1. Introduction
Thank you for choosing the SZSINOCAM Wireless Solar-Powered Camera. This manual provides detailed instructions for setting up, operating, and troubleshooting your new security camera. Please read this guide thoroughly before use to ensure proper functionality and safety.
Important Note: This camera supports 2.4GHz WiFi connectivity only. It does not support 5GHz WiFi networks.

Figure 1: Camera Overview with Key Features
2. Product Components
2.1. Camera Diagram

Figure 2: Camera Features Diagram
Front View
- WIFI Antennas: For wireless connectivity.
- Night Lights: Provide illumination for night vision.
- Lens: Captures video footage.
- MIC: Microphone for audio input.
- Photosensitive Sensor: Detects ambient light for automatic mode switching.
- PIR Sensor: Passive Infrared sensor for motion detection.
Bottom View
- Reset Button: Used to reset the camera to factory settings.
- TF Card Slot: For inserting a Micro SD card (up to 256GB).
- Speaker: For two-way audio output and alerts.
- Charge Port: USB port for charging the built-in battery.
- OFF-ON Switch: Power switch for the camera.
2.2. Package Contents
- SZSINOCAM Wireless Solar-Powered Camera
- Solar Panel
- USB Cable
- Tweezers
- Screws and Anchors (x7)
- Threaded Bracket Drilling Template
- Fixed Plate Positioning Sticker (Orientation)
- Support Plate
- Quick Start Guide (this manual)
3. Setup Guide
3.1. Battery Charging
The camera has a built-in large-capacity battery. For safety regulations during shipping, the battery is not fully charged. Please charge the camera using the provided USB cable and a 5V adapter (not included).
- When charging, the LED indicator light will be red.
- When fully charged, the red light will turn off.
- A full charge takes approximately 4 hours.
LED Indicator Information
| LED Indicator | Description |
|---|---|
| Blue light flashes slowly | Waiting for network configuration |
| Blue light is always on | Configuration complete |
| Blue light flashes quickly | Disconnected from the network |
| Green light flashes slowly | Restoring factory settings / Device unbinding |
| Green light is always on | AP mode |
| Steady red light | Charging |
| Red light goes out | Fully charged |
3.2. Micro SD Card Installation
The camera features a built-in micro SD card slot, supporting cards up to 256GB. Ensure the camera is turned OFF before inserting the Micro SD card.
- Open the silicone cover at the bottom of the bracket.
- Ensure the toggle switch is in the "OFF" state.
- Open the black rubber plug on the camera.
- Using tweezers, hold the SD card and insert it into the SD card slot until it clicks into place.
- Push the silicone cover back to seal the slot.
3.3. Antenna Placement
For optimal signal reception, ensure the antennas are placed correctly.

Figure 3: Correct Antenna Placement (V-shape)
3.4. App Download and Installation (O-KAM Pro)
To control and monitor your camera, download the O-KAM Pro app.
- Scan the QR code below with your phone's camera.
- Alternatively, search for "O-KAM Pro" in the Apple App Store or Google Play Store.

Figure 4: O-KAM Pro App Download QR Code
3.5. Connecting the Camera to the App
Method 1: Scan Code Binding
- Ensure the camera is powered on and the blue LED indicator is flashing slowly (waiting for network configuration).
- Open the O-KAM Pro app and select "Add Device".
- Use your phone's camera to scan the QR code located on the camera body.
- Choose your 2.4GHz WiFi network and enter the correct password.
- The app will automatically proceed to the next interface upon successful QR code scan and connection.
Method 2: Fast Network Configuration (BT-enabled camera)
- In the app's "Add Device" interface, if a new device is discovered via Bluetooth, click "Connect".
- Select your 2.4GHz WiFi network and enter the correct password.
- Wait for the camera to connect to your router/server. The app will indicate when binding is complete.
3.6. Installation Location and Method
Finding a Good Installation Spot
- Perform a live view test in the app at your desired installation spot to ensure strong 2.4GHz Wi-Fi signal coverage. If the signal is weak, consider moving the router closer or using a Wi-Fi extender.
- Recommended installation height: 2-2.5 meters (6.5-8.2 feet).
- Ensure the camera's line of sight is not blocked.
- The PIR motion sensor has an effective range of approximately 10 meters (30 feet).
Camera Installation Steps
- Using the provided drilling template, mark 4 holes on the wall.
- Drill the holes using a 15/64" (6mm) drill bit.
- Insert the anchors into the drilled holes.
- Align the support plate with the holes and fix it to the wall using the screws.
- Align the slot at the bottom of the camera with the support plate. Ensure both sides of the camera are aligned with the screw holes on the support plate.
- Secure the camera using the 4 M4X8MM screws.
Solar Panel Installation Steps
This section applies only if your product includes a solar panel.
- Choose an area that receives full, direct sunlight year-round for several hours a day.
- Mount the solar panel bracket to your chosen location using the included screws and anchors. If the surface is soft or unstable, drill pilot holes first.
- Screw the gimbal into the back of the solar panel and tighten the included nut.
- Screw the locking screw into the assembly. Ensure the universal joint is angled upward.
- Adjust the solar panel to the desired angle (up to 90° vertical adjustment is possible) to maximize sun exposure, then tighten the locking screw to secure it in position. A tilt of 30-35° is often optimal.
- After installation, check that all locking mechanisms are tightly secured.

Figure 5: Solar Panel and Camera Installation Example
4. Operating Instructions
4.1. Live View and PTZ Control
Once the camera is connected to the O-KAM Pro app, you can access the live view and control its functions.
Video 1: Demonstration of app control and camera features, including PTZ movement and night vision.
- Pan/Tilt/Zoom (PTZ): The camera supports 355° horizontal (pan) rotation and 90° vertical (tilt) rotation. Use the controls in the app to adjust the viewing angle. The camera features 4X digital zoom.
- Pre-position Cruise: Set specific points for the camera to automatically patrol.
- Vertical/Horizontal Cruise: Enable automatic scanning across vertical or horizontal axes.
- White Light/Spotlight: Manually activate the white light for illumination or as a deterrent.
- Screenshot/Record: Capture still images or record video directly from the live view.
4.2. Two-Way Audio
The camera features a built-in microphone and speaker, enabling two-way voice intercom. You can speak through the app and hear audio from the camera's location.

Figure 6: Two-Way Audio in Use
4.3. Night Vision Modes
The camera offers three night vision modes for clear monitoring in low-light conditions:
- Intelligent Detection Mode: Automatically switches between infrared and full-color night vision based on detected motion.
- Infrared Mode: Provides black and white video using infrared LEDs.
- Night Vision Full Color Mode: Uses built-in white lights to provide full-color video at night.

Figure 7: Three Night Vision Modes
4.4. Motion Detection and Tracking
The camera features advanced AI functions for human detection and motion tracking.
- Human Detection: The camera can recognize human figures in the monitoring area and send real-time alerts to your phone.
- Motion Tracking: When motion is detected, the camera can automatically follow the moving object within its pan/tilt range.
- Audible and Visual Alarm: The camera can trigger an alarm (siren and flashing lights) upon detection.

Figure 8: Motion Detection and Tracking
4.5. Video Recording and Storage
The camera supports multiple video recording and storage options:
- Cloud Storage: Video records can be uploaded to cloud storage (paid activation may be required).
- TF Memory Card: Supports local storage on a Micro SD card (up to 256GB). When the memory is full, older recordings will be automatically overwritten.

Figure 9: Cloud and TF Card Storage Options
4.6. Device Sharing
You can share access to your camera with family and friends through the O-KAM Pro app.
- Open the O-KAM Pro app and select your camera from the homepage.
- Go to "Camera Settings" and click on "Share".
- A QR code will be automatically generated. Your friends can scan this QR code with their O-KAM Pro app to gain access.
Note: If you turn off sharing permissions, shared users will only be able to view the video but cannot control camera functions.
5. Maintenance
- Solar Panel Cleaning: Regularly wipe the face of the solar panel with a soft, damp cloth to clear any dust or debris, ensuring optimal charging efficiency.
- Firmware Updates: Ensure you update the camera's firmware to the latest version for improved performance and security. Check the app for available updates.
6. Troubleshooting
6.1. Cannot Add Camera for the First Time
- Ensure the camera is powered on and the working status light is blinking blue slowly, or you hear the prompt "Please use the App to configure WiFi".
- Verify your WiFi account name and password are correct.
- Ensure your network is stable and smooth. Operate the camera close to the router during setup.
- If QR code network configuration fails, try using the AP network configuration method (connect to the camera's WiFi hotspot and return to the app).
- Avoid using overly complicated WiFi passwords or those containing special characters like '\'.
- If both methods fail, restart your router and try again.
- If issues persist, provide the nameplate label of your router to customer support for assistance.
6.2. SD Card Not Recognized
- Check if the SD card capacity is displayed in the app under "System Settings" > "SD Card Recording Settings". If it shows "No SD card detected", the card recognition failed.
- Use a reputable brand Micro SD card.
- Ensure the SD card can be recognized by a computer.
- Only FAT32 format is supported.
- Recommended capacity is 2GB-256GB, Class 4 or above.
- Try inserting and unplugging the SD card several times.
- Try using a different Micro SD card.
- After inserting the card, wait for approximately 30 seconds for the camera to recognize it.
6.3. Equipment Fails to Respond
- Long press the power button to restart the camera.
- If there is no response, open the USB silicone cover at the bottom of the camera, long press the reset button, and then long press the power button to restart the camera.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | SZSINOCAM |
| High Definition | 3.0 Megapixels (2K Ultra HD) |
| Connectivity | WIFI (2.4GHz only) |
| Lens (mm) | 4mm |
| Sensor | CMOS |
| Style | Dome Camera |
| Power Source | Solar Powered (Built-in Rechargeable Battery) |
| Solar Panel Power | 5W |
| Operating Voltage | 5V DC |
| Operating Temperature | -20.5°C to 48.5°C (-5°F to 120°F) |
| IP Rating | IP66 (Waterproof / Weatherproof) |
| Movement Range (Pan) | 355° |
| Movement Range (Tilt) | 90° |
| Digital Zoom | 4X |
| IR Distance | 30M |
| Color Night Vision | Yes |
| Audio Output | Two Way Audio |
| AI Functions | Human Detection |
| Video Compression Format | H.264 |
| TF Card Support | Up to 256GB (FAT32 format, Class 4+) |
| Supported Mobile Systems | Symbian, Windows Mobile, Android, iOS |
| Installation | Wall Mounted, Pendant Mount, Corner Mount |
| Shell Material | Plastic |
| Certifications | CE, EAC, EPA, FCC, RoHS, UL, KC, pse, weee |
8. Compliance and Support
8.1. Disclaimer
⚠️ Camera products can only be used for purposes permissible under applicable law and regulations. Misuse of the product for any illegal activities is strictly forbidden. Please comply with the applicable laws and regulations in your country/area.
8.2. FCC Warning
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
8.3. ISED Canada Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
8.4. Additional Resources
A detailed user manual in PDF format is available for download. Please refer to the official product page or contact customer support for the link: User Manual (PDF)