SLyric 3-in-1 OPT Laser E-light IPL Nd Yag Machine

Contents

SLyric 3-in-1 OPT Laser Hair Removal and Skin Rejuvenation Machine User Manual

Model: 3-in-1 OPT Laser E-light IPL Nd Yag Machine

1. Introduction

Thank you for choosing the SLyric 3-in-1 OPT Laser E-light IPL Nd Yag Machine. This advanced device integrates OPT (Optimal Pulse Technology), E-light (IPL+RF), Nd Yag Laser, and RF (Radio Frequency) technologies to provide a comprehensive solution for various aesthetic treatments. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your device.

Key Functions:

  • Permanent Hair Removal
  • Tattoo Removal
  • Wrinkle Removal
  • Skin Rejuvenation
  • Acne Treatment
  • Vascular Treatment
SLyric 3-in-1 machine with functions listed
Figure 1: SLyric 3-in-1 Machine Overview with Key Functions

2. Package Contents

Please check the package carefully upon arrival to ensure all components are present and undamaged.

  • Main Unit (SLyric 3-in-1 Machine)
  • Diode Laser Handpiece
  • IPL/E-light Handpiece with various filters
  • Nd Yag Laser Handpiece with various tips
  • RF Handpiece
  • Power Cable
  • Protective Eyewear (for operator and client)
  • User Manual (refer to PDF for full details)
SLyric 3-in-1 machine with all accessories
Figure 2: All Included Handpieces and Accessories

3. Setup

  1. Unpacking: Carefully remove the main unit and all accessories from the packaging. Retain the packaging for future transport or storage.
  2. Placement: Place the machine on a stable, flat surface in a well-ventilated area. Ensure there is sufficient space around the machine for proper air circulation.
  3. Power Connection: Connect the power cable to the machine's power inlet and then to a grounded electrical outlet. Ensure the voltage matches your local power supply (110V or 220V, depending on your model).
  4. Handpiece Connection: Identify the ports for each handpiece (RF, OPT, Diode) on the front panel. Carefully align and connect each handpiece to its corresponding port. Ensure they are securely fastened.
  5. Power On: Insert the key into the key switch and turn it to the 'ON' position. Press the red emergency stop button to release it (if it's pressed in). The machine will power on, and the touch screen will display the welcome interface.
Front view of SLyric 3-in-1 machine with welcome screen
Figure 3: Machine Front Panel and Welcome Screen

Video Guide: Initial Power-On and Interface Overview

Video 1: Demonstrates power-on sequence, interface navigation, and basic settings adjustment.

4. Operating Instructions

4.1 Interface Navigation

  1. After powering on, touch the screen to proceed from the welcome screen.
  2. Select the desired applicator: IPL, Diode (808/755/1064nm), or RF.
  3. Once an applicator is selected, you will enter the treatment parameter setting screen.

4.2 Parameter Settings (Diode Laser Example)

The treatment screen allows you to adjust various parameters for optimal results and client safety.

  • Pulse (ms): Adjust the duration of each laser pulse. Higher values generally mean more energy delivered per pulse.
  • Frequency (Hz): Adjust the number of pulses per second. Higher frequency allows for faster treatment.
  • Skin Type: Select the client's skin type (Fitzpatrick scale I-VI) for pre-set recommended parameters. This is crucial for safety and efficacy.
  • Cooling Status: Monitor the handpiece cooling temperature (displayed on screen). Ensure adequate cooling for client comfort and safety.
  • Ready/Standby: Toggle between 'Ready' (active treatment mode) and 'Standby' (paused mode).

4.3 Treatment Procedures

Always perform a patch test before full treatment. Ensure both operator and client wear appropriate protective eyewear.

  1. Client Preparation: Cleanse the treatment area. For hair removal, shave the area prior to treatment. Apply cooling gel if required by the specific treatment.
  2. Handpiece Selection: Attach the appropriate handpiece and select it on the screen. For Nd Yag, ensure the correct tip (e.g., 1064nm for dark tattoos, 532nm for red/orange tattoos) is attached. For IPL, ensure the correct filter is inserted.
  3. Parameter Adjustment: Based on client's skin type, hair color/thickness (for hair removal), tattoo color, or skin condition, adjust the Pulse, Frequency, and other relevant settings. Start with lower settings and gradually increase as tolerated.
  4. Treatment Application: Place the handpiece firmly on the skin. Press the trigger button to emit laser pulses. Move the handpiece evenly across the treatment area.
  5. Post-Treatment: Clean the treated area. Apply soothing gel or cream as needed.
SLyric 3-in-1 machine in use on a client
Figure 4: Machine in Use During a Treatment Session
Close-up of handpieces, filters, and tips
Figure 5: Various Handpieces, Filters, and Tips for Different Treatments

5. Maintenance

  • Cleaning: After each use, clean the handpieces and the machine's surface with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure no gel or debris enters the handpiece apertures.
  • Cooling System: Regularly check the water level in the cooling system (if applicable, refer to the full PDF manual for specific instructions on water refill/change). Use distilled water only.
  • Storage: When not in use, store the machine in a clean, dry, and dust-free environment. Disconnect the power cable.
  • Handpiece Care: Handle handpieces with care. Avoid dropping them or subjecting them to strong impacts.

6. Troubleshooting

If you encounter any issues, please refer to the following common problems and solutions. For more complex issues, contact customer support.

ProblemPossible CauseSolution
Machine does not power onPower cable not connected; Key switch off; Emergency stop button pressedCheck power connection; Turn key switch on; Release emergency stop button
Handpiece not firingHandpiece not securely connected; Machine in 'Standby' mode; Parameters not setReconnect handpiece; Switch to 'Ready' mode; Set treatment parameters
Error message on screenSystem malfunction; Sensor errorRestart the machine; If error persists, contact support
Insufficient coolingLow water level in cooling system; Air circulation blockedCheck and refill water; Ensure proper ventilation around machine

7. Specifications

FeatureDetail
Product Name3 in 1 OPT Laser E-light IPL Nd Yag Hair Removal Machine
Brand NameSLyric
Technology3 in 1 OPL+ND YAG LASR+RF
Laser Module Power4500W
Power TypeElectric
Voltage110V / 220V (selectable via SKU)
Item TypeEpilator
Use AreaARMPIT, Legs/Arms, Body, Face
Package Length31 cm
Package Width32 cm
Package Height33 cm
Package Weight20.0 kg

8. User Tips

  • Always perform a patch test on a small, inconspicuous area of skin before treating a larger area to assess skin reaction.
  • Ensure the skin is clean, dry, and free of lotions, oils, or makeup before treatment.
  • Maintain consistent contact between the handpiece and the skin for effective energy delivery and cooling.
  • Follow recommended post-treatment care, such as applying soothing gels and avoiding direct sun exposure.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your seller directly. Keep your purchase records handy when contacting support.

Additional Resources: A user manual PDF is available for download. Please note that the content of the provided PDF indicates contacting the seller for the full manual. View User Manual (PDF)

© 2023 SLyric. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.