Rakoncnc 1000W/1500W/2000W/3000W/4KW/5KW/6KW

Contents

Rakoncnc High Accuracy Laser Welding Machine 4-in-1

Model: 1000W/1500W/2000W/3000W/4KW/5KW/6KW

Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and efficient operation and maintenance of your Rakoncnc 4-in-1 Laser Welding Machine. This machine is designed for welding, cutting, and cleaning various metal materials. Please read this manual thoroughly before operating the equipment.

For detailed instructions and operation videos, please refer to the full user manual (PDF) or contact us at: Info@rakoncnc.com.

The full user manual (PDF) can be found at: User Manual (PDF)

2. Safety Precautions (Required Reading)

Hazard: Laser Radiation

  • Never look directly at the laser beam or reflected light.
  • Dedicated laser safety glasses must be worn.
  • Protective screens must be set up in the welding area; unauthorized personnel are prohibited from entering.
  • Remove reflective items such as metal watch straps and jewelry while working.

Warning: Fire Risk

  • Flammable and explosive materials must not be placed within 2 meters of the work area.
  • Fire extinguishers must be readily available.
  • Unattended operation of equipment is strictly prohibited.

Note: Other Hazards

  • Equipment must be properly grounded.
  • Maintain ventilation during welding.
  • Do not squeeze or step on the welding torch cable.

3. Equipment Components

The Rakoncnc Laser Welding Machine typically includes the following main components:

  • Main Unit: Houses the laser source, control system, and water chiller.
  • Handheld Welding Torch: Includes the fiber optic cable for laser delivery.
  • Wire Feeding Mechanism: Automatic wire feeder for continuous welding.
  • Accessories: Safety goggles, various nozzles, and protective lenses.
Rakoncnc Laser Welding Machine main unit and components
Figure 1: Main unit and various components of the Rakoncnc Laser Welding Machine.
Control panel and welding torch of the laser machine
Figure 2: Close-up view of the control panel and handheld welding torch.

4. Setup Instructions

4.1 Pre-start Checks

  • Ensure the coolant level in the water chiller is normal.
  • Verify that the protective lens is clean and free from debris.
  • Check that the wire feed nozzle is unobstructed.
  • Confirm that the grounding wire is securely connected to prevent electrical hazards.

4.2 Startup Sequence

  1. Connect the main power supply to the machine.
  2. Start the water chiller.
  3. Wait for the water temperature to stabilize (approximately 30 seconds).
  4. Turn on the laser key.
  5. Start the control software.
  6. The standby green light should illuminate, indicating the machine is ready.

5. Operating Instructions

This machine supports welding, cutting, and cleaning functions. The following instructions detail the welding operation. For cutting and cleaning operations, please refer to the comprehensive PDF manual.

5.1 Test Weld

  • Position the nozzle 10-15mm from the workpiece.
  • Press the switch on the welding torch and observe the position of the red light indicator point on the workpiece. This indicates the laser's target.
  • Test the laser beam without wire feeding to ensure proper alignment and power settings.

5.2 Arc Initiation Welding

  1. Tilt the welding torch at approximately a 75° angle relative to the workpiece.
  2. Press the laser switch first.
  3. Shortly after, press the wire feed button to begin feeding welding wire.
  4. Maintain a constant speed during welding, pausing for no more than 0.3 seconds to ensure a consistent weld bead.
Video 1: Demonstration of the laser welding process on metal surfaces.

6. Maintenance

6.1 Daily Shutdown Procedure

  1. Stop laser emission.
  2. Turn off the laser key.
  3. Continue water flow for 5 minutes to allow the system to cool down.
  4. Turn off the water chiller.
  5. Turn off the main power supply.
  6. Clean the nozzle and protective lens.

6.2 Routine Maintenance

  • Every 4 hours: Check the protective lens. Replace immediately if contaminated or damaged.
  • Daily: Empty the water tank filter.
  • Weekly: Check the wire feed tube for wear and tear.
  • Monthly: Clean radiator dust to ensure efficient cooling.

7. Troubleshooting

This section provides general guidance for common issues. For complex problems, consult the full user manual or contact technical support.

  • No Laser Emission: Check power connections, laser key status, and control software settings. Ensure all safety interlocks are engaged.
  • Poor Weld Quality: Verify nozzle distance, laser power settings, wire feed speed, and torch angle. Ensure the workpiece is clean.
  • Overheating: Check water chiller function, coolant level, and ensure radiator is free of dust. Verify proper ventilation.
  • Wire Feed Issues: Inspect the wire feed tube for blockages or wear. Ensure the wire spool is correctly installed and not tangled.

8. Specifications

Feature Specification
Brand Name rakoncnc
Model Number 1000W/1500W/2000W/3000W
Max. Output Power 1000W/1500W/2000W/3000W
Rated Voltage 220V
Origin Mainland China
Use Welding, cutting, cleaning
Certification CE
Wavelength 1070nm
Pulse Width 0.1-80MS
Focal Spot Diameter 0.5mm
Welding Gap Requirements ≤1.2mm
Laser Source MAX/Raycus/BWT
Laser Head Single/ Dual Axis

9. User Tips

  • Always perform a test weld on scrap material before working on your final piece to fine-tune settings.
  • Ensure the workpiece is clean and free of rust, paint, or oil for optimal welding, cutting, and cleaning results.
  • Regularly check and clean the protective lens and nozzle to maintain laser beam quality and prevent damage.
  • When switching between welding, cutting, and cleaning modes, ensure appropriate safety measures and settings are applied.

10. Frequently Asked Questions (FAQ)

For a comprehensive FAQ section, please refer to the full user manual (PDF) or contact our support team.

  • Q: What types of metals can this machine process?
    A: This machine is suitable for welding, cutting, and cleaning various metals. Specific material compatibility details are available in the full manual.
  • Q: How often should the coolant be checked?
    A: The coolant level should be checked during pre-start checks, and the water tank filter should be emptied daily as part of routine maintenance.
  • Q: Can I use this machine for purposes other than welding, cutting, and cleaning?
    A: The machine is designed for these three primary functions. Using it for other purposes may void the warranty and pose safety risks.

11. Warranty and Support

For detailed warranty information, technical support, and service inquiries, please contact Rakoncnc directly.

Email: Info@rakoncnc.com

Website: https://www.rakoncnc.com

This instruction manual is a simplified, general version; for detailed instructions and operation videos, please contact us at the provided email address.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.