the frequency band.
- [Scan Return]: Select [Original CH] to return to the channel that was active when the scan started after the scan is complete. Select [Current CH] to remain on the channel currently being scanned after the scan ends.
- [Alarm Type]: Select [Local Alarm] to trigger an alarm sound on this device after the alarm is activated. Select [Remote Alarm] to send an alarm signal to the remote radio without any sound on this device. Select [Local + Remote Alarm] to trigger both an alarm sound on this device and send an alarm signal to the remote radio.
- [Work Range]: Switch between the 16-64MHz/64-620MHz/840-1000MHz working frequency bands. After switching, the radio will restart. Please replace the antenna with the corresponding frequency band antenna in time.
- [Multi Standby]: After enabling, the device will simultaneously monitor signals on the A, B, and C frequency bands. However, only one band can be in receiving mode at any given time.
- [U/V Repeater]: Enable or disable the U/V repeater function. When enabled, Channel C will be unavailable.
- [Repeater Monitor]: Monitor the working status of the repeater in real time, including signal strength, connection status, etc.
- [Save CH]: Save frequently used channels in the device for quick access.
- [Delete CH]: Delete channels that are no longer needed from the device to keep the channel list tidy and orderly.
- [Version]: Show the version information.
- [Initialization]: Restore the frequency data of this device to the state of the last frequency programming.
Key Define Functions & Operations
- [Multi PTT]: When enabled, side key 1 will function as PTT-2 to transmit on frequency B. The custom function assigned to side key 1 will be disabled. Side key 2 will function as PTT-3 to transmit on frequency C, and its custom function will be disabled.
- 1.None: No function.
- 2.Monitor: Opens the receiver audio.
- 3.Power Switch: Toggles high/low power.
- 4.Scanning: Initiates scanning (any key to exit).
- 5.VOX (Voice-Activated Transmission): Enables/disables.
- 6.SQ: Adjust squelch settings.
- 7.Freq Step: Set frequency step size.
- 8.Multi Standby: Enable/disable Triple frequency monitoring.
- 9.TX Priority: Switch the Priority Transmission Mode to either "Edit" or "Busy." When set to "Busy," the main frequency band will automatically switch to the last active call frequency after the conversation ends.
- 10.Roger Beep: Switching the Transmit End Tone Type for Analog Channels.
- 11.FM radio: (see description 5.10).
- 12.Talk around: Switching Repeater Channel Frequency to Off-Network or Reverse Mode. In Off-Network Mode, the transmit signal will be sent using the receive frequency. In Reverse Mode, the transmit and receive frequencies are swapped.
- 13.Alarm: After pressing the trigger button, the device will enter Emergency Alarm Mode and emit an alert tone. Press any key to exit.
- 14.Send single tone: After pressing the trigger button, the device will transmit a single-tone signal on the current frequency. Press any key to stop transmission.
- 15.Freq Detect: (see description 5.11).
- 16.CTC/DCS scan: (see description 5.6).
- 17.Spectrum: (see description 5.12).
- 18.Radio sleep: Low Power Sleep Mode. After pressing the trigger button, the device enters low-power sleep mode. It will wake up either when the button is pressed again or when the auto-wake timer reaches the preset duration. Note: The system time is not retained when powered off. To maintain system time while the device is off, use Forced Sleep Mode instead of shutting down.
- 19.Query status: After pressing the trigger button, the device will display the current battery voltage and other status information.
- 20.Save CH: After pressing the trigger button, the device will navigate to the "Save Channel" menu to save the channel data.
- 21.RX AM/FM: Switch the current channel to AM or FM reception modulation mode. The AM mode is typically used for receiving aviation band information.
- 22.NOAA CH: After pressing the trigger button, the device enters NOAA Weather Forecast Scanning Mode. You can switch weather forecast channels using the channel knob. If no operation is performed within 6 seconds, the device will automatically start scanning weather forecast channels.
Below are the 11 NOAA weather forecast frequencies:
- 1: 162.550
- 2: 162.400
- 3: 162.475
- 4: 162.425
- 5: 162.450
- 6: 162.500
- 7: 162.5250
- 8: 161.650
- 9: 161.775
- 10: 161.750
- 11: 162.000
- 23.LCD on-off: To turn on or off the display backlight.
- 24.LCD Brightness: To adjust the display backlight brightness.
- 25.Key LED on-off: To turn on or off the keyboard backlight.
- 26.UV Repeater: Cross-band Repeater. The function of receiving a UHF signal on frequency A and transmitting it through frequency B on the VHF band.
Analog Settings (Advanced Details)
- [SQ Level]: The higher the value, the deeper the squelch, making it harder to open the reception.
- [TX End Tone]: After the transmission is completed, a selected specific tone is emitted to provide feedback to the user, confirming that the communication operation is completed.
- [MIC Gain]: Adjust the microphone sensitivity. The higher the value, the higher the sensitivity.
- [SPK Gain]: Adjust the receiving audio volume. The higher the value, the louder the received audio. To avoid distortion in the received sound, the SPK gain should not be set too high.
- [DTMF Delay]: When initiating a call, the DTMF tone will be transmitted after the set delay time.
- [DTMF Interval]: Set the interval time between two DTMF tones.
- [DTMF Duration]: Set the duration of a single DTMF tone.
- [DTMF Mode]: Used to set the timing of DTMF transmission when initiating a call. When [Off] is selected, the transmission signal will not send a DTMF tone.
- [DTMF Selection]: Select one of the 16 preset DTMF codes to be transmitted when initiating a call.
- [DTMF Display]: When [On] is selected, the received DTMF code will be displayed on the screen.
- [DTMF Tx Gain] and [DTMF RX TH]: Some different-brand radios may experience difficulties decoding DTMF codes. By adjusting these two options, you can maximize compatibility with DTMF codes from different radio brands. It is recommended to set the transmission gain to 64 and the decode threshold to 24.
- [DTMF Control]: When [On] is selected, other radios can control this device by sending the same DTMF code as the listening/stun/kill/wake-up code set on this device.
- [TX Voice Refresh Time]: Changes the refresh interval for the sound pressure bar during transmission.
- [Rx RSSI Refresh]: Changes the refresh interval for the signal strength display. When the signal is weak, if the refresh speed of the signal strength display is too fast, it may introduce interference noise. In such cases, you can increase the refresh time interval to avoid this issue.
- [Temporary tuning]: To adjust the receiving sensitivity, enable [Temporary Receive Threshold Open], then adjust [Temporary RSSI Threshold] and [Temporary Noise Threshold]. The higher the RSSI value, the harder it is to open the reception, and vice versa. Noise behaves oppositely—higher values make it easier to open reception, and lower values make it harder to open. To adjust the transmission power, enable [Temporary Power Open], then adjust the power tuning values for different frequency ranges. When the tuning value exceeds a certain limit (which varies for each device), continuing to adjust may only increase the current without raising the power and could potentially damage the power amplifier or other components. Therefore, it is not recommended to set the tuning value too high. Note: Users who are not familiar with the technical specifications of the radio should avoid using the temporary debugging function, as improper use may cause component damage.
7. Troubleshooting Guide
| Problem | Possible Cause | Solution |
|---|---|---|
| No power on | Battery is dead or not inserted properly | Check battery charge and connection |
| No Transmission | PTT (Push-To-Talk) button not pressed or faulty | Ensure PTT is pressed; check for damage |
| Poor Audio Quality | Weak signal or interference | Move to a clear area; adjust antenna |
| Short Battery Life | Old battery or high power usage | Replace battery; use power-saving mode |
| Cannot Receive Signal | Wrong channel or squelch level set | Verify channel settings; adjust squelch |
| Distorted Sound | Volume too high or speaker clogged | Lower volume; clean speaker grille |
| Overheating | Prolonged transmission or faulty unit | Allow cooldown; check ventilation |
| Stuck in One Channel | Lock feature enabled | Disable channel lock function |
| The radio keeps transmitting | VOX may be turned on or the squelch level is too sensitive | Turn off VOX or adjust squelch level |
Note: If the above solutions can't fix your problems, or you have other inquiries, please contact our technical support by email or live chat.
8. Technical Specifications
| General | |
|---|---|
| Radio | FM 64-108MHz, SW 2.3-30MHz, MW 520-1710KHz, LW 153-279KHz |
| Frequency Range RX | 18-620MHz, 840-1000MHz |
| Frequency Range TX | 18-32MHz, 136-174MHz, 400-520MHz |
| Channel Capacity | 1024 Channels +3*VFO Channels |
| Channel Spacing (W/N) | Analog: 25kHz/12.5kHz, Digital: 12.5K |
| Voltage | 7.4V DC |
| Working Mode | Same frequency simplex, different frequency simplex |
| Antenna | Removable Antenna |
| Frequency Stability | ±2.5ppm |
| Working Temperature | -20°C ~ +60°C |
| Dimension | 149*64*37 about 307g |
| Receiving Part | |
| Modulation Mode | F3E |
| Maximum Frequency deviation (W/N) | ≤5KHz / ≤2.5KHz |
| Output Power (UHF/VHF) | ≤10W |
| TX Current | ≤2500mA |
| Transmitting Part | |
| Sensitivity (W/N) | 0.22μV/0.25μV 12dB SINAD |
| Inter modulation (W/N) | 65dB/60dB |
| Audio Distortion | <5% |
| Audio Output Power | <1W (16Ω) |
| RX Current | ≤350mA |
| Standby current | ≤100mA |
Note: The above specifications may change due to technical improvement without prior notice or liability.
9. User Tips
- For optimal performance, ensure your antenna matches the selected frequency band.
- Utilize the smartphone app for easy programming and firmware updates, especially for advanced features like GPS and APRS.
- When using the cross-band repeater function, remember that Channel C will be disabled.
- Always fully charge the battery before first use to ensure optimal performance and battery longevity.
- If experiencing poor audio quality, check for interference and adjust your antenna or location.
10. Warranty & Support
For technical support, warranty claims, or any inquiries regarding your Radtel RM-06 radio, please contact Radtel customer service. You can find contact information on the official Radtel website: www.radtel.com or via email at support@radtel.com.
Please refer to the full user manual PDF for comprehensive details on warranty terms and conditions. The PDF manual can be accessed at Radtel RM-06 User Manual (PDF).