NYXI Hyperion 3

Contents

NYXI Hyperion 3 Wireless JoyPad for Switch 2

User Manual

Thank you for purchasing our product. Before use, please read this manual carefully.

1. Compatibility

The NYXI Hyperion 3 Wireless JoyPad supports the Nintendo Switch 2 host system version 20.0 and above.

2. Package Contents

The package includes the following items:

  • Left controller x1
  • Right controller x1
  • Rechargeable center bridge x1
  • Replaceable D-pad x1
  • USB-C charging cable x1
  • Product user manual (warranty card) x1
Package contents of NYXI Hyperion 3 controllers, center bridge, D-pad, USB-C cable, and manual, with controller dimensions.
Figure 2.1: Package Contents and Controller Dimensions

3. Technical Specifications

3.1 Game Controller

Specification Value
Product ModelNS-202
Product CodeNJ22
MaterialABS
Weight (Left & Right together)215g
Input5V # 500mA
Operating Voltage3.7V
Charging Current400mA
Battery Capacity (Left Controller)600mAh
Battery Capacity (Right Controller)600mAh
Operating Current (Without Motor Vibration)~60mA
Operating Current (With Motor Vibration)~100mA
Dimensions (Left Controller)61.2 * 116.7 * 52.2 mm
Dimensions (Right Controller)61.2 * 116.7 * 52.2 mm

3.2 Center Bridge

Specification Value
MaterialABS
Weight50g
Input5V # 1000mA
Operating Voltage5V
Operating Current800mA
Charging Current (per side)200mA
Dimensions115.6 * 46 * 16 mm

4. Product Overview

Familiarize yourself with the buttons and features of your NYXI Hyperion 3 JoyPads.

4.1 Controller Layout

Detailed diagram of the left controller's buttons and features, including minus button, L button, left joystick, D-Pad, Screenshot button, and T button.
Figure 4.1: Left Controller Layout
Detailed diagram of the right controller's buttons and features, including plus button, R button, BAX Y buttons, right joystick, HOME button, C button, and T button.
Figure 4.2: Right Controller Layout

Key Features:

  • Left Controller: - Button, L Button, Left Joystick, D-Pad, Screenshot Button, T Button, ZR Button, Magnetic Detachment Button, GR Button, SR Button, SYNC Button, SL Button.
  • Right Controller: + Button, R Button, BAX Y Buttons, Right Joystick, HOME Button, C Button, T Button, ZL Button, Magnetic Detachment Button, GL Button, SR Button, SYNC Button, SL Button.
  • Center Bridge: Type-C Charging Port, Left/Right Controller Charging Indicator Light, Left/Right Controller Charging Dock.

4.2 Product Showcase Video

Video 4.1: Visual introduction to the NYXI Hyperion 3 Wireless JoyPad features and design.

5. Setup & Connection

5.1 Wired Connection

To connect the controllers via wired mode:

  1. Align the left controller's '-' key and the right controller's '+' key upwards.
  2. Magnetically attach them to the corresponding magnetic ports on both sides of the Nintendo Switch 2 console.
  3. The console will indicate a successful match with a connection animation on both sides.
Diagram illustrating how to attach the left and right controllers to the sides of the Nintendo Switch 2 console for wired connection.
Figure 5.1: Wired Connection to Switch 2 Console

5.2 Bluetooth Connection

To pair the controllers via Bluetooth:

  1. Power on your Switch 2 console.
  2. On the main interface, tap the controller icon with your finger, then select the "Change Grip/Order" screen.
  3. Press and hold the SYNC button on the left (or right) controller for 3 seconds until the RGB indicator flashes rapidly, entering Bluetooth pairing mode.
  4. The console will automatically search for and pair with the controller.
  5. After successful connection, the controllers' RGB indicators will display solid lights in the following channel colors:
    • Channel 1: Solid Orange
    • Channel 2: Solid Green
    • Channel 3: Solid Blue
    • Channel 4: Solid Purple

5.3 Bluetooth Reconnection

After initial pairing, if the controller is in sleep mode and the console is on, press any button (except L3, R3, TURBO) to reconnect via Bluetooth. Avoid touching the joysticks during reconnection.

5.4 Bluetooth Wake-up

After initial pairing, if both the console and controller are in sleep mode, press the Home button on the right controller to wake up the console and reconnect.

5.5 Keylinker App Connection

The Keylinker App allows for advanced customization of your controllers.

QR code for downloading the Keylinker App.
Figure 5.2: Keylinker App QR Code
  1. Use a mobile browser to scan the QR code or search for "KeyLinker" in your app store to download and install.
  2. After installation, upon first launch, the app may request relevant permissions; grant them as prompted.
  3. Connect your phone's Bluetooth in Android/iOS mode, find the device named "NYXI NJ22", and tap to pair.
  4. After successful connection, tap the settings button next to the device name to enter the controller customization interface.
  5. Within the app, buttons can be remapped, joystick and trigger curves adjusted, motor vibration intensity modified, Turbo function speed set, and macro programming configured. Power-off timing and other settings are also available.
  6. After modifying functions, click "Apply" to save the changes.

6. Operating Instructions

6.1 Turbo Function

The Turbo function allows for rapid-fire input.

  1. Assign Turbo:
    • Left Controller: Hold the Turbo button + UP, DOWN, LEFT, RIGHT, ZL, or L.
    • Right Controller: Hold the Turbo button + A, B, X, Y, ZR, or R.
    Then hold the assigned button to enable rapid-fire. The RGB indicator flash frequency matches the turbo speed.
  2. Auto Turbo: Press and hold the same combination again (Turbo button + direction/button) to set the corresponding buttons to auto turbo mode.
  3. Cancel Turbo: Press and hold the same combination a third time to cancel the turbo function for the corresponding buttons.
  4. Clear All Turbo: Press and hold the left Turbo button (for left controller) or the right Turbo button (for right controller) for 5 seconds. The controller will vibrate for 1 second, indicating all turbo assignments have been cleared.
  5. Turbo Speed Adjustment: There are three adjustable speeds: Fast / Medium / Slow. To increase the turbo frequency, hold Turbo + push the joystick up. To decrease, hold Turbo + push the joystick down. The default speed is Medium. The controller will vibrate briefly each time the turbo speed is adjusted.
Diagram showing how to assign and adjust Turbo function speed using the Turbo button and joystick.
Figure 6.1: Turbo Function Assignment and Speed Adjustment

6.2 Back Button Mapping & Macro Programming

The two customizable buttons GL/GR on the back of the controller can be mapped to specific function keys or programmed as macros.

  • GL can be mapped to: UP, DOWN, LEFT, RIGHT, L, ZL, L3, -.
  • GR can be mapped to: A, B, X, Y, R, ZR, R3, +.

Operation Steps:

  1. While connected to the host, hold the TURBO button and press the GL/GR button once. Release to enter GL/GR button customization mode. The RGB indicator will flash white rapidly, and the controller will vibrate for 1 second.
  2. Press a desired function key (e.g., L button for GL or A button for GR). The lit indicator will flash once, confirming the key has been mapped. Press the GL (or GR) button again to exit customization mode.
  3. Macro Programming: During customization, multiple function keys can be input in sequence for a single GL/GR button. Press the GL/GR button again to exit and save as a macro key. A single custom button can store up to 21 key inputs.
  4. Clearing GL/GR Custom Button Functions: While connected to the host, hold the TURBO button and press the GL/GR button once. Release to enter GL/GR customization mode. Briefly press the GL/GR button to clear the custom functions. A successful clear is indicated by 1 second of vibration.
Diagram showing the process of mapping back buttons (GL/GR) by holding the Turbo button and pressing GL or GR.
Figure 6.2: Back Button Mapping Process

6.3 Vibration Intensity Adjustment

The grip motors have 3 vibration intensity levels: Off, Low, and High. The factory default is Low.

  1. For the left or right controller, hold the TURBO button and push the joystick left (decrease) or right (increase) to adjust the grip vibration intensity.
  2. The levels cycle through Off → Low → High.
  3. After each adjustment, the controller will vibrate at the corresponding intensity for 1 second. When set to Off, there will be no vibration. The current vibration intensity is remembered even after power off.
Diagram illustrating how to adjust vibration intensity using the Turbo button and joystick, showing Off, Low, and High settings.
Figure 6.3: Vibration Intensity Adjustment

6.4 RGB Lighting

The controllers feature customizable RGB lighting.

  1. Cycle Lighting Modes: Hold the TURBO button and single-press the left controller's - button or the right controller's + button to cycle through modes. Modes include eight solid colors (Red, Orange, Yellow, Green, Blue, Indigo, Purple, Pink) and one mixed-color mode (top-left Yellow, bottom-left Blue, top-right Red, bottom-right Green).
  2. Turn Off/Change Mixed-Color Modes: Hold the TURBO button and double-press the left controller's L3 or the right controller's R3 button.
    • First double-press: Turns off all RGB lighting.
    • Second double-press: Activates mixed-color breathing mode.
    • Third double-press: Activates mixed-color flowing light mode (left joystick ring flows clockwise, right joystick ring flows counter-clockwise).
  3. Adjust Brightness: Hold the TURBO button and press and hold the left controller's L3 or the right controller's R3 button. The brightness will cycle from dim to bright. Release the button to set the brightness. The controller will remember the last lighting effect state (except in lock mode).
Diagram showing how to cycle RGB lighting modes and adjust brightness using the Turbo button and other controls.
Figure 6.4: RGB Lighting Control

6.5 Power On/Off

  • Power On (Reconnect): In the off state, press any button to power on and enter reconnect mode.
  • Power On (Pairing): In the off state, hold SYNC for 3 seconds to power on and enter pairing mode.
  • Power Off: In the on state, hold the left controller's Capture button / right controller's Home button for 3 seconds.
  • Immediate Power Off: In the on state, short press the SYNC button.
  • Auto Power Off: The controller will power off if the connected host enters sleep mode or turns off Bluetooth.

7. Maintenance

7.1 Low Battery Warning

When the controller's battery voltage drops below 3.5V during connected use, the RGB indicator flashes red rapidly to warn that the controller needs charging. If the voltage falls below 3.4V, the controller automatically shuts down.

7.2 Auto Sleep

When connected to a host, the controller enters sleep mode after 10 minutes of inactivity. The sleep timer can be adjusted in the Keylinker App.

7.3 Charging

There are multiple ways to charge your NYXI Hyperion 3 JoyPads:

  1. Via Console Charging: Magnetically attach the controllers to the sides of the Switch 2 console. While the console is charging via its adapter, the controllers also charge. The RGB indicator breathes in its current color and stays solid when fully charged.
  2. Via Controller's USB Port Charging: Connect the USB-C cable directly to the controller. The RGB indicator breathes red while charging and turns off when fully charged. (Note: Cannot charge via the controller's USB port while connected to a host.)
  3. Via Center Bridge Charging: Connect a charger to the center bridge's charging port. Both left and right charging indicators on the bridge will flash red for 0.5s, then green for 0.5s, then turn off, indicating successful self-test and standby mode. Place a controller into a charging slot; its corresponding indicator lights solid red. It turns solid green when fully charged. Removing the controller turns off its indicator.
Diagram illustrating the different charging methods for the NYXI Hyperion 3 controllers, including direct USB-C connection and charging via the center bridge.
Figure 7.1: Charging Methods

8. Troubleshooting & Reset

8.1 Reset

If the controller malfunctions (e.g., button confusion, freeze, connection failure), try resetting it.

Method: Press and hold the HOME or Capture button for 10 seconds, or short press the SYNC button to reset the controller state.

Diagram showing the locations of the HOME, Capture, and SYNC buttons for resetting the controller.
Figure 8.1: Controller Reset Options

8.2 Lock Mode

Lock mode prevents accidental inputs and saves battery.

  • Activate: With the controller off, press and hold the SL + SYNC (MODE) buttons for 5 seconds. After the RGB indicator flashes red slowly 3 times, the controller enters lock mode. Pressing any button will not wake it.
  • Deactivate: Connect the controller to a host magnetically or plug in a USB cable for charging. This exits lock mode, allowing wake-up via any button.
Diagram illustrating how to activate lock mode by pressing and holding the SL and SYNC buttons.
Figure 8.2: Lock Mode Activation

8.3 Gyroscope Calibration

To ensure accurate motion control, calibrate the gyroscope:

  • Left Controller: In sleep mode, press the combo [L + UP + CAP (Capture button)] simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press [-], wait a moment to exit calibration mode.
  • Right Controller: In sleep mode, press the combo [R + X + HOME] simultaneously. Enter calibration mode (RGB indicator flashes cyan slowly). Place the controller flat on a level surface/in a jig. Press [+], wait a moment to exit calibration mode.
  • Alternative Method via Host: On the console, go to Settings > Controllers & Sensors > Calibrate Motion Controls, then press and hold "+" or "-".
Diagram showing the buttons used for gyroscope calibration on both left and right controllers.
Figure 8.3: Gyroscope Calibration Buttons

8.4 Joystick Calibration

After connecting to the host, go to Settings > Controllers & Sensors > Calibrate Control Sticks to calibrate the joysticks.

8.5 Firmware Upgrade

Keep your controllers updated for optimal performance:

  1. OTA via Phone: Connect to the KeyLinker App and use the OTA upgrade option in the menu.
  2. Via PC Software: Start the latest firmware upgrade software on a PC. With the controller off, hold the L3 (left joystick) or R3 (right joystick) button, then connect via USB cable. Once the "Upgrade" button becomes clickable, click it to start the upgrade.
  3. Firmware upgrades do not delete the controller's saved settings.

9. User Tips

  • Ergonomics: Many users find these controllers significantly more comfortable than original Joy-Cons, especially for larger hands, allowing for longer gaming sessions without cramps.
  • Precision: The Hall effect joysticks and mechanical micro-switch buttons offer enhanced precision and tactile feedback.
  • Firmware: Some units may come with the latest firmware pre-installed, ensuring compatibility with the Switch 2 handheld boost mode update right out of the box.
  • Initial Setup: If you experience ghost inputs, performing a factory reset on both Joy-Cons can resolve the issue.
  • Center Bridge: When using the center bridge to combine the controllers into a single gamepad, be aware that some users report it can feel slightly wobbly.
  • Back Button Mapping: Note that back button mapping works for each controller separately; they cannot map each other's buttons.

10. Regulatory Information

10.1 FCC Compliance Statement

Model: NS-202

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

10.2 CE Declaration of Conformity

Model: NS-202

Product Code: NJ22

The product conforms to EC standards for radio interference. Shenzhen MIKE Morgen Technology Co., Ltd. declares that the NS-202 radio equipment conforms to the Directive. Applicable standards include EN IEC 62368-1:2020+A11:2020, EN 50663:2017, EN 62479:2010, ETSI EN 301 489-1 V2.23(2019-11), ETSI EN 301 489-17 V3.2.4(2020-09), ETSI EN 300 328 V2.2.2(2019-07).

The full text of the EU Declaration of Compliance can be found on: www.nyxigame.com

10.3 Disposal Information

The symbol WEEE symbol indicates that the product should not be disposed of with household waste but should be brought to an appropriate collection point for recycling. According to local regulations, do not dispose of the product or rechargeable battery with normal household waste. Appropriate disposal of used products and rechargeable batteries helps to prevent negative impacts on the environment and human health.

11. Warranty & Support

For warranty information, please refer to the product user manual (warranty card) included in your package. For further support or to view the full EU Declaration of Compliance, please visit the official NYXI website: www.nyxigame.com.

12. Precautions

  • Do not expose the product to liquid.
  • Do not disassemble the product.
  • Avoid dropping the product.
  • Avoid exposing the product to extremely high or low temperatures.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.